Vision 1480 Series User manual
© 2011-2014 KIRAMEK, INC., Aichi Japan
Ver. 1.7, Feb. 2014
DIGI
LINK
SMART
FACTORY KEYLESS UPGRADE SECURITY
1480
series
Thank you for purchasing this VISION
1480 Vehicle Security System. The 1480
is a state of the art device that will pro-
vide you with years of trouble free ser-
vice if used properly. Please familiarize
yourself with the content of this Owner’s
Guide to get the most out of your new
system. We trust you will enjoy using the
product.
© 2011-2014 KIRAMEK, INC.
NOTICE! Although reasonable efforts have been taken to ensure accuracy in this
Owner’s Guide, Kiramek Inc. shall not be held liable for any errors, omissions, prop-
erty damage, or injury resulting from the use of this information.
All product specifications and features are subject to change without notice.
TA B L E O F C ON T E N T S
Limited Lifetime Warranty ................................... 1
Included Items ............................................ 2
Arming & Disarming ....................................... 3
Arming ................................................ 3
Confirmation Chirps .................................... 3
Disarming ............................................. 4
Manual Disarming ...................................... 5
Main Features ............................................ 6
Trunk Release Bypass .................................... 6
Door Trigger ........................................... 6
2-Stage Shock Sensor ................................... 6
Ignition Trigger ......................................... 7
Hood Trigger ........................................... 8
Error Chirp ............................................. 8
GWA (Ground When Armed) ............................. 8
SBS (Sector Bypass System) ............................... 8
Status LED ............................................. 9
Hazard Flash .......................................... 10
Resume .............................................. 10
Valet Mode........................................... 10
Programmable Features ................................... 11
Troubleshooting .......................................... 14
Options ................................................. 16
1
© 2011-2014 KIRAMEK, INC.
The VISION 1480 system control unit is backed by a limited lifetime
warranty against defective components and/or improper product assem-
bly to the original purchaser for as long the vehicle is owned by that
same purchaser, contingent upon installation by an Authorized VISION
Dealer. All product warranties become void if the VISION 1480 system
was not sold and installed by an Authorized VISION Dealer or the sys-
tem is moved to another vehicle. All other parts and/or accessories that
connect to VISION 1480 systems, including but not limited to the Siren,
Shock Sensor and LED Program Switch, are warranted for one (1) year
from the original date of purchase.
During the warranty period, Kiramek Inc. will repair or replace, at its
sole discretion, any system component that is found defective in mate-
rial or assembly during the warranty period, provided that the product
is returned to Kiramek Inc. by an Authorized VISION Dealer and is ac-
companied by a clear and legible copy of the original purchaser’s receipt.
Any damage to your VISION 1480 system that results from normal
wear-and-tear, accidents, improper use, neglect, faulty wiring, incorrect
number, alteration or repair outside Kiramek Inc or its Authorized VI-
SION Dealers immediately voids this warranty.
This warranty is limited to defective parts only and does not provide
any compensation whatsoever for damages associated with the VISION
1480 system or its accessories. This warranty does not cover installa-
tion labor, product removal and/or reinstallation fees. This warranty
is valid for the original purchaser only and may not be transferred to
another party. Kiramek Inc makes no warranty against theft or vandal-
ism of the vehicle in which the VISION 1480 system was installed. This
warranty shall not be interpreted as an insurance policy against loss,
otherwise.
WARNING! DO NOT ATTEMPT TO INSTALL THIS VISION 1480 PRODUCT YOUR-
SELF BECAUSE SUCH WILL IMMEDIATELY VOID THE WARRANTY. THIS SECU-
RITY SYSTEM MUST BE PROFESSIONALLY INSTALLED BY YOUR AUTHORIZED
VISION DEALER TO VALIDATE YOUR WARRANTY.
Limited Lifetime Warranty
2
VISION 1480 OWNER’S GUIDE
INCLUDED ITEMS
LED Program Switch Parts
Status LED
Program Switch
FACTORY KEYLESS UPGRADE SECURITY
1480
DIGILINK
SMART
Control Module (1pc)
Shock Sensor (1pc)
LED Program Sw. (1pc)
Siren (1pc)
Control Mod. Harnesses (2pcs)
Sensor Harness (1pc)
Sensor Tape (1pc) Window Decals (2pc) Guides (2pc)
VISION
IR SHOCK SENSOR
Only 1480B includes keys.
