Vive Comfort TP-S-755 User manual

Operation Manual Operation Manual

U.S. Registered Trademark. Patents pending
Copyright 2018 All Rights Reserved.
Table of Contents
Table of Contents
Thermostat Operation
Thermostat Quick Reference
Programming
Features
Warranty Information
Page
2-3
4-7
8-10
1
Una version en español de este
manual se puede descargar en la
pagina web de la compañia.
Equipment damage hazard.
Do not operate the cooling
system if the outdoor
temperature is below 50 ˚F
(10 ˚C) to prevent possible
compressor damage.
Caution
Rev. 1821
11
12
TP-S-755
Vive Comfort
Toll Free : 888-776-1427
Web: www.vivecomfort.com
Hours of Operation: M-F 9AM - 6PM Eastern
P.O. Box 3377
Springeld, MO 65808-3377

Thermostat OperationThermostat Operation
LCD Display
Glow in the dark light button
Fan Button
System Button
Temperature Setpoint Buttons
See page 6 for details about
this display read out.
The glow in the dark light
button will self illuminate
for several hours after
exposure to ambient light.
This button turns on the
display light when pressed.
Select ON, or AUTO. The
ON setting will run the fan
continuously. The AUTO
setting will cycle the fan on
only when the heating or
cooling system is on.
Selects the operation mode
on your HVAC system.
Selecting HEAT turns on
the heat mode. Selecting
COOL turns on the cool
mode. Selecting OFF turns
both heating and cooling
o. (EM HEAT will appear as
an option if operating a heat
pump. EM HEAT setting will
turn on emergency heat)
Press the or
buttons to select the
desired room temperature.
User Program Buttons
See page 8 for further
information.
SYSTEMFAN
Easy Change Battery Door
See page 4 for details.

Thermostat Quick Reference
The low battery indicator is displayed when the AA battery
power is low. If the user fails to replace the battery within 21
days, the screen will only show the low battery indicator but
maintain all functionality. If the user fails to replace the batteries
after an additional 21 days (days 22-42 since rst “low battery”
display) the setpoints will change to 55˚F (Heating) and 85˚F
(Cooling). If the user adjusts the setpoint away from either of
these, it will hold for 4 hours then return to either 55˚F or 85˚F.
After day 63 the batteries must be replaced immediately to
avoid freezing or overheating because the thermostat will shut
the unit o until the batteries are changed.
Important:
Battery Door Information
When the battery icon appears replace your AA
batteries immediately. Failure to do so may result in your
heating & cooling system becoming inoperable.
Freezing or overheating can occur.
Caution:
Thermostat Quick Reference
If your HVAC contractor has congured the thermostat to remind you when
the air lter needs changed, you will see FILT in the display when your air
lter needs to be changed.
Resetting The Filter Change Reminder: When FILT reminder is displayed,
you should change your air lter and reset the reminder by holding dow
the second button down from the top left of the thermostat for 3 seconds.
Filter Change & Other Reminders
Insert 2 AA
Alkaline batteries
(included). High
quality alkaline
batteries are
recommended.
Simple operating instructions are found
on the back of the battery door.

Thermostat Quick Reference Thermostat Quick Reference
Indicates the current room temperature
Time and day of the week
Setpoint: Displays the selected setpoint temperature.
Hold is displayed when the thermostat program is permanently overridden.
System Operation Indicators:
The COOL ON , HEAT ON or icon will display when the COOL, HEAT, or
(fan) is on. The compressor delay feature is active if these are ashing.
1
2
3
7
Low Battery Indicator: Replace batteries when this indicator is shown.
Menu Options: Shows dierent options.
Program Time Periods: This thermostat has 4 programmable time
periods per day.
8
System: Indicates current mode of operation.
Stages: +1 will appear in the display when second stage of heat or
cool is on. +2 will appear for third stage of heat.
8
7
2
1
3
o

Programming Programming
Set Time
Follow the steps below to set the day of the week and current time:
1. Press the MENU button.
2. Press SET TIME.
3. Day of the week will be ashing. Use the or key to
select the current day of the week.
4. Press NEXT.
5. The current hour is ashing. Use the or key to
select the current hour. When using 12-hour time, make sure
the correct a.m. or p.m. choice is selected.
6. Press NEXT.
7. Minutes are now ashing. Use the or key to
select current minutes.
8. Press DONE when completed.
(If using programming)
You will see a Tech Set option after the MENU key is pressed.
This Tech Set key is for installer conguration and should NOT be
changed unless you consult your professional heating and air
conditioning technician.
Important:
Set Program Schedule 5+1+1 or 7 Day
1. Select HEAT or COOL with the system switch. Note: You have
to program heat and cool each seperately.
2. Press the MENU button (If menu does not appear rst press RUN SCHED)
3. Press SET SCHED. Note: Monday-Friday or (Monday if in 7 Day)
is displayed and the WAKE icon is shown. You are now
programming the wake time period for that day.
4. Time is ashing. Use the or key to make your time
selection for that day’s WAKE time period. Note: If you want
the fan to run continuously during this time period, select
ON with the FAN key
5. Press NEXT STEP
6. The setpoint temperature is ashing. Use the or
key to make your setpoint selection for that day’s WAKE time
period.
7. Press NEXT STEP
8. Repeat steps 4 thru 7 for that day’s LEAVE time period,
RETURN time period, and SLEEP time period.
To customize your Program schedule, follow these steps:
Continued on next page...

Programming & Features
Repeat steps 4 through 7 for the Saturday WAKE time period, LEAVE time
period, RETURN time period, and for the Saturday SLEEP time period.
Saturday:
Repeat steps 4 through 7 for the Sunday WAKE time period, LEAVE time
period, RETURN time period, and for the Sunday SLEEP time period.
Sunday:
Set Program Schedule 5+1+1 or 7 Day (continued)
Temporary Hold: The thermostat will display HOLD and RUN SCHED on
the left of your screen when you press the or
key. If you do nothing, the temperature will remain at this setpoint
temporarily for 4 hours. After this, the program setpoint will then replace
your temporary setpoint.
Permanent Hold: With a temporary hold set, if you press the HOLD key at
the left of your screen, you will see HOLD appear below the setpoint tem-
perature in the display. The thermostat will now
permanently stay at this setpoint and can be adjusted using the
or keys.
To Return To Program: Press the RUN SCHED key at the bottom of your
screen to exit temporary and permanent holds.
Temporary & Permanent Hold Feature (If using Programming)
Warranty Information
Warranty Registration
Your new thermostat has a 5 year limited warranty. You must register
your thermostat within 60 days of installation. Without this
registration the warranty period will begin on the date of manufacture.
For warranty issues please contact the HVAC professional that
installed this product. You can register your new thermostat in 2 ways:
Go to the company website, select warranty registration and
ll out a short registration form.
Complete the form below and mail it to the address shown.
Warranty Registration
Complete form and mail to:
Thermostat Warranty Registration
Online
Mail
If using 7-Day Programming:
Use these same steps for every individual day.
Vive Comfort
P.O. Box 3377
Springeld, MO 65808-3377
Name:
Address:
City:
State:
Zip:
Thermostat Model:
Date Installed:

Cut Out For
Warranty Registration
www.vivecomfort.com