Vista QSW16M User manual

1
QSW16M User manual V1.0
QSW16M
16 Chn PoE managed switch

2
QSW16M User manual V1.0
Before You Begin
Read these instructions before installing or operating this product.
Note: This installation should be made by a qualified service person and should conform to local codes.
This manual provides installation and operation information. To use this document, you must have the following minimum
qualifications:
• A basic knowledge of CCTV systems and components
• A basic knowledge of electrical wiring and low-voltage electrical connections
Intended use
Only use this product for its designated purpose; refer to the product specification and user documentation.
Customer Support
For assistance in installing, operating, maintaining and troubleshooting this product refer to this document and any other
documentation provided. If you still have questions, please contact Norbain Technical Support and Sales:
Norbain SD, 210 Wharfedale Road, IQ Winnersh, Wokingham, Berkshire RG41 5TP, England.
UK [phone]
Note: You should be at the equipment and ready with details before calling Technical Support.
Conventions Used in this Manual
Boldface or button icons highlight command entries. The following WARNING, CAUTION and Note statements identify
potential hazards that can occur if the equipment is not handled properly:
* WARNING:
Improper use of this equipment can cause severe bodily injury or equipment damage.
* CAUTION:
Improper use of this equipment can cause equipment damage.
Note: Notes contain important information about a product or procedure.
This apparatus is manufactured to comply with the radio interference.
A Declaration of Conformity in accordance with the following EU standards has been made. The
manufacturer declares that the product supplied with this document is compliant the provisions of the EMC
Directive 2004/108/EC, the CE Marking Directive 93/68 EEC and all associated amendments.
All lead-free products offered by the company comply with the requirements of the European law on the
Restriction of Hazardous Substances (RoHS) directive: 2011/65/EU, which means our manufacture
processes and products, are strictly “lead-free” and without the hazardous substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be
collected separately at the product end-of-life. This applies to your product and any peripherals marked
with this symbol. Do not dispose of these products as unsorted municipal waste.
* This symbol indicates electrical warnings and cautions.
** This symbol indicates general warnings and cautions.
NORBAIN SD reserves the right to make changes to the product and specification of the product from time to time without
prior notice.

3
QSW16M User manual V1.0
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL .
WARNINGS AND CAUTIONS:
To reduce the risk of fire or electric shock, do not insert any metallic objects through the ventilation grills or other openings
on the equipment.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from
the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Unplug this apparatus during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
13. CAUTION –THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE
RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING
INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.
14. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.
15. ITE is to be connected only to PoE networks without routing to the outside plant.
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

4
QSW16M User manual V1.0
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Contents
1.Introduction................................................................................................................................................5
1.1 Overview.............................................................................................................................................5
1.2 Product Features.................................................................................................................................5
1.3 Front panel..........................................................................................................................................5
2 Installation.................................................................................................................................................6
2.1 Contents .............................................................................................................................................6
2.2 Installation requirements.....................................................................................................................6
2.3 Rack mount.........................................................................................................................................6
2.4 Desk mount........................................................................................................................................7
2.5 Wall mounting.....................................................................................................................................7
2.6 Cable connections...............................................................................................................................8
2.6.1 Configuration cable.......................................................................................................................8
2.6.2 Power connection.........................................................................................................................8
3. PoE Web Page management ...................................................................................................................9
3.1 Connection to web page......................................................................................................................9
3.2 Switch IP address change.................................................................................................................10
3.2 Password change..............................................................................................................................10
3.3 Factory defaults ................................................................................................................................10
3.4 Restore IP address and Password....................................................................................................10
3.5 Device information ............................................................................................................................11
4. PoE Power management........................................................................................................................12
4.1 PoE settings......................................................................................................................................12
4.2 Power Status.....................................................................................................................................12
4.3 Port Status and Control.....................................................................................................................12
5. CCTV Mode............................................................................................................................................13

5
QSW16M User manual V1.0
1.Introduction
1.1 Overview
This manual covers the installation set up and use of the QSW16M 16 Chn PoE Switch
1.2 Product Features
16 100Mbps downlink PoE Ethernet ports, 2 x gigabit uplink ports and 1 gigabit fibre port
PoE ports support PoE+ ( Max 30W per channel , total budget 250W)
CCTV Mode –Allows extended PoE and Data ( up to 250M of cat5e cable)
LED indication of Power consumption
Standards: IEEE802. 3、IEEE802. 3u、IEEE802. 3ab、IEEE802. 3af/at
4K MAC address, 2.75Mb cache
Quick installation, easy operation, wall mount, desk or racks mount.
1.3 Front panel

6
QSW16M User manual V1.0
2 Installation
2.1 Contents
Please ensure that all items are present when un-packing the switch
2.2 Installation requirements
The switch should only be installed in an indoor environment , either in a rack mount cabinet, secured to a
wall or desk mounted. The following requirements should be observed:
Leave a minimum of a 10cm air gap to allow sufficient ventilation
The wall or cabinet should be of sufficient strength to support the switch
The Cabinet should be well grounded
2.3 Rack mount
Installation process:
1. Check rack grounding and stability
2. Use the provided screws to fit the connection ears to the switch
3. Use the provided screws to fit the switch in the rack

