visplay Mono 20 P/L User manual

play it smart
Mono 20 P/L
Assembly and operating instructions


Mono20P/L
12/2020 (EN)
Table of Contents
1 Safety .......................................................... 3
1.1 Explanation of symbols ...........................................3
1.2 Intended use ............................................................3
1.3 Basic dangers ..........................................................3
2 Product description ...................................... 3
2.1 Overview..................................................................3
2.2 Brief description.......................................................3
2.3 Power supply........................................................... 4
2.4 Scope of supply and accessories........................... 4
3 Assembly.......................................................5
3.1 Unpacking ...............................................................5
3.2 Requirements of installation location......................5
3.3 Reinforcing of panels...............................................5
3.4 Mounting..................................................................5
3.5 Visplay plug system................................................ 7
4 Operation..................................................... 8
4.1 Attaching merchandise support..............................8
4.2 Removing merchandise support .............................8
4.3 Cleaning...................................................................8
5 Dismantling and disposal............................. 9
5.1 Dismantling ............................................................. 9
5.2 Disposal................................................................... 9
6 Technical data .............................................. 9
6.1 Dimensions.............................................................. 9
6.2 Connection values ................................................. 10
6.3 Load values............................................................ 10
These instructions facilitate the safe and eective use
of the “Mono20P/L” product.
These instructions are part of the product and must be
kept safely and in easy reach from the product at all
times.
All persons who use or handle this product must have
read these instructions. Observance of all the safety and
handling instructions given in these instructions are a
prerequisite for safe working.
The figures in these instructions serve for general under-
standing and may dier from the actual version.
All dimensions in these instructions are given in mm.
Quality assurance
All processes in our company are subject to a compre-
hensive management system, which conforms to the qua-
lity standard ISO 9001 and the environmental standard
ISO14001.
The management system is regularly inspected by the
Zertifizierungs- und Umweltgutachter GmbH (BSI), which
documents conformance to the standards by a certifica-
te.
Copyright
These instructions are protected by copyright. Their use
is permitted within the scope of use of the product. Any
use over and above this is only permitted with the written
approval of the manufacturer.
Our General Terms and Conditions of Sale and Supply
are valid for all orders.


Mono20P/L
12/2020 (EN)
1 Safety
Read this manual before using the product for the first
time and proceed accordingly. Keep this manual in a
safe place for later use or to pass on to future owners.
1.1 Explanation of symbols
Warning notices are indicated in this manual as follows.
WARNING
A warning notice designated in this manner indica-
tes a dangerous situation that could result in death
or serious injury if it is not avoided.
NOTE
A warning notice designated in this manner indi-
cates a potentially dangerous situation that could
result in material damage or environmental dama-
ge if it is not avoided.
1.2 Intended use
The product is used exclusively for mounting merchandise
supports, on which goods are presented. Merchandise
supports permitted for this purpose are exclusively those
that conform to the specification in these instructions.
In the event of misuse, there is the danger that the
merchandise supports and the electrical devices will
be damaged. This can result in injuries and damage
to the product.
Area of implementation
The product may only be used in the commercial area.
Personnel
These instructions describe the assembly of the holder
set as well as its handling and cleaning. Therefore these
instructions must be handed on to the end user after
assembly of the holder set.
The contents of the section on “Assembly” is directed at
personnel, who undertake the assembly of the holder
sets (e.g. shop fitters).
The contents of the section on “Handling” is directed at
the end users (e.g. sales personnel, visual merchandisers).
1.3 Basic dangers
>Use only approved accessories and electrical
devices.
>Comply with the permitted connection, maximum
load and equipment values.
>Do not lean any ladders against the merchandise
supports.
>Do not load the merchandise supports above the
maximum load capacity.
>Do not place any receptacles, from which fluids
can escape, on the merchandise supports.
>Keep moisture away from current conducting
components.
2 Product description
2.1 Overview
Mono20P/L is a support system that can be selectively
aligned for mounting display supports on which products
are presented.
2
1
Fig. 1: Mono 20 P/L
2.2 Brief description
Contained in the electrified Mono 20 P/L holder set
(Fig. 1/1) is a power element, through which low voltage
power can flow. This allows the use of shelves (Fig. 1/2)
with integrated light fittings for additional illumination of
the positioned goods.
The merchandise supports must be obtained from the
manufacturer. The electrical devices must conform to the
specification given in these instructions. One merchan-
dise support can be hung per holder set.
Holder sets
The holder sets serve for mounting of the merchandise
support. They are available in the following versions:
• Mono20P/L holder set with power cable (Fig. 2/A)
• Mono20P/L holder set, non-electrified (Fig. 2/B)
• Mono20P/L light holder set with power cable
(Fig. 2/C)
• Mono20P/L light holder set, non-electrified (Fig. 2/D)
NOTE
Non-electrified merchandise supports can be
pushed into electrified holder sets without anypro-
blems.
For the holder set mounting in wood see section .
A B C D
Fig. 2: Version of the various holder sets


