Vitek VT-5016 BK User manual

ENGLISH

www.vitek.com
INSTRUCTION MANUAL
PORTABLE LCD TFT TV 7”
MODEL VT-5016 BK
3
8
14
20
25
UZ
5016IM.indd 1 21.02.2008 11:25:59

5016IM.indd 2 21.02.2008 11:25:59

ENGLISH

Operating manual
Read this manual carefully before connecting
and setting up this appliance. It is necessary to
follow all the warnings and recommendations
on operating this appliance contained in this
manual.
Keep this manual for future reference.
Safety guards
• In order to avoid electric shock do not try to
open the housing of this appliance.
• Servicing should be undertaken by qualified
professionals at service centers only.
• This appliance should be connected to a
power supply line with voltage 00-240V
and frequency 50-60Hz through an adapter.
Check if the power supply line voltage meets
the adapter’s operating voltage. Use only
the adapter included into the delivery set for
connecting to power supply line.
• In order to avoid fire or electric shock do not
expose this appliance to rain or moisture,
do not allow drops or splashes falling on the
appliance. In order to avoid fire or electric
shock do not store this appliance at any
places with high humidity. It is forbidden to
immerse this appliance into water.
• Install the appliance so that to be able
to disconnect the adapter in case of
malfunction.
• Do not disconnect the adapter when the
appliance is working.
• Install the appliance at the places with
sufficient ventilation.
• Do not place this appliance near heat
sources or at places exposed to direct
sun rays, oil vapors, excessive dusting or
vibration.
• Do not allow any objects falling inside the
appliance through the holes in its housing as
it can lead to fire and electric shock. In case
of such accident disconnect the appliance
from the power supply line and turn to
qualified professionals for consultations
before using the appliance again.
• Do not allow the appliance to fall down.
• Do not expose the appliance to extremely
high or low temperatures. Storage
temperature range is from -40°С up to 60°С,
and operating temperature range is from
-5°С up to 40°С.
• Disconnect from power supply line before
cleaning. Use soft cloth for cleaning the
appliance. It is forbidden using liquid or
aerosol detergents for cleaning.
• Do not use this appliance while driving. Do
not use this appliance at the places where
a driver could see the picture on its display.
This is distracting for the driver, and may
lead to serious accident causing trauma or
property damage.
• Do not press on the appliance’s display. Do
not touch it by any sharp objects as you can
damage it.
Attention! Bright and dark points on the LCD
are not the sigh of TV-set malfunction. This is
the norm of TFT-LCD technology.
Description
. telescopic antenna
2. TFT-LCD display
. button for entering menu MENU
4. button PICT
5. auto search button AUTO
6. operating modes switching button MODE
7, 8.volume adjustment control buttons
VOL + / -
9, 0. channels switching buttons CH + / -
. place of remote control signal photo
receiver
2. button for switching on Power
. jack for connecting the external antennae
4. jack AV In 
5. jack AV In 2
6. jack for connecting head phones
7. jack for connecting AC-adapter DC +2V
8. speaker
Functions of Remote Control Buttons
• Number buttons 0 - 9 and button - / -- are
used for inputting channel number (0- 255).
Input channel number from 0 to 9 using
corresponding button on remote control. If
number is more then 9 first press button - /
--, the corresponding symbol will appear
on LCD. Then dial the channel number by
setting number for each digit using number
buttons.
• СН+ / CH- – buttons for switching between
channels
• VOL+ / VOL - – button for adjusting volume
level
• PICT – using this button you can choose one
of five picture modes: standard, soft, vivid,
light, personal.
5016IM.indd 3 21.02.2008 11:25:59

