Feit Electric TAPE192/RGBW/AG User manual

MODEL: TAPE192/RGBW/AG
FEIT ELECTRIC COMPANY • Pico Rivera, CA, USA • www.feit.com
LIMITED WARRANTY. This product is warrantied to be free from defects in
workmanship and materials for up to 1 year from date of purchase. If the
product fails within the warranty period, please contact Feit Electric at
feit.com/help for help. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS
HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the
exclusion of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state or province
to province.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ELECTRICAL RATINGS:
INPUT: 120-240VAC,
50/60HZ, 0.45A MAX
OUTPUT: 24VDC,
1A, 24W MAX
RANGE: 100 FEET
- WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN
- Swallowing may lead to serious injury or deathin as little as 2 hours,
due to chemical burns and potential perforation of the esophagus.
- If you suspect your child has swallowed or inserted a button battery,
immediately seek urgent medical assistance.
- Examine devices and make sure the battery compartment is correctly
secured, e.g. that the screw or other mechanical fastener is tightened.
Do not use if compartment is not secure.
- Dispose of used button battery immediately and safely. Flat battery
can still be dangerous.
RF Remote Control
ON: Turns On the Strip Light
OFF: Turns Off the Strip Light
UP ARROW: Increases brightness of white light
DOWN ARROW: Decreases brightness of white light
CHANGE COLORS: Changes solid colors
STROBE COLORS: Turns strip on and off as it rotates through colors
FLASH COLORS: Rapidly rotates through colors
FADE COLORS: Smoothly transitions through colors
Controller Module Button
- Single click - On/Off
- Press and hold when lights
are on - adjusts dimming.
- Reset unit and enter smart pairing mode to
connect to Wi-Fi.
When using electrical products, basic
precautions should always be practiced
including the following:
IMPORTANT SAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Only supports 2.4GHz
Wi-Fi networks
Quick Install Guide
Color Changing - 16ft.
Indoor / Outdoor
Raintight
If you are using the remote control with this set, you do not need to
do anything else. The controller and remote come pre-paired together.
Controlling Multiple Strip Lights
By Remote: The remote in this set can control a strip light from an
additional Feit Electric set (sold separately) if the additional controller
module has a model number ending in SC. The model number is located on
the back of the controller module.
If the controller model ends in SC, connect power to the strip light you want
to pair. As soon as the strip light is plugged in, press the remote control On
button then Off button. Repeat this every second for up to 30 seconds.
When the strip light is paired to the remote, the strip will turn On and Off with
your button presses. You will then be able to control the strip light with the
paired remote.
Link Together: Connect one strip light into the end of the other strip light.
Maximum total length: 32 feet.
Smart Control: Control multiple sets together by connecting to Wi-Fi
through the Feit Electric app.
This product contains a button battery. If swallowed, it could cause severe
injury or death in just 2 hours. Seek medical attention immediately.
Supplier’s Declaration of Conformity:
47 CFR § 2.1077 Compliance Information
Responsible Party:
Feit Electric Company
4901 Gregg Road;
Pico Rivera, CA 90660, USA
562-463-2852
Unique Identifier:
TAPE192/RGBW/AG
BATTERY WARNING:
Risk of fire, explosion, and burns. Do not disassemble, crush, heat above
100º C / 212º F or incinerate. REPLACE ONLY WITH one CR2032 battery.
DISPOSE OF USED BATTERY PROMPTLY. KEEP AWAY FROM CHILDREN.
DO NOT DISASSEMBLE AND DO NOT DISPOSE OF IN FIRE.
When replacing battery, ensure the new battery is installed correctly with
regard to polarity (+ and -) as shown on remote.
WARNING:
WARNING:
WARNING:
Risk of Electric Shock. When used outdoors, install only to a covered
Class A GFCI protected receptacle that is weatherproof with