visplay Stripes User manual

play it smart
Stripes
Assembly and operating instructions
USA & CANADA

2
General Instructions
1/2019 (US)
Visplay products are manufactured according to the
latest technology and comply with valid rules and
regulations.
Nevertheless, these products can cause injury or
damage if:
• the product is improperly installed
• the product is improperly used
• the product is improperly altered or modified
• original accessories are not used
• the safety regulations are not observed.
⚠WARNING
Each person involved in the planning, installation
and/or use of our products must be carefully read
and observe these instructions of use.
The following are of course also valid:
• Relevant accident prevention regulations
• Generally recognized safety rules
• National regulations – please consult Visplay if there
is a discrepancy with the Assembly manual
Safety instructions
⚠WARNING
When playing, children often incorrectly assess
danger. You must therefore make sure that your
store fittings are not used as toys.
Please pay attention to the following points:
• Structural conditions, in particular the design and
bearing capacity of walls, ceilings and floors. If
bearing capacity for the specified tractive or pressure
load cannot be achieved by suitable fastening or
stabilising elements, please refrain from installation.
• All the structural components supplied for stabilising
structures are to be used in an unrestricted manner
and must not be removed.
• The products may only be loaded after all the
installation steps have been completed.
• Merchandise supports should be loaded as evenly as
possible.
• Avoid loading in fits and starts.
• The maximum weight loads is to be observed. This can
be found in the instructions on assembly and use, as
well as in our sales documentation.
• Furniture with castors is generally much more unstable
than furniture with glides. Tall, heavy structures on
castors should thus be avoided.
• The recommendations of your safety ocer should
also be observed.
General care for chrome, silk and pearl
In clothing retail applications, frequent dragging of
clothes hangers along the surface can cause slight
abrasion to their hooks. This eect is most pronounced
- more so than with front-on horizontal or inclined-pole
displays - where garments are hung side-on such that
hangers have to be moved more frequently. To prevent
garments from becoming soiled, cleaning of the hanging
rods is essential.
This abrasion can be considerably reduced by using a
coat hanger cover (scliss, 929-449.02).
No responsiblity can be accepted for damage caused by
soiling, as the above mentioned abrasion depends on the
material of the coathangers in use.
With powder-coated surfaces subject to frequent use,
use of special paints is recommended. We will be happy
to advise you.
Use and care of merchandise supports with
anodised aluminium surfaces
Visplay merchandise supports with anodised aluminium
surfaces are hard-wearing. However, the exchange of
accessories might cause slight marks on the surface.
Accessories with plastic inserts usually cause less wear or
none at all.
To remove the marks, we recommend using cleaning
agents ranging from pH 5–8 (do not use any detergents
with acidic or alkaline reaction). Clean by washing the
surfaces using a sponge and water containing a wetting
agent. Then remove any loose or greasy dirt. Rubbing
o the surfaces with detergent using pure cotton waste
or porous cleaning tissue and applying the necessary
pressure in rubbing direction will remove the marks.
Aluminium profiles with widths exceeding 200 mm/
7.874" must be subjected to abrasive cleaning using
detergents specifically developed for this purpose. The
cleaning agents developed for abrasive cleaning contain
very finely ground neutral polishing agents and have to
be adapted to the oxide layer. Alternatively, cleaning
can be carried out using an abrasive fibrous web (e.g.
Scotch-Brite, type A, red, fine or very fine) in combination
with a non-abrasive detergent.
Subsequently, residual cleaning agents should to be
rinsed o using a sponge and clear water. Then rub o
the part with a chamois.
Copyright
This manual is protected by copyright. Its use is
permissible as part of the use of the product. Any use
other than this is not permitted without written consent of
the manufacturer.
Our General Terms and Conditions apply for all orders.
www.visplay.com | r[email protected]
Dimensions are generally shown in millimeters and
inches.