ENGLISH
4
• POWER ( ) – press this button to switch
between TV-set standby and power off
mode. In game mode press this button to
exit the game.
• MENU – in TV mode: press this button
to enter into the next menus: PICTURE,
OPTION, CLOCK, SYSTEM, PRESET. In
VIDEO mode press this button for entering
the next menus: PICTURE, OPTION,
CLOCK, SYSTEM.
• MUTE ( ) – button for switching the sound
off. Use this button for switching the sound
off, press this button once more or press
button VOL+ to switch sound on again.
• CALL – press this button to display
information about the currently viewed
program/current mode
• TIMER –press this button to set time of TV-
set switching off (20 minutes maximum)
• LANG – press this button to choose on-
screen display language
• CALE – pressing this button you can view
year, month, day, and week. Using buttons
СH+ /CH- you can set year and month by
buttons VOL -◄ / VOL+ ►
• AV - using this button you can switch
between TV/video modes
• AUTO - keep this button depressed for 
seconds for automatic channel search
• (return) – press this button to return
to previous channel, to switch to current
channel press this button once more
Use this button to mirror the picture. Press
this button once more to mirror the picture back.
Using this button you can turn the picture
80 degrees. Press this button once more to
cancel it .
- using this button you can choose picture
format: 4: or 6:9
Installation of batteries into the remote
control
Insert the batteries into the battery compart-
ment of remote control, observing the polarity
according to the marks on the appliance.
When using remote control direct it to the in-
fra red sensor on your TV-set. In case remote
control is not working check the batteries and
replace them if necessary.
Do not expose remote control to excessive tem-
peratures or direct sun light as it could nega-
tively affect its work.
Attention!
Batteries’ leakage could cause damage of re-
mote control. In order to avoid this, follow these
instructions:
- install the batteries properly, observing
the polarity according to the marks on the
appliance;
- take the batteries out if you are not going to
use the appliance for a long time;
- replace the batteries in proper time.
- don’t use old and new batterues together.
- don’t use batteries of different kinds
together.
Connections
Connecting the adapter
Make sure input AC-adapter voltage meets
power supply line voltage. Insert the pin of AC-
adapter into jack DC +2V on your TV-set.
Connecting external antennae
Insert one end of antenna adapter into the jack
for connecting the external antenna to your TV-
set, the other end connect to your antenna.
Connecting audio/video adapter
• Audio/video input (AV/IN)
Insert external video cable into
corresponding jack (yellow color) of your
audio/video adapter. The same way connect
audio cables to corresponding audio/video
adapter’s jacks (left channel insert into
while jack, right channel insert into red jack).
Afterwards connect audio/video adapter to
jack AV/IN  or jack AV/IN 2 on your TV-set.
Screen menu
Press button MENU to view the following menu
items: PICTURE, OPTION, CLOCK, SYSTEM,
PRESET.
Notice: in VIDEO mode menu item SETTINGS is
absent.
Picture
Using buttons CH+/CH- select one of the fol-
lowing parameters: Contrast, Bright, Color, and
Sharp. Use buttons VOL+/ VOL- for adjustment.
5016IM.indd 4 21.02.2008 11:25:59

ENGLISH
5
Option
Using buttons CH+/CH- select one of the fol-
lowing menu items: Language, Calendar, and
Game.
Language
Using buttons VOL+/ VOL- – select one of the
following on-screen menu languages: German,
French, Spain, Italian, or Russian.
Calendar
Using buttons CH+/CH-you can set year, and by
using buttons VOL+/ VOL- you can select cur-
rent month.
Game
Press buttons VOL+/ VOL- to start the game.
Use button VOL- for moving an object to the
left, and use button VOL+ for moving it to the
right, for dropping the object down press but-
ton CH-, press button CH+ to rotate the object.
Press button POWER to exit the game and return
to the previous mode (TV or Video).
Notice: It is recommended to switch to Video
mode before starting the game.
Clock
Using buttons CH+/CH-select one of the follow-
ing modes: Time, on-Time, off-Time, Attention
(appearance of corresponding in preset time),
Bespoke time (switching to preset program in
preset time), Position.
Using button VOL- you can set hour, and using
button VOL+ you can select minutes.
System
Using buttons CH+/CH- select one of the fol-
lowing parameters: Color system, Sound sys-
tem, Blue background, Horizontal, Vertical and
Zoom.
Color system
Using button VOL+ select one of the following
systems: AUTO/PAL/SECAM.
It is recommended to select AUTO.
Sound system
Using button VOL+ select one of the following
systems: BG 5.5M, I 6.0M, DK 6.5M.
Notice: Set sound system depending on your
region. (for Russia - DK)
In case there is no sound or there is noise check
whether the sound system is set properly first.
Blue background
Using buttons VOL+ / VOL- you can switch on/
off blue background in case of signal absence.
Horizontal
Using buttons VOL+ / VOL- you can mirror the
picture. Press button once more to cancel pic-
ture mirror.
Vertical
Using buttons VOL+ / VOL- you can turn picture
up. Press this button once more to cancel it.
Zoom
Using buttons VOL+ / VOL- you can select pic-
ture format: 6:9 or 4:
Preset
Using buttons CH+/CH- select one of the fol-
lowing parameters: Position, Remember, Band,
Swap, Fine, Search and Auto search.
Position
Using buttons VOL+ / VOL- you can select chan-
nel number.
Remember
Using buttons VOL+ / VOL- you can memorize
program number (memory on).
Band
Using buttons VOL+ / VOL- you can elect one
of the following ranges: MW-, MW-2 (meter
waves), DMW (decimeter waves).
Swap
Using buttons VOL+ / VOL- select channel
number for replacement and press button
MENU for confirmation.
Fine
Using buttons VOL+ / VOL- you can fine tune
the channel frequency.
Search
Using buttons VOL+ / VOL- you can start chan-
nels search. After the channel with sufficient
level of signal has been found, search indicator
color is changed.
5016IM.indd 5 21.02.2008 11:25:59