Mono20P/L
12/2020 (EN)
2.3 Power supply
The 24 V distributor enables power supply to a maximum
of 8 connections, each with a maximum of 2 converters of
75W. The switched input enables the use of a switch.
ø 7.7 mm
NV (24 V)
L = 200 mm
220–240 V
L = 200 mm
Fig. 3: Converter
NOTE
It is imperative to take account of power consump-
tion of the electrical devices.
The dimmer set 318-271.19 is required for the use of
dimmers.
For an overview of the electrical connection of the holder
sets and the associated components see the section on
Electrification .
2.4 Scope of supply and accessories
2.4.1 Electrical connection set
The electrical connection set is a standard part of the
electrified holder set. It serves for retrospective electrical
connection of existing non-electrified Mono 20P/L holder
sets.
Included in the electrical connection set is the electrical
connection with the power cable (Fig. 4/1) and 2 counter-
sunk fixing screws M5 x 16 Torx (Fig. 4/2).
1
2
Fig. 4: Electrical connection set for non-electrified holder sets
For mounting the electrical connection set see section
3.4.2
2.4.2Cover clip
Fig. 5: Cover clip
The cover clip must be ordered separately.
2.4.3 Merchandise supports
The merchandise supports are used for displaying goods.
Merchandise supports can have dierent shapes.
Examples of merchandise supports available:
• Hanging arms, straight
• Shoe shelves
-for a single shoe or a pair
-electrified or non-electrified
• Mounting bracket for wooden or glass shelf
• Support bar in connection with mounting bracket
• Single support bar
• Universal bracket Drawing no.:
991-217 Wooden shelf 22 mm
• Pair of brackets Ø 20 mm 704-396 Wooden shelf
Further information on the individual merchandise sup-
ports as well as the specific product descriptions can be
found in the product catalogue.
Mounting brackets and shelves
Mounting brackets are for mounting support bars
orshelves.
Shelves are trays or racks made of wood or glass. Cons-
truction drawings for the shelves are available to down-
load from the product section at www.visplay.com.
2.4.4Hanger sets for wooden panels, etc.
2
1
Fig. 6: Hanger sets for wooden panels
Instead of merchandise supports, wooden panels and
placards, etc., can be fixed in the holder set with a
hanger set. This consists of hanger adapter (Fig. 6/1) and
hanger bracket (Fig. 6/2).
• Maximum load: 20 kg


Mono20P/L
12/2020 (EN)
3 Assembly
WARNING
The system can fail if assembly is not carried out
correctly or the base cannot support the necessary
load. There is a danger of injury from goods or mer-
chandise supports falling down.
>Note and comply with all the following instruc-
tions on assembly.
>Make sure that the base is suitable for the ex-
pected loads.
3.1 Unpacking
Immediately on receipt, check the delivery is complete
and intact.
If transport damage is noted, proceed as follows:
• Do not accept delivery or only under reservation.
• Make a note of the extent of the damage on the trans-
port documents or the delivery note of the transport
company.
• Initiate a complaint.
Packaging
The product is securely packed so that transport damage
is unlikely.
• Store original packaging for subsequent transport.
• Only send product in original packaging.
• Take note of all instructions which are given on the
packaging.
Disposing of packaging materials
If the packaging materials are no longer required, dis-
pose of them according to local disposal regulations.
3.2 Requirements of installation location
The installation location must comply with the following
requirements:
• The installation location must be dry. Construction
outdoors is not permitted.
• The base (walls, columns, etc.) must be designed for
and able to support the loads to be borne.
• The base must be level in order that the holder sets are
fully supported after mounting.
3.3 Reinforcing of panels
The panels, in which the holder sets are mounted, must
be reinforced. Otherwise the panels, together with the
mounted holder sets, may buckle andbreak.
A B
19
min. 60
min. 2219
min. 60
min. 28.5
Fig. 7: Back panel reinforcement
Possible reinforcements:
• Angle sections (Fig. 7/A). Take note of the dierent
heights of the holder sets (whether electrified or
non-electrified).
• Wooden ribs (Fig. 7/B)
• Screw reinforcement on to the rear side of the panels
and additionally glue wooden ribs. Make sure that the
panels are supported evenly.
3.4 Mounting
WARNING
If fixing points are left out, the load carrying
capacity of the holder sets provided for will not be
achieved.
>Use all fixing points of the holder sets.
>Ensure the correct alignment of the holder sets.
Fig. 8: Correct alignment of the holder sets
The fixing points, on which the holder sets are to be
screwed, are prepared. The holder set is marked on the
rear side with an arrow and the marking “UP” (Fig. 8).


