VividLeds Iris SP VVDSPJ1600 User manual

!WARNING
PLEASE READ ALL INSTRUCTIONS BEFORE ATTEMPTING INSTALLATION
-To prevent personal injury or product damage only licensed electricians should install.
- To avoid electric shock or component damage disconnect power before attempting installation or servicing.
- This product must be installed in accordance with the national electric code (NEC) and all applicable federal, state and local electric codes and safety standards.
- Disconnect product and allow cooling prior to servicing.
- Any alteration or modification of this product is expressly forbidden as it may cause serious personal injury, death, property damage and/or product malfunction.
- To prevent product malfunction and/or electrical shock this product must be properly grounded.
- This luminaire is designed to operate in ambient temperatures ranging from -40°C to 55°C and to be horizontally mounted with the LEDs facing down.
- This product must be installed in accordance with the applicable installation code by a Person familiar with the construction and operation of the product and the
hazards involved.
- MIN 90°C SUPPLY CONDUCTORS.
- CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
- CAUTION - RISK OF FIRE.
- This product is not available for several special environments, such as places with corrosive gas liquids or high pressure water vapor.
1. All electrical work must conform to the National Electric Code (NEC) and all applicable local codes and ordinances.
2. Sportsbeams lighting should only be installed by qualified personnel. Please ensure that you have verified the safety of any existing power distribution systems
before beginning installation. Failure to follow Operating Instructions may lead to death, Severe Injury, or Property Damage.
Turn off power before performing any electrical or control work. FAILURE TO FOLLOW THIS WARNING MAY LEAD TO DEATH, SEVERE INJURY,
OR PROPERTY DAMAGE.
DO NOT make or alter any open holes in the luminaire. Do not modifty the luminaire.
Follow all applicable safety procedures and use Personal Protective Equipment such as hardhats, safety glasses, reflective vests, electrical safety gloves,
fall protection equipment and safety toe boots during the insalltion, operation, and maintenance of the luminaire. FAILURE TO FOLLOW THIS WARNING MAY
LEAD TO DEATH, SEVERE INJURY, OR PROPERTY DAMAGE.
NEVER Risk eye injury! Eye protection is required at all times during the installation, operation, and maintenance of the luminaire. The high intensity light
produced by the luminaire can cause severe damage to the eye if viewed directly at close range. Avoid being in front of a luminaire that is on or wear suitable light
blocking protective eyewear such as welding goggles. Store luminaires in a clean, dry place, protected from dirt, water, and sunlight.
Installation Guide
1. Drill appropriate knockout according to the size of the mounting bracket.
2. Once fxture is positioned, secure the fxture with screws tightly.
3. Make all necessary wiring connections, observing proper voltage and polarity. Ensure that wires are seated
properly and not being pinched.
4. Once connections are completely made, carefully push all wires down into the housing and secure it tightly.
5. Using aiming sight to orient desired mounting angle.
6. Installation and service of luminaires should be performed by a qualifed licensed electrician.
522mm/20.55in
383mm/15.08in
Ø360mm/14.17in
400-500W dimensions
224mm/8.81in
164mm/6.45in
17mm/0.66in
Ø17mm/0.66in
637mm/25.07in
462.2mm/6.38in
䌙㻠㻢㻝㻚㻠㼙㼙㻛㻝㻤㻚㻝㻢㼕㼚
䌙㻞㻞㼙㼙㻛㻜㻚㻤㻢㼕㼚
200mm/7.87in
280mm/11.02in
22mm/0.86in
600-720W dimensions
1
Take the Screw ,fit visor ( M4 6pcs
screw Torque Values 2.5 N.m ) .

0
110
100 90
80
70
60
50
40
30
20
10
0
110
100
90
80
70
60
50
40
30
20
10
0
110
100
90
80
70
60
50
40
30
20 10
0
110
100 90
80
70
60
50
40
30
20
10
PE
L
N
DIM+
DIM-
0
110
100 90
80
70
60
50
40
30
20
10
0
110
100 90
80
70
60
50
40
30
20
10
AC Cable:
UL:SJTW/3C/18AWG/300V
CE:H05RN-F/3C*1.0m2/300-500V
DIM Cable:
UL:SJTW/2C/18AWG/300V
CE:H05RN-F/2C*1.0m2/300-500V
10
5
10
5
10
5
1.Take the Screw ,fit visor ( M6 screw Torque Values 4.0 N.m ) .
2.Take the Screw ,fit visor ( M12 screw Torque Values 38.5 N.m ) .
1.Take the Screw ,fit visor ( M6 screw Torque Values 4.0 N.m ) .
2.Take the Screw ,fit visor ( M12 screw Torque Values 38.5 N.m ) .
1.Take the Screw ,fit visor ( M6 screw Torque Values 4.0 N.m ) .
2.Take the Screw ,fit visor ( M12 screw Torque Values 38.5 N.m ) .
2
3
4