7
QSW16M User manual V1.0
2.4 Desk mount
The Switch can simply be mounted on a desk or table top, please ensure the environment is stable and
clean.
If required the rack mount ears can be used to secure the switch to the desk top.
2.5 Wall mounting
The switch can be hung on a wall, please ensure the wall is of sufficient strength to support the switches
weight, and that the correct fixings are used for the wall construction.
Procedure:
1. Use the provided screws to fit the connection ears to the switch
2. Use the correct fixings for the wall construction to mount the switch to the wall

8
QSW16M User manual V1.0
2.6 Cable connections
2.6.1 Configuration cable
To configure the PoE settings etc connect a network cable to “PoE managed” port on the front of the
switch.
2.6.2 Power connection
The switch requires 230VAC mains connection. Ensure the power supply conforms to this.
The AC power connection LED will show when power is applied.

9
QSW16M User manual V1.0
3. PoE Web Page management
The QSW16M Web management function allows the operator to control and manage the PoE output of
each of the 16 ports.
3.1 Connection to web page
1. Using a Network cable ( Crossover for direct connection)
2. As default the Switches IP address is 192.168.1.200 (Subnet 255.255.255.0).
3. Ensure that your PC is set to an IP address within the same range as the switch.
4. Open a web browser on your PC ( IE7 or later, Firefox or Chrome
5. Enter the switches IP address within the browser ( 192.168.1.200)
6. The following login page will appear:
7. Default login details are: User –admin, Password –admin.
8. Next click on “Login”, to display the following page:

10
QSW16M User manual V1.0
3.2 Switch IP address change
1. To Change the IP Address of the switch to a logical address for your network, click on “IP” in the
top menu bar, the following menu will be displayed:
2. Change the IP address , Subnet and Gateway to suit the individual network, These address details
should be supplied by the Network manager.
3.2 Password change
For additional security it is advised that the default password is changed. To do this click on “Password” on
the top menu bar, to show the following menu:
Enter the current password, to confirm you are an authorised user, then enter the new password twice.
Finally click “OK”.
3.3 Factory defaults
If it is necessary to default the switch to it’s original settings, click on “Factory Default” in the top menu bar
to display the following menu:
Click on “OK”, wait for 10 seconds. The switch will then be defaulted.
3.4 Restore IP address and Password
If it is necessary to restore the IP address and Password, this can be done using the following procedure:
1. Power up the switch
2. Remove the RJ45 cable form the “PoE Managed” port,
3. Using an appropriate tool, press and hold the “init” button for 5 seconds.

11
QSW16M User manual V1.0
4. The RJ45 LED on the “PoE managed” port will flash once.
5. The IP address and Password are now reset to factory default.
3.5 Device information
To get information on the switches IP address, MAC address and software version, click on “Device info”
on the top menu bar, this will display the following menu:

12
QSW16M User manual V1.0
4. PoE Power management
4.1 PoE settings
(1) Power Provided:
The total power provided by QSW16M PoE switch, i.e. the power provided by the built-in 54V power
supply, has been set up when it leaves the factory, please do not modify it. If users modified the power
supply, please correct this setting. If the setting value is larger than the actual power of the built-in power
supply, this will cause damage to the built-in power supply. If the setting value is smaller than the actual
power of built-in power supply, built-in power supply could not be fully allocated out.
(2) Overload limit:
The built-in power supply allows an overload value setting range of 0%-10%, default is 5%. If actual power
draw is too large that cause built-in power supply to reduce power to the lower priority ports.
(3) Reserved rate
As default 15% of the switches power budget is reserved to compensate for unexpected load changes. This
can be adjusted. The higher the value the lower the risk of system overload.
4.2 Power Status
The power Status shows the current power situation, it gives details of what power is being used, what
extra is available and how much is being held back as reserve.
4.3 Port Status and Control

13
QSW16M User manual V1.0
1. Port number –This refers the individual ports on each switch if this indicates a device is connected
and power is being delivered.
2. Power Device Description –A description of the device attached to each b port can be given
3. Priority –3 levels can be set Low, Medium , high. When a system overload occurs power is turned off to
lower priority devices first.
4. Power Limit –An individual limit can be set for each port.
5. Power Consumed –this is the current power consumption of each port.
6. OK –If the port is operating correctly “OK” will be displayed.
7. Port control ON /OFF
Individual ports can be turned ON or OF by clicking the button . A message will be displayed:
Alternatively ALL the ports can be turned ON or OFF, by clicking on the button, again a message
will be displayed:
5. CCTV Mode
THE QSW16M has a unique “CCTV” mode. This allows the transmission of video and PoE power up to
250m on a Cat5e cable.
The enter this mode simply flick the Switch on the front panel to the CCTV side.
In this mode, there is no interconnection of data between the 16 PoE ports, they can only connect to the
switches Uplink ports.

14
QSW16M User manual V1.0