FACTORY KEYLESS UPGRADE SECURITY
1480
series
DIGILINK
SMART
25cm Wire Ties (2pcs)
PosiTap Connectors (4pcs)
PosiLock Connector (1pc)
RED
(p/n NT-4)
Dark RED
(p/n NL-1)
VISION 1480 OWNER’S GUIDE
3
Arming & disarming
ARMING
CONFIRMATION CHIRPS
NORMAL ARMING
Close all doors and then LOCK by your factory
keyless remote or by SmartKey door handle
touch.
ON). The Status LED will light for 5s, during which
time all triggers are disabled. Then the Status LED
triggers become enabled. The Shock Sensor (and any other external sen-
SENSOR BYPASS ARMING
This procedure lets you temporarily disable
the Shock Sensor for a single Arming session:
1) With Ignition OFF, press the Program Switch twice.
2) Within 20s, press LOCK on the factory remote to Arm.
The system is now Armed in Sensor Bypass Mode, and all triggers are active
except the shock sensor and any other external sensors. Note that when you
Disarm and then Arm again normally, the shock sensor will be enabled.
(ON by default)
This procedure lets you enable or disable the
Arm/Disarm chirps. (Note that the siren will
still go off when the 1480 is triggered.)
1) With Ignition OFF, press the Program Switch once.
2) Within 20s, press LOCK on the factory remote to Arm.
-
1 Push
2 Pushes
LOCK
OFF
OFF
PROGRAMMABLE
© 2011-2014 KIRAMEK, INC.
4
arming & disarming
DISARMING
NORMAL DISARMING
UNLOCK by your factory keyless remote or by
SmartKey door handle touch. Vehicle hazard
will chirp 3 times
and the Status LED will turn off. The 1480 is now
Disarmed and you may enter the vehicle.
If the siren chirps 4 times when you Disarm, it means something had trig-
gered while you were away from the vehicle. In this case, the Status LED
Some vehicles equipped with remote engine starters do not allow you to
Unlock while the engine is running. In such a case, you will not be able
to Disarm the 1480 until you shut off the engine.
NOTE
UNLOCK
DISARMING DURING THE SIREN BLAST
If the siren is triggered by the opening of a door or the back hatch,
you should close any open doors or the back hatch before you press
Unlock on your factory remote to disarm. The reason is because some cars
require doors to be closed before you can Unlock with the factory keyless
remote.
Also, if the siren is blasting and the doors are already unlocked, you may
not be able to Disarm the 1480 with a simple press of Unlock. In such a
case, you will need to and then press Unlock to Disarm.
This is also true in cases where the car’s factory remote only has a single
Lock/Unlock button—you’ll have to push the button twice.
5
© 2011-2014 KIRAMEK, INC.
ARMING & DISARMING
MANUAL DISARMING
You can manually Disarm using a secure code in the event your
factory remote’s battery dies (see Note 2 below). The factory set
code is “6”, but you can change this code to another number of
your choosing for greater security (see the bottom of this page).
1) Enter the car. (The siren will go off. You can leave the door open or closed.)
2) Turn ON the Ignition.
3) Within 30s, press the Program Switch the same number of times as
your Disarm Code. (Factory Default Code = 6)
4) Turn OFF the Ignition. (The 1480 will now Disarm and the siren will
stop. NOTE
1) If the 1480 won’t Disarm, you entered the code incorrectly. Close the
door, wait for the siren to stop, then start over from Step-1.
2) Many Push Start cars don’t allow the Ignition to be turned on with-
out the presence of the Factory Remote. So if you lose or destroy your
car’s remote, you may not be able to Manually Disarm the 1480. But if
your remote’s battery merely dies, you will be able to switch on the Igni-
tion and Manually Disarm using the 4 steps above.
NOTES
DISARM CODE CUSTOMIZATION
The factory code is “6” but you should change it to another number between 1 & 30:
1) With the 1480 Disarmed, turn ON the Ignition.
2) Press the Program Switch for 6s, after which the siren will chirp 3 times.
3) Release the Program Switch and turn OFF the Ignition. The Status LED
will light for 5s.
4) Turn ON the Ignition again (while the LED remains lit for 5s).
5) When the LED turns off, wait about 4s and you will see the LED start to
-
Turn OFF the Ignition to program your code.
If you have the optional paging system, you must now relearn your pagers.