3
Stripes 13
7
0.276"
7
0.276"
42
1.654"
L
19.5
0.768"
19.5
0.768"
71
2.795"
L = 3100 mm/122"
lto = min. 250 max. 3100 mm/
min.10" max. 122"
L = 56 mm/2.205" L = 110 mm/4.331"
L
L
lto
26
1.024"
( 26 )
(1.024")
76.2
3" 40 x 76.2 = 3048
40 x 3" = 120"
X X76.2
3"
1/2019 (US)
Assembly dimensions / Layout
The choice and arrangement of the profiles must be adapted to the respective assortment and expected load.
Stripes can be fixed on to curved panels (radius > mm/"). Profile cannot be pre-curved.
Please observe the indications concerning weight loads and ensure that the substructure of the wall units/furniture and their fixtures can
support the expected loads.
With free-standing furniture, ensure that there is sucient stability even with the intended merchandise supports.
When installing in glass, safety glass must be used.
Distance of holes
Assembly dimensions Stripes13
Wood: mm/"
Safety glass: min.  mm/"
Rabbet size for wood Rabbet size for glass
Layout
Panels and sub-structures must be toughened against bowing. Wooden ledges or angle
sections are suitable for this purpose.
glued and screwed

4
Stripes 13
max. 2 Nm
40
1.575"
R min. 6m
19‘ 8"
1/2019 (US)
Assembly instructions
Stripes profiles will be screwed.
Please note that the attachment exerts pressure
and friction on soft wall types (e.g. textured wall-
paper) and can damage them.
Stripes can be attached on curved walls (radius
> mm/"). Profile cannot be pre-curved.
The torque must be observed to ensure the
correct functioning of Stripes13.
Fixing set for Stripes profiles
To be screwed to the back of wooden panels.
Examples on wooden panel
Examples on glass panel

5
Stripes 13
1.5°
625
24.606"
70
2.756"
45
1.772"
589
23.189"
1250
49.213"
1245
49.016"
Side hanging frame Ø 25 / 0.984"
987-048.48
Bracket for side hanging rail
Side hanging rail Ø 25 / 0.984"
620
24.409"
987-048.48
1/2019 (US)
Instructions of use
With Stripes, the suspension arm of the merchandise support is inserted into the profile at an angle and then lowered down.
Merchandise support slightly inclined (°).
The indicated weight loads are always based on the total weights of the merchandise support and goods.
Please observe that max. weight loads decreases as the merchandise support increases in length.
Please observe that the inclination of the merchandise support changes with an increase in load. Dierent weights on the merchandise
supports produce an uneven overall appearance of the goods display.
Please note that the weight limit can reduce considerably when Stripes 13 is used in glass and sheet metal.
Please also observe the weight loads indicated in our sales documentation.
Weight loads
Bracket for wooden or glass shelf 987-048.48 with side hanging frame or with bracket for side hanging rail
Max. load
Profile per 625 mm/25"  lbs
Short profile 44 lbs
Front arm Ø 25 mm/1"  lbs
Bracket 30 x 5 mm/13⁄16" x 3⁄16" for side hanging rail Ø 25 mm/1"  lbs
Side hanging frame Ø 25 mm/1"  lbs
Bracket 30 x 5 mm/13⁄16" x 3⁄16" for wooden or glass shelf  lbs
Front arm Ø 12 mm/½"  lbs
Bracket Ø 12 mm/½" for side hanging rail Ø 15 mm/5⁄8" lbs
Bracket Ø 12 mm/½" for wooden shelf  lbs
Clamping bracket for glass shelf  lbs
Hat bar Ø 12 mm/½"  lbs
Hook Ø 7.5 mm/9⁄32" lbs
Shoe shelf  lbs
Fixing set  lbs

6
Stripes 16
13
0.512"
17
0.669"
L =3100 mm/122"
lto =min. 250 max. 3100 mm/
min. 10" max. 122"
Dim X =
lto– –1
2
x 76.2
round up to a hole number
76.2
lto
L
lto
25
1"
( 27 )
(1.063")
76.2
3" 40 x 76.2 = 3048
40 x 3" = 120"
X X76.2
3"
1/2019 (US)
Assembly dimensions / Layout
The choice and arrangement of the profiles must be adapted to the respective assortment and expected load.
Stripes can be fixed on to curved panels. The profile must be pre-curved for radii between  mm/" and mm/". With radii >
mm/" it is not necessary to pre-curve profiles.
Please observe the indications concerning weight loads and ensure that the substructure of the wall units/furniture and their fixtures can
support the expected loads.
With free-standing furniture, ensure that there is sucient stability even with the intended merchandise supports.
Distance of holes
On-site masonry
Assembly instructions
With radii greater than mm/",
pre-curving is not necessary.
Inner radius
Ri >  m/‘ " Outer radius Ra >  m/‘ "