Mono20P/L
12/2020 (EN)
3.4.1 Mounting holder set on wood
When using the fixings supplied, the holder set must only
be mounted on wooden panels that are 19mm thick.
The holder sets can be used both with or without the
cover clip. Pay attention to the dierent milled form.
A B
Fig. 9: Milled form without (a) and with cover clip (B)
Mounting for the non-electrified holder sets (Fig. 10/A) is
identical to mounting for the electrified holder sets (Fig.
10/B).
1. Arrange for wooden panels with a milled form (see
chapter 6.1) to be fabricated by a specialist works.
2
1
A B
2
1
Fig. 10: Mounting on wooden panel
2. Apply holder set (Fig. 10/1).
3. Screw the wood screws (Fig. 10/2), through the holes
provided in the holder set, into the panel and tighten
to 3 Nm.
ÂThe holder set is fixed.
Attaching cover clip
If the version with cover clip has been selected, the cover
clip must finally be attached after mounting the holder
set.
1
2
Fig. 11: Attaching cover clip
• Place the cover clip (Fig. 11/1) on the holder set
(Fig. 11/2).
3.4.2 Holder sets to be retrospectively electrified
By using the electrical connection set 332-259.19, a non-
electrified holder set (Fig. 12/A) can be retrospectively
electrified (Fig. 12/B). The holder set does not need to
be dismantled from the wooden panel for this procedu-
re. Access to the back of the panel, however, must be
ensured.
A B
Fig. 12: Holder set, non-electrified (A) and electrified (B)
Removing cover panel
1
3
2
4
Fig. 13: Unscrewing cover panel
1. Loosen both screws (Fig. 13/1) with a Torx screwdriver.
The screws and cover panel (Fig. 13/2) are no longer
required and can be disposed of.
2. Fix the electrical connection set (Fig. 13/3) with the
supplied countersunk screws (Fig. 13/4) to the holder
set.
ÂThe holder set is electrified and can now be con-
nected to the power supply.


Mono20P/L
12/2020 (EN)
3.5 Visplay plug system
NOTE
It is imperative to take account of power consump-
tion of the electrical devices! The power consump-
tion of all electrical devices should be below the
nominal output rating of the converter. It is gene-
rally recommended to factor in a power reserve for
additional electrical devices.
31 2
UK
EU
4
2 134
2 135
UK
EU
5
Powering with 2x90W converters (max. 180W)
Operation with 90 W converter
1 Extension cable 24VDC
2 24VDC distributor, 8-way
3 90WLED converter
4 Supply lead 220–240VAC
5 220-240VAC distributor, 4-way


Mono20P/L
12/2020 (EN)
4 Operation
WARNING
Injury can be caused and the merchandise supports
and/or system can be damaged if the maximum
load of the merchandise supports is exceeded.
>Observe the maximum load values of the individ-
ual merchandise supports.
>Do not exceed the maximum load of 40 kg per
holder set.
4.1 Attaching merchandise support
To insert the merchandise support, proceed as follows.
1 2
Fig. 14: Inserting merchandise support
1. Feed the merchandise support with a slight upward
angle into the hole of the holder set up to the stop
(Fig. 14/1), and then lower (Fig. 14/2).
2. Make sure that the merchandise support is correctly
engaged in the holder set.
ÂThe merchandise support is securely fixed. It has
a slight slope (approx. 1.5°).
3. Place goods evenly on the merchandise support
and ensure that the maximum load is not exceeded.
All load values are inclusive of the weight of the mer-
chandise support.
4.2 Removing merchandise support
To remove the merchandise support, proceed as follows:
1. Remove goods from the merchandise support.
2. If a shelf is used, remove the shelf from the mounting
bracket.
1 2
Fig. 15: Removing merchandise support
3. Slightly lift up the merchandise support/mounting
bracket (Fig. 15/1) and pull away from the holder set
(Fig. 15/2).
ÂThe merchandise support comes away from the
holder set.
4.3 Cleaning
During the course of time, dust and deposits from clothes
hangers can settle on the merchandise supports. In order
that the goods on display do not become soiled, the
merchandise supports must be regularly cleaned.
Fig. 16: Cleaning
1. Remove goods from the merchandise support.
2. Remove dirt on the merchandise support carefully
with a soft, dry cloth (Fig. 16).
3. Remove stubborn dirt with a mild cleaning agent.