PROGRAMMABLE
6
VISION 1480 OWNER’S GUIDE
MAIN FEATURES
Some cars don’t support the automatic trigger bypass feature of the
use your factory Trunk Release feature (otherwise the siren will trigger).
NOTE
For cars that support it, pressing the Trunk
Release button on the factory remote will
bypass the shock sensor and trunk triggers
while the trunk opens. Door and Ignition switch
triggers remain active, and doors remain locked.
Five (5) seconds after you close the trunk, the
shock sensor and trunk triggers will be automatically re-activated.
TRUNK RELEASE BYPASS
TRUNK
The siren will blast for 30s when any door is opened
while the system is Armed. Vehicle hazard lights may
See bottom half of page 4 on how to Disarm
DOOR TRIGGER
2-STAGE SHOCK SENSOR
1st Stage (“Warning Chirps”). Each time the Shock
Sensor detects a light impact to the vehicle body, the si-
ren will chirp 5 times. Sensors will not trigger the siren
while in Sensor Bypass Mode.
2nd Stage (“Full Trigger”). When the Shock Sensor de-
tects a hard impact to the vehicle body, the siren will
blast for 30s (or until Disarmed with the factory remote).
Sensors will not trigger the siren while in Sensor Bypass
See page 15 for common shock sensor problems and solutions.
5 Chirps
30s Blast
The siren will blast for 30s when the trunk is opened
(without the remote) while the system is Armed. Ve-
See bottom half of
TRUNK TRIGGER
7
© 2011-2014 KIRAMEK, INC.
MAIN FEATURES
IGNITION TRIGGER
IG PROTECT MODE (default)
The siren will blast for 30 seconds when the
Ignition (IG) switches ON while the system is
(To Disarm and stop the siren,
turn off the Ignition and then press Unlock on the factory remote.)
REMOTE START COMPATIBILITY MODE (RSCM) (user-programmable)
When the Ignition switches ON while Armed in this
mode, the siren will not trigger. Instead, Shock
Sensor and Ignition triggers are bypassed, while
Door, Hood & Trunk triggers remain active. This
allows 3rd party remote starters to start the engine
without triggering the siren. The vehicle is still protected though, and any
attempt to open a door or the trunk will trigger the siren. And when the
remote starter stops the engine (i.e., Ignition turns off), Sensor and Ignition
triggers are automatically re-activated.
(See page 11 to program.)
IIP (Intelligent Ignition Protect)
IIP activates when you program RSCM. The function of IIP is to
temporarily switch back to IG Protect Mode after a siren trigger.
Purpose. Most “remote start / turbo timer” compatible car alarms by-
pass all trigger inputs after the Ignition is switched ON. So if a thief
opens a door the siren will trigger; but the thief can then close the door,
turn on the Ignition, wait until the siren stops, then drive away in si-
lence because the Ignition-ON state prevents the siren from triggering
again! And other car alarms that always trigger the siren when the Ig-
nition turns on offer no remote start or turbo timer compatibility at all.
IIP
How it works. Normally, if the Ignition is turned ON while in RSCM,
the system automatically bypasses the Sensor & Ignition triggers but
keeps Door, Hood and Trunk triggers active. But if the 1480 is triggered
by a Door or Sensor before the Ignition is turned ON, IIP automatically
switches back to IG Protect Mode, and the siren will be triggered if the
Ignition is turned on. Disarming and Arming again will revert to RSCM.
PROGRAMMABLE
IG ON
IG ON
L
O
C
K
A
C
C
O
N
S
T
A
R
T
START
STOP
8
VISION 1480 OWNER’S GUIDE
MAIN FEATURES
GWA (Ground When Armed)
The 1480 feeds a (–) Ground output while the system is Armed.
Optional devices can be activated by this control line, such as
a Starter Kill Immobilizer Relay or LED scanners. When the
system is Disarmed, GWA is switched OFF and all attached devices turn
off. See the
A “sector” is the Ignition, the Hood, any Door, and attached Sen-
sors. When a sector triggers the siren a certain number of times
(see below), that sector is bypassed (disabled) until you Disarm
and Arm again. This limits noise pollution caused by multiple
siren triggers in a short period of time (such as when you park
near construction sites or if animals jump on the vehicle repeatedly).
DOOR — If a Door is left OPEN, the siren blasts up to 5 times (30s each
time), then the Doors are bypassed until closed. (The
input wire, is bypassed after it triggers the siren 10 times).
