Crestron Cresnet CHV-TSTAT-FCU Dimensional drawing

DO GUIDE
DO Connect the Device
Make the necessary connections as called out in the illustrations that follow. A miniature at-
head screwdriver (not supplied) is required to attach the control wires from the HVAC system.
Apply power after all connections have been made.
If the system being connected does not match the system described below, contact Crestron
Technical Support for assistance.
Cresnet Connections
CHV-TSTAT-FCU
Cresnet®Thermostat
DO Install the Device
NOTE: Installers should have a strong working knowledge of HVAC systems.
The location of the thermostat can affect its performance and efciency. Install the thermostat
away from direct sunlight, drafts, doorways, skylights, and windows. Also, make sure that the
thermostat is conveniently located for control access and setup.
Thermostats should be mounted 60 inches (~1.6 meters) above the nished oor; this is an
HVAC industry standard. Do not mount on an exterior wall.
The following tools and hardware are required for installation:
• Standard 1-gang electrical box, mounted horizontally (not supplied)
• Phillips screwdriver (not supplied)
Install the thermostat in the 1-gang electrical box.
1. Turn the HVAC system power off.
2. Separate the thermostat front plate from the rear plate. It may be necessary to exert force
when removing the front plate.
3. Feed the HVAC wiring from the electrical box through the hole in the center of the rear
plate.
4. Make HVAC connections. Refer to the “DO Connect the Device” section for details.
CAUTION: Excess wire pinched between the CHV-TSAT-FCU and the electrical box
can cause a short circuit. Make sure that excess wire is inside the electrical box and not
between the box and the device.
NOTE: To ensure accurate temperature readings, avoid drafts in the back of the unit by
plugging the wire hole with insulation.
5. Attach the CHV-TSTAT-FCU rear plate to the electrical box using the included screws.
CAUTION: Do not press on the LCD display during mounting, as this may cause the screen
to crack.
6. Attach the front plate.
7. Carefully remove the warning label from the LCD display.
8. Turn HVAC system power on.
DO Check the Box
QTY PRODUCT PART NUM.
2 Screw, 6-32 x 1", Pan Head, Phillips 2007251
NETWORK
24V Y Z G
To control
system.
24 Vdc is
required.

DO GUIDE DOC. 7914A (2047480) 11.16
Specications subject to change without notice.
HVAC Connections DO Congure the Device
Press and hole the MODE and VIEW buttons at the same time to enter Setup mode. For detailed
setup information, refer to the CHV-T STAT-FCU Supplemental Guide (Doc. 7963)
at www.crestron.com/manuals.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specic patents that cover Crestron products are listed at http://www.crestron.com/legal/patents. The product warranty can be found at www.crestron.com/warranty.
Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, and Cresnet are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered
trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc.
TOP
NETWORK
24V Y Z G
RSR
RSR
RS1
RS2
24(R)
-
24(C)
HUM
RHU
R R
W
Y
G-L
G-M
G-H
O
B
24 Vac from
transformer Y - Cool
valve
W - Heat
valve
R - Reference
G-H - Fan high
G-M - Fan medium
G-L - Fan low
1
2
3
4
P4
P4 must be
connected
between pins
2 and 3 on the
rear of the unit.