Mono20P/L
12/2020 (EN)
5 Dismantling and disposal
5.1 Dismantling
To dismantle the holder set, proceed as follows:
1. Remove goods from the merchandise supports.
2. Remove all merchandise supports (see section 4.2).
1
2
Fig. 17: Levering o cover clip
3. Lever o cover clip (Fig. 17/1) with a small slotted
screwdriver (Fig. 17/2). The cover clip cannot be
reused and must be replaced.
4. Unscrew screws.
5. Take o holder set.
5.2 Disposal
NOTE
If product components are improperly disposed of
they can pose a danger to the environment.
>Ensure product components are disposed of in a
proper environmental manner or through waste
management specialists.
>Send components that can be recycled for recy-
cling.
Disposal rules
Dispose of product components in line with the following
principles:
• Send steel for recycling or scrapping.
• Send aluminium for recycling or scrapping.
• Send die cast zinc for recycling or scrapping.
• Send plastics for recycling.
• Dispose of remaining components sorted according to
the type of material.
6 Technical data
6.1 Dimensions
6.1.1 Installed dimensions, holder set
Mono 20 P/L
1928.5
60
ø 31.9
1922
100
A B
Fig. 18: Mono 20 P/L with power cable(A) / non-electrified (B)
Mono20P/L light
1928.5 1922
50
ø 31.9
86
A B
Fig. 19: Mono20P/L light with power cable(A) / non-electrified (B)
6.1.2 Milled form for holder set with cover clip
Mono 20 P/L
5019
6
ø 2.5
2424
35.232.822
68
90
ø 32
50
Fig. 20: Mono20P/L with cover clip


Mono20P/L
12/2020 (EN)
Mono 20 P/L light
38
19
6
ø 2.5
53
672
ø 32
Fig. 21: Milled form for Mono20P/L light with cover clip
6.1.3 Milled form for holder set without cover clip
Mono 20 P/L
ø 26
15 0
+0.2
5019
6
ø 2.5
2424
35.232.822
68
90
ø 32
50
Fig. 22: Mono20P/L without cover clip
Mono 20 P/L light
38
53
672
ø 26
15 0
+0.2
19
6
ø 2.5 ø 32
Fig. 23: Mono20P/L light without cover clip
6.1.4 Converter dimensions, dependent on power
output
L = 200190 22
65
L = 200
Fig. 24: Converter dimensions
6.2 Connection values
General
Specification Value Unit
Operating voltage 100 –240 V AC
Frequency 50– 60 Hz
Nominal voltage (SELV) 24 V DC
Nominal supply current, maximum 7
168
A
W
Mains protection class; converter
10– 150 W
III
Maximum casing temperature
(converter)
90 °
6.3 Load values
The maximum load applies including the dead weight
and the weight of all components.
Holder set
Specification Value Unit
Mono20P/L holder set 40 kg/holder set
Mono20P/L light holder set 8 kg/holder set
Merchandise supports
Specification Value Unit
Shoe shelf for one shoe 20 kg
Shoe shelf for a pair of shoes 20 kg
Universal mounting bracket 20 kg
Hanger arm Ø 20 mm 20 kg
Single support bar Ø 20 mm 15 kg
Mounting bracket for support bar
Ø 20 mm
15 kg
Mounting bracket for wooden
or glass shelf
15 kg
Mounting bracket for support bar
30 x 15 mm
20 kg
Clamping mounting bracket
for glass shelf
10 kg
Single mounting bracket Ø 20 mm 15 kg
Hanger set for wooden panel 20 kg
Mounting bracket for wooden shelf 15 kg
Hanger hook Ø 6 mm 2 kg
Hanger hook Ø 7.5 mm 2 kg
Panel thickness
Specification Value Unit
Wooden panel thickness 19 mm