IGNITION — If the Ignition is left ON, the siren blasts up to 10 times (30s
each time) and then the Ignition is bypassed until you Disarm & Arm again.
SENSOR — Warning triggers (5 chirps) and Full Triggers (30s siren)
are independently bypassed after 10 times. You must Disarm and then
Arm again to re-activate.
SBS (Sector Bypass System)
OFF
HOOD TRIGGER
On compatible vehicles (or on any vehicle when the op-
tional analog Hood input is connected), the siren will
blast for 30 seconds when the hood is opened while the
ERROR CHIRP
If a Door or the Trunk is open when you Lock/Arm, you will hear 1 chirp
2 chirps-
mation Chirps are OFF). The 2 chirps are Error Chirps that notify you the
doors or the trunk will be bypassed because they are opened (they won’t
trigger the siren). Then 5s after you close the door(s) or trunk, they can
then trigger the siren if later opened. You will only hear Error Chirps on
VISION 1480 OWNER’S GUIDE
9
MAIN FEATURES
slowly about once per second while the system is
Armed, acting as a visual theft deterrent. The LED turns off when the
system is Disarmed, unless there was a siren trigger.
TRIGGER MEMORY
rapidly while the full siren blast is going off and
-
Table-1 below, showing you what triggered the siren.
If the siren triggered more than once, the LED will show you what caused
the last 3 triggers. Trigger Memory will displayed repeatedly on the LED
until the Ignition is switched ON or until you Arm again.
STATUS LED
TABLE-1 Status LED Trigger Memory
LED Flashes What Triggered the Siren
2Door
3Trunk (or back hatch)
4Hood (see Note below)
6Ignition
7Sensor (Full Trigger only)
There are no LED Flashes if the power is cut and then restored.
Door triggers. If you want Hood triggers to always report as Hood trig-
will need to purchase an optional Hood Pin Switch and have it installed
see the bottom entry on page 15 for more details about Hood trigger
reporting.
NOTE
© 2011-2014 KIRAMEK, INC.
10
MAIN FEATURES
HAZARD FLASH
times (depending on the car) when shock sensor Warning Chirps are trig-
will not receive any indication of being in Valet Mode. The security
system will be completely turned off. This also means that someone
could break into your car. Our company accepts no liability whatsoever
if your car is stolen or vandalized or its contents stolen due to your hav-
ing entered Valet Mode. You use this feature at your own security risk.
CAUTION!
Valet mode shuts down all functions of the security system, ensuring the
siren will never trigger. Valet Mode is useful when you must hand over
your car keys to a valet or car maintenance technician, so there is no worry
they will trigger the siren by accident.
Activation:
With the Ignition switched OFF and the 1480
Disarmed, press and hold the Program Switch for more
-
mediately light. But the LED will turn OFF after about 5s.)
When the LED turns OFF, release the Program Switch.
Deactivation:
Press and hold the Program Switch again for 5s, until the LED
turns OFF. Security features are now restored. (You may also hear 2 quick
Valet Mode PROGRAMMABLE
RESUME
RESUME is a form of State Memory that remembers if the system was
Armed or Disarmed when the main power is cut. When power is restored,
the 1480 will power-up Disarmed if it was disarmed in its previous state. If
originally Armed, it will power-up Armed and with the siren blaring.
Push 5s
11
© 2011-2014 KIRAMEK, INC.
11
PROGRAMMABLE FEATURES
You can change some features of the 1480 by using the Program
Switch. Perform the following 4-step procedure to change the fea-
tures shown in Table-2:
1. Start the engine and then Stop the engine. )
2. With the Ignition OFF, Arm the 1480 and then immediately Disarm.
3. Within 20s, turn ON the Ignition.
4. Press the Program Switch the same number of times as the feature you
want to program — refer to the “No.” column in Table-2 below. (For
h the Program Switch 8 times.)
5. Turn OFF the Ignition.
TABLE-2 Feature Selection Menu
No. Feature Description Toggle Settings
3 Ignition Trigger IG Protect RSCM
4 Hazard Flash During Remote Start OFF ON
7 Door Ajar Hazard Flash OFF ON
8 Auto Arm OFF ON
9 Siren Output Continuous Pulsed
10 Auto Rearm OFF ON
15 Speed Controlled Door Locking OFF ON
17 Exterior Illumination OFF ON
FACTORY DEFAULT SETTINGS SHOWN IN BOLD TEXT ABOVE
1)
-
programmed settings. To program another setting, repeat the 4 steps.
