Unicol WB0 User manual

WARNING
Please carefully inspect the product before assembling. If you notice any apparent damage, call your carrier
claims agent and do not continue the installation until it has been reviewed. Please watch for pinch points.
Do not put your fingers between moveable parts. Do not tamper with or disassemble any spring loaded
parts. Before installing, make sure that the supporting surface will support five times the combined load of
the solution and the hardware. Never exceed the maximum load capacity. Please also layout all components
to ensure that you have all of the required parts before proceeding (see BOM list on following page). Use of
this product for anything other than its specified use may result in failure or personal injury. This product is
intended for indoor use only. We recommend using a qualified trades person for installation. Use an assistant
or lifting equipment to lift and position products.
For support, please call: [phone] or email: [e-mail]
Revised 29/09/22
01865 767676
[e-mail]
www.unicol.com
*Please check model specific details before installing*
Wall Arms – Fixed - WB - 0,02,1&2
Guide Max. Weight: 60kg
WB1
WB02
WB0
WB2

2Revised 29/09/22
COMPONENTS
01865 767676
[e-mail]
www.unicol.com
INSTALLERS REQUIRED
1-2
#TOOLS REQUIRED
13/16th Allen Key
2Pozidrive Screwdriver
3
4
5
# DESCRIPTION QTY
1WB02 - Socket Version 1
# DESCRIPTION QTY
1WB0 - Peg Version 1
# OPTIONAL EQUIPMENT QTY
1Column 1
1Projector Suspension Unit – PSU 1
1Screen Mount Adapter – (PS1 shown) 1
# OPTIONAL EQUIPMENT QTY
1Projector Suspension Unit – PSU 1
1Screen Mount Adapter – (PS1 shown) 1
# DESCRIPTION QTY
1WB2 - Socket Version 1
# DESCRIPTION QTY
1WB1 - Peg Version 1

01865 767676
[e-mail]
www.unicol.com
3
Revised 29/09/22
STEP 1 – (WB, 0, 02, 1 & 2)
Determine where you want to install your wall arm.
Mark and fix into position through the six fixing holes
using suitable anchors & screws.
Please consider cabling and wall fixings prior to
installation. Please check surface is capable of
supporting 5x the combined solutions weight.
STEP 2 – (WB, 0 & 1)
Unscrew Through-Bolt located on the socket of the
PSU. Locate socket onto the Peg of the Wall Arm and
push upwards. Refit Through-Bolt ensuring it locates
through the peg of the Wall Arm.
STEP 3 – (WB, 0 & 1 )
Unscrew Through-Bolt located on the socket of the
Screen Mount Adapter. Locate socket onto the Peg of
the Wall Arm and push upwards. Refit Through-Bolt
ensuring it locates through the peg of the Wall Arm.
STEP 4 – (WB, 0 & 1 )
Fully tighten Through-Bolts. Take up any slack using
grub screws in sockets.
Cable along wall arm & apertures in Screen Mount
Adapter & PSU sockets.
Follow PZX/W, PLX/W Instructions to fit Screen.
Follow PSU Instructions to fit Projector.
WB, 0, 02, 1 & 2 Wall Fixing WB, 0 & 1 – Adding PSU
WB, 0 & 1 – Adding Screen Mount Adapter
Typical Screen
Mount Adapter
PS1 shown
Typical
PSU
shown

4Revised 29/09/22
01865 767676
[e-mail]
www.unicol.com
STEP 1 – (WB, 02 & 2)
Unscrew Through-Bolts located on the sockets of
the Wall Arm and PSU. Place column onto the Peg of
the Wall Arm and push upwards. Refit Through-Bolt
ensuring it locates through the peg of the Wall Arm.
Repeat this operation to join the PSU to the other end
of the column.
STEP 2 – (WB, 02 & 2)
Fully tighten both Through-Bolts. Take up any slack
using grub screws in socket.
Cable through column and apertures in Wall Arm &
PSU sockets.
Follow PSU Instructions to fit Projector.
STEP 1 – (WB, 02 & 2)
Unscrew Through-Bolts located on the sockets of the
Wall Arm and Screen Mount Adapter. Place column
onto the Peg of the Wall Arm and push upwards. Refit
Through-Bolt ensuring it locates through the peg of
the Wall Arm. Repeat this operation to join the Screen
Mount Adapter to the other end of the column.
STEP 2 – (WB, 02 & 2)
Fully tighten both Through-Bolts. Take up any slack
using grub screws in socket.
Cable through column and apertures in Wall Arm &
Screen Mount Adapter sockets.
Follow PZX/W, PLX/W Instructions to fit Screen.
WB, 02 & 2 – Adding PSU & Column
WB, 02 & 2 – Adding Screen Mount Adapter & Column
Typical
PSU
shown
Typical Screen
Mount Adapter
PS1 shown