VISIONARY DESIGNS MOD-1245 Manual

© 2022
Order #59397
Top View
Front View
Perspective View
MOD-1245 Monitor Stand
If you would like to tell us about your experience with your setup instructions please email us at
[email protected]
SETUP INSTRUCTIONS

© 2022
Order #59397
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2022
Case 1 of 2
Order #59397 Case Packing
Setup Hardware
w/ Shelf Supports
Top View of Each Level
Level 1 (Bottom Level) Level 2
Counter Top
Shelf
3
1 2
4
Level 3
5,5A
6,6A 7,7A
8,8A,10
Literature Holders

© 2022
Case 2 of 2
Order #59397
Top View of Each Level
Level 1 (Bottom Level) Level 2 Level 3
9 9
Door
Infills
Monitor
Mount
Case Packing

© 2022
Step 1 of 2
Order #59397 MOD-1245 Assembly
Item
1
2
3
4
5,5A
6,6A
7,7A
8,8A
Description
38” RR91 Vertical Extrusion w/ Door Stop
38” RR91 Vertical Extrusion w/ Door Hinges
40” RR91 Vertical Extrusion
40” RR91 Vertical Extrusion
18.0868” Z45 Curved Horizontal Extrusion
13” Z45 Horizontal Extrusion
13” Z45 Horizontal Extrusion
14“ Z45 Horizontal Extrusion
Qty.
1
1
1
1
1,1
1,1
1,1
1,1
Steps:
1) Attach lower horizontals [5] [6] [7] and [8] between
verticals [1] [2] [3] and [4].
2) Slide infills between [1] [4], [2] [3], and [3] [4], making
sure Velcro is facing inward.
3) Connect door to vertical [2]. See Door Connection detail.
4) Attach upper horizontals [5A] [6A] [7A] and [8A] between
verticals [1] [2] [3] and [4] to secure infills.
1
6A
Infill
Infill
Infill
4
8A
3
7A
2
5
5A
Door
6
87
Door
Hinge
Hinge
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Connection
*
*
*
Partial Assembly

© 2022
Step 2 of 2
Order #59397 MOD-1245 Assembly Cont’d
*
Completed Assembly
**
9
10
9
4
3
2
Connector
Literature Holder Attachment
Locks
Literature
Holder
Attach angled end of connector to
literature holder. Attach flat end of
connector to vertical extrusion.
Tighten locks to secure.
*
*
*
Counter Top
Shelf
Item
9
10
Description
35” RR91 Vertical Extrusion
14” Z45 Horizontal Extrusion
Qty.
2
1
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Lock
12
*
Pin
Hole
Steps:
1) Connect shelf supports to Velcro on infills, then place shelf on top of supports.
2) Lock counter top to horizontals [6A] and [7A]. See Counter Top Lock detail.
3) Attach upper verticals [9] to lower verticals [3] and [4]. See Extrusion Connector detail.
4) Attach horizontal [10] between verticals [9].
5) Attach monitor mount to verticals [9]. See Monitor Mount Attachment detail.
6) Attach liturature holders to vertical [2]. See Literature Holder Attachment detail.
*
Set
Screw
Extrusion Connector
Set
Screw
*
Slide extrusion over connector
then secure with set screws.
To prevent product loss, keep
all screws attached to
connector after disassembling.
Connector
**
Monitor Mount
Attachment
Slide connectors into
grooves of verticals.
Tighten set screws.
Attach monitor mount
to connectors, using bolts.
Connectors
Monitor
Mount
*
Hex Bolt
& Washer