2)
NOTES
12
VISION 1480 OWNER’S GUIDE
When set to ON
turned on by a remote start system. (This feature only works if program
the Ignition Trigger to RSCM.)
4Hazard Flash During Remote Start
This feature automatically Arms the system when you do the following:
(1) turn Ignition ON & OFF then (2) Open & Close any Door. Upon seeing
these events, the system will Arm 20s after the last door is closed. The
doors will NOT be locked so you won’t be locked out if you leave your keys
in the car, but the system will be Armed and will trigger if a door is opened.
8Auto Arm
PROGRAMMABLE FEATURES
When set to IG Protect Mode (default), the system will trigger the siren
when the Ignition (IG) turns ON while Armed, as described on page 7.
When set to RSCM (Remote Start Compatibility Mode), the system will by-
pass the Shock Sensor and Ignition triggers when the Ignition turns ON
while Armed, as described on page 7.
3Ignition Trigger
When set to ON
is opened or left open while the Ignition is turned ON. Flashing will im-
mediately stop when the door is closed or the Ignition switched OFF.
NOTE
7Door Ajar Hazard Flash
9Siren Output
When set to
Continuous
(default), the system will feed a continuous
(+)12v output to sound the included siren for 30s (Full Trigger).
When set to
Pulsed
, the system will feed a pulsed (+)12v (3A max.) output.
This can be used to create a unique siren sound with the included siren (if
you cut the Blue loop wire on the siren), or used when connecting to the
vehicle’s horn by an optional relay.
You cannot Arm if IG is ON in IG Protect Mode
VISION 1480 OWNER’S GUIDE
13
13
PROGRAMMABLE FEATURES
This feature automatically Rearms the system 60s after it is Disarmed,
unless a Door is opened or the Ignition goes ON during the 60s. Doors will
be locked when the system Rearms.
10 Auto Rearm
When set to
ON
, vehicle Hazard lights will for 30s, or until a Door is
opened or until the Ignition is switched ON, in order to illuminate the area
around the vehicle for greater visibility and security.
17 Exterior Illumination
When set to ON, the Doors will Auto-Lock when the vehicle speed reaches
P (Park) position, the Doors will Auto-Unlock.
15 Speed Controlled Door Locking
1)
the doors manually, they will not -
cause they are already Unlocked in such a case, putting the gear into the
not
2)
there may be a second or two of noise appear on your in-dash TV. This
noise has nothing to do with the 1480 product or 1480 product installa-
tion. This is noise generated by your car’s door lock motors.
NOTES
© 2011-2014 KIRAMEK, INC.
14
FACTORY KEYLESS REMOTE WAS LOST, DISARMING
If the factory remote was lost, you may not be able to Disarm if you have
a Push Start car that requires the factory remote to turn on the Ignition.
In such a case, you must to contact your dealer for a replacement factory
remote. But if you have an older turn-to-crank style Ignition, you can
Disarm the 1480 by following Manual Disarming on page 5.
SOMETIMES CAN’T ARM/DISARM WITH THE FACTORY REMOTE
• On some cars, if you rapidly press Lock and Unlock on the factory re-
is simple —
•
chip when you tried to Arm? If not, the Ignition may be ON. You can-
not Arm the system while the Ignition is ON while in IG Protect Mode
(see the top of page 12).
THE SYSTEM IS DEFINITELY ARMED, BUT IT WON’T TRIGGER THE SIREN!
• It may be in Valet Mode. See page 10.
• It may be in Sensor Bypass Mode. See page 3.
SIREN BLASTS WHEN THE TRUNK IS OPENED
• You cannot open the trunk with the key or the siren will sound. Use
your factory remote. If your keyless remote doesn’t have a trunk open
your factory remote) and then open the trunk.
• If you open the trunk with your factory remote and the siren triggers,
it could be the trunk release timing is too long. After pressing Trunk
Release on your factory remote, the trunk must open within 2s or the
siren will sound.
• Some cars simply have a trunk release feature that is incompatible
then open the trunk.
CANNOT ARM WHILE 3rd PARTY TURBO TIMER IS IN USE
• Check if the doors Lock/Unlock by your factory remote while the turbo
timer is running. If not, the vehicle’s factory keyless system is incom-
patible with your turbo timer, which is why you cannot Arm the 1480.