7
Stripes 16
18.9
0.74 4"
59.5
2.343"
100
3.937"
100
3.937"
25
0.984"
(75)
(2.953")
ø5.2
0.205"
8.5
0.335"
3100 mm/122"
lto =min. 250 max. 3100 mm/min.10" max. 122"
min. 50
1.969”
min. 50
1.969”
WoodGypsum
ConcretePorous materialMetal (square tube)
20.2
0.795"
17
0.669"
1/2019 (US)
Dimensions Stripes 16 profile for attachment from the front, for walls (gypsum/drywall, concrete, brick, wood)
Dimensions of holes for Stripes 16 profile for attachment from the front
All fixation points are to be used with maximum loads.
• Fastening examples
Depending on the type of wall the profil can be attached with dierent
fixation material.
The max. weight load of the Invisible  P/L profile depends on the
nature of the wall, on the number of fixation points as well as on the
fixation material used.
With wooden substructures, a screw length of min.  mm/"
must be observed.
For mounting on plaster, the following dowels are recommended
(manufacturer Hilti):
• Hollow toggle plug HTB-S Mx
• Hollow plug HHD-S M/x
Please observe the information on the loading values and ensu-
re that the substructure of the wall installation and its fastenings
can cope with the expected loads.
>The correct size and type of anchor fixings must be used to suit
the construction conditions.
>Check anchor fixing as specified by manufacturer.
>All mounting points must be used.

8
Stripes 16
M5
ø 12
0.472"
80
3.150"
60
2.362"
16–21
0.630"–0.827"
52
2.047"
929-178.21
929-180.05
max. 2 Nm
ø 12
0.472"
Set 929-187.21
Profile cover
10
0.394”
12
0.472”
ø 10
0.394”
17
0.669”
1/2019 (US)
The Stripes Profile must be fitted immediately after the adhesive
has been applied. The screw can then be turned in the liquid -
and not hardened - adhesive.
Please observe correct assembly.
Additional use of Fischer® (www.fischerfixings.com) adhesive
enables full weight loading - once it has hardened.
Assembly wooden panel
For front attachment to cavity walls, the
fixing set - is to be used.
• Drill Ø mm/" hole.
• Insert cavity dowel (fixing set -) using pliers (Recommendation: Metal cavity fixing HM z from Fischer® - www.fischerfixings.com) and
expand.
• Unscrew the pre-assembled screw.
• Add Stripes profile and secure with aforementioned screw.
• Assembly has been correctly completed when the screw has been tightened up as far as possible ( Nm).
When using the fixing set (929-178.21), the max.
permissible weight per front arm is reduced to 33 lbs.
Assembly glass
A special fixing set (929-187.21) is to be used for assembly on
tempered glass..

9
Stripes 16
max. 2 Nm
1.5°
40
1.575“
1/2019 (US)
Instructions of use/ Care
With Stripes, the suspension arm of
the merchandise support is inserted
into the profile at an angle and then
lowered down.
Merchandise support slightly incli-
ned (°).
The indicated weight loads are always based on the total weights of the merchandise support and goods.
Please observe that max. weight loads decreases as the merchandise support increases in length.
Please observe that the inclination of the merchandise support changes with an increase in load. Dierent weights on the merchandise
supports produce an uneven overall appearance of the goods display.
Please note that the weight limit can reduce considerably when Stripes 16 is used in glass and sheet metal.
Please also observe the weight loads indicated in our sales documentation.
Weight loads
Fixing set for Stripes profiles
To be screwed to the back of wooden panels.
Assembly instructions
Stripes  profiles will be screwed.
Please note that the attachment exerts
pressure and friction on soft wall types (e.g.
textured wallpaper) and can damage them.
The torque must be observed to ensure
the correct functioning of Stripes16.
Max. load
Profile per 625 mm/25"  lbs
Fixing set  lbs
Front arm Ø 25 mm/1"  lbs
Front arm Ø 12 mm/½"  lbs
Bracket for side hanging rail Ø 25 mm/1" per bracket  lbs
Bracket for wooden or glass shelf per bracket  lbs
Side hanging frame Ø 25 mm/1"  lbs
Side hanging rail, T arm Ø 15 mm/5⁄8",  mm/153⁄8"  lbs
Bracket Ø 12 mm/½" for side hanging rail Ø 15 mm/5⁄8"per bracket  lbs
Bracket Ø 12 mm/½" for wooden shelf per bracket  lbs
Bracket Ø 15 mm/5⁄8" for wooden shelf, concealed per bracket  lbs
Clamping bracket for glass shelf per bracket  lbs
Hat bar Ø 12 mm/½"  lbs
Hook Ø 7.5 mm/9⁄32" lbs
Shoe shelf  lbs

