ICW Elite User manual
1
Elite Wall Mount Installation
1) Do not attempt to adjust your Elite arm un-
til everything you intend to mount to the arm is
mounted.
2) Arm must be completely horizontal (extended)
before adjusting the arms’ tension. Failure to do
so will damage the arm and void the warranty.
3) Never loosen or remove any
of the shoulder bolts. Doing so
will cause the arm to immedi-
ately come apart with tremen-
dous force, and could cause
serious injury.
4) If equipment requiring AC power is mounted
to this unit, have a certied electrician inspect the
installation.
5) Failure to install this unit according to these
instructions will void all ICW warranties. If in-
stalled incorrectly, ICW is not liable for any dam-
age or injury caused by the unit.
DANGER!
The Elite arm contains high
pressure gas springs. The fol-
lowing cautions MUST be ob-
served to avoid serious injury.
Shoulder bolt
Wall Mount
1 Locate a stud in the wall you intend to mount
your arm on and remove the wall mount from
the box. Mark the top hole, drill 11/64 pilot hole and
insert an ICW provided #14 screw and tighten slight-
ly. Using a level, mark the two lower holes and drill
pilot holes, insert the last two #14 screws and, with
the mount level, tighten all screws securely.
Note: ICW supplies #14 wood screws. If installing
onto metal studs you will need to replace with proper
metal stud fasteners. All hardware used to secure wall
mount must have a properly countersunk head.
2 Remove the four covers as shown.
Remove the center
cover by unscrewing
the 4 10-24 athead
screws using the 1/8
hex key.
Remove the long arm
covers by unscrewing
the 2 6-32 athead
screws using a philps
head screwdriver.
Remove the end
cover by unscrew-
ing the 2 10-24
screws using the
1/8 hexkey.
Note: The wall mount is shipped with
the bearings wrapped and it is recom-
mended that you leave the wrapping on
until later in the installation process.
2
Nylock
Steel
race
3 Locate the 3/8 bolt assembly in the hardware
bag.
4 Remove wrapping from bearing and place the
end of the Elite arm on the wall mount.
5 Pass the 3/8 bolt with the bearing assembly
through the wall mount and the arm from under-
neath. Place the steel race over the bolt inside the arm
as shown and secure rmly with the nylock using the
provided 9/16 wrench and 5 mil hex key.
Note: Keep the
arm folded while
installing.
Elite arm mounted on wall.
6 Extend the arm straight out and lay all of the
cables for your monitor, keyboard, and mouse in
the channel on top of the arm.
Be sure your cables are to
one or the other side of the
center adjustment hub.
Hub
Cable
NOTE: YOU MUST
LEAVE SOME SLACK
IN THE CORDS TO
ALLOW FOR ARM
MOVEMENT.
3
7 Wire tie your cables together with the hub
between them. Wire ties are supplied in the
hardware bag.
8 Add the wire clips to secure the cables. Wire
clips are supplied in the hardware bag.
Wire clips
Add the wire clip to
the end of arm.
Cable
9 Feed cord through the plastic bushing in the
mount assembly. The plastic bushing can be
removed, opened and slipped over cord, if necessary.
10 Replace all of the covers, being sure not to
pinch the cables. The long covers should be
replaced rst, then the center cover, and lastly the two
end covers.
Cable
11 Use the provided 1/4" wrench to open the
plastic slider mount and insert the ball on
the VESA Plate. Tighten rmly.
Be sure to tighten both bolts evenly, each a little at a
time, until fully tightened.
4
14 Attach the optional large handle to the end
of the slider by screwing together the two
halves.
15 Use the slider handle to adjust the monitor
up and down.12 Secure your monitor to the VESA plate using
the 4 provided 4mm screws.
13 Attach the keyboard to the keyboard mount
using the supplied screws.
Slider Handle
16 Lift gently on
the monitor
to release the weight
off the buttons, then
push the buttons to
pivot the monitor
forward and back.
17 Extend the Elite straight out as shown before
adjusting the arms resistance. Be sure all
equipment is mounted on the arm before adjusting.
Adjust the arm closest to the monitor rst.
Use the T-handle provided to
adjust the arm’s resistance.
Note: Before adjusting the tension on your Elite arm,
place everything you are going to mount on it in
place, including the monitor, keyboard, mouse, and
mouse pad.
5
Elite Fine Tilt Adjustment
To make ne adjustments to the horizontal tilt angle
of your monitor and keyboard, use the supplied hex
key and carefully adjust the two screws on either side
of the equipment end of the Elite arm. You will need
to remove the front end cover to access the screws.
Adjustment screw
Hex key
Thank you for your purchase of an ICW Elite arm. Your arm is now ready to use.
Any questions? Please contact ICW at 1-800-558-4435.
elite double arm wall mount rev 6/26/07 dw
Other ICW Rack & Stand manuals