• If the doors do Lock/Unlock with your factory remote while the turbo
timer is running, then make sure you have programmed RSCM (pg.11).
If you are using the default “IG Protect Mode,” you will not be able to
Arm while the Turbo Timer is running because the Ignition ON condi-
tion in that mode prevents Arming.
TROUBLESHOOTING
15
© 2011-2014 KIRAMEK, INC.
CANNOT DISARM WHILE THE SIREN IS SOUNDING
• Ensure all doors & trunk are closed, then try to Unlock to Disarm.
•
SHOCK SENSOR 1st STAGE “WARNING” TRIGGER DOESN’T WORK
Examine the shock sensor and look closely at the two LEDs.
• If you never see Green light, adjust the sensitivity knob on the sensor.
• If after increasing sensitivity you still don’t see the Green LED, it
could be that the suspended element inside the sensor body was shifted
out of place. See page 15 in the Install Guide on how to resolve this.
• If you do see a Green light, the sensor is functioning properly. That
means there is like a wiring problem. Check that the sensor wire har-
ness is properly connected at both ends.
FULL SIREN BLASTS WITH ONLY LIGHT IMPACT TO THE VEHICLE
• Turn down the shock sensor sensitivity.
• If you also have an optional Ultrasonic sensor installed along with the
shock sensor, it is very likely that the main body of the ultrasonic sen-
sor (not the 2 emitters) was placed too close to the shock sensor. The
main body of the Ultrasonic sensor should be placed more than 30cm (1
foot) away from the shock sensor to avoid interference.
HOOD TRIGGERS SIREN BUT TRIGGER MEMORY REPORTS DOOR & HOOD
Some Mercedes and BMW cars send a digital “door open” message on
the CAN when the Hood is opened. On these cars, if the 1480 is Armed,
the siren will trigger when the Hood is opened, even if the 1480’s Gray
wire is not connected to an optional Hood pin switch. But in this case,
Trigger Memory will report a Door Open trigger, not a Hood trigger.
However, if you purchase an optional pin switch and connect the 1480’s
Gray wire to it, Hood triggers will then report as both a Hood and a
Door trigger on the Status LED on some Mercedes and BMWs. You may
also see the Door and Hood icons on the LCD pager, if you purchase the
optional Paging System.
On cars where there is no digital CAN message sent when the Hood is
opened, a Hood open condition will not trigger the siren on those cars
unless you purchase an optional Hood pin switch and connect the 1480’s
gray wire to it. In this case, Trigger Memory and the LCD Pager will
report only a Hood trigger via the Gray wire.
TROUBLESHOOTING
16
VISION 1480 OWNER’S GUIDE
OPTIONS
The 1480 can be installed in your car without the need for any Options.
However, we do offer the following add-on products to enhance security
and convenience:
TR537S: 2-way LCD RF Paging Control System (ARIB-T67, for Japan)
or
TR835S: 2-way LCD RF Paging Control System (FCC, for USA)
896H-1B: Starter Kill Relay
896H-1CN: Relay to drive high-current devices like the Horn.
S-114R or S-113: Pin switch to detect Hood opening.
Optional Sensors:
• MMF-2: 2-stage Radar Sensor
• 318-022: 2-stage Digital Tilt Sensor
• 318-04: 1-stage Ultrasonic Sensor (not needed if you choose the MMF-2)
• 318-035: Sensor Splitter to easily connect up to 3 sensors at once
Luminator® LED Scanners
More details about add-on devices can be found on our website:
www.visionsecurity.jp/en/
9-183-1 Itayama-cho, Handa-shi, Aichi-Ken 475-0936 JAPAN
VISION products are engineered in Japan and manufactured in
strict accordance with Japanese QC standards at an ISO9000/
QS9000 certified factory.
Table of contents
Other Vision Car Alarm manuals
Popular Car Alarm manuals by other brands
CrimeStopper
CrimeStopper CS-9701 Gargoyle Owner's instructions
Ultra Start
Ultra Start MCS-100 owner's manual
Python
Python 881 XP installation guide
Scytek electronic
Scytek electronic 5100RS-22W product manual
Audiovox
Audiovox Pursuit PRO 9644a owner's manual
Audiovox
Audiovox Pursuit PRO-9675FT installation manual