Visplay Companies
Oces & Showrooms
Visplay Exclusive Dealers / Sales Agents /
Authorized Distributors
Australia
Distributed by MADE Retail Systems
Authorized Distributor
2 Stephenson Street
Cremorne Vic 3121
Melbourne
Australia
T [phone]
[e-mail]
Brazil
Distributed by Instant Shop
Authorized Distributor
Av. Nove de Julho, 5017 # 51
Cj. 51 - 5° Andar
São Paulo, SP - CEP 01407-200
Brazil
T [phone]
[e-mail]
China
Distributed by Okamura Shanghai
Authorized Distributor
15Fax: B block, FutureLand building
No.5 Lane 388, Zhongjiang Road
Putuo District
Shanghai 200062
China
T [phone]
[e-mail]
Greece
Distributed by KYVERNITIS I. SA
Exclusive Dealer
125, G. Papandreou & Adrianiou str.
144 51 Metamorfosi Athens
Greek
T [phone]
[e-mail]
India
Distributed by
Matrix Visual Innovations Pvt. Ltd.
Authorized Distributor
45/1, 2nd Floor, Corner Market,
Malviya Nagar
New Delhi 110017
India
T [phone]
[e-mail]
Italy
Distributed by Zeppelin s.r.l.
Exclusive Dealer
Via Matteucci, 2
61032 Fano PU
Italy
T [phone]
[e-mail]
Japan
Distributed by
Okamura Corporation
Exclusive Dealer
Higashi Ote Bldg.,
1F1-1-7, Uchikanda, Chiyoda-ku
Tokyo 101-0047
Japan
T [phone]
[email protected]
Panama
Distributed by Vidisplay S.A.
Authorized Distributor
Calle Ramon Jurado,
Paitilla Mall, Local 17 Piso 1
Punta Paitilla
Panama
Ciudad de Panamá
T [phone]
[e-mail]
Poland, Czech Republic & Baltics
Distributed by
Meškank Interior Brands
Sales Agent
T [phone]
[e-mail]
Russia
Distributed by ULTIMATHULE
Exclusive Dealer
Business quartel „ARMA“
Nizhniy Susalniy per., 5 bld.18
105065 Moscow
Russia
T [phone]
[email protected]
Saudi Arabia
Distributed by Saudi TKT
Authorized Distributor
P.O. Box 10700
Jeddah 21443
Saudi Arabia
T [phone]
[e-mail]
Turkey
Distributed by
Dekotek Mimarlık Ltd. Sti
Exclusive Dealer
Sair Nigar Sokak 80/8 Osmanbey
34363 Istanbul
Turkey
T [phone]
[e-mail]
For other countries:
Visplay GmbH
Charles-Eames-Str. 2
79576 Weil am Rhein
T [phone]
[e-mail]
Austria
Visplay Austria
Schottenring 12
1010 Wien
Austria
T [phone]
[e-mail]
Belgium
Visplay Belgium
Woluwelaan 137
1831 Diegem
Belgium
T [phone]
[e-mail]
France
Visplay France
So Square Opéra
5, Rue Boudreau
75009 Paris
France
T [phone]
[e-mail]
Germany
Visplay GmbH
Charles-Eames-Strasse 2
79576 Weil am Rhein
Germany
T [phone]
[e-mail]
Germany Showroom
Visplay GmbH
Charles-Eames-Strasse 2
79576 Weil am Rhein
Germany
T [phone]
[e-mail]
Netherlands
Visplay Netherlands
De Oude Molen 2
1184 VW Ouderkerk aan de Amstel
Netherlands
T [phone]
[e-mail]
Spain / Portugal/ Latin America
Visplay Spain
Calle Padilla, 21
28006 Madrid
Spain
T [phone]
[e-mail]
United Arab Emirates
Visplay GmbH (Dubai BR)
Sheikh Zayed Road
P.O .B ox : 2 1 3 0 3 5
Sheikha Sana Mana
Al Maktoum Building
Oce - M 10
Dubai
T [phone]
[e-mail]
United Kingdom
Visplay United Kingdom
30 Clerkenwell Road
London EC1M 5PG
United Kingdom
T [phone]
[e-mail]
USA
Visplay Inc.
7528 Walker Way
Allentown, PA 18106
USA
T [phone]
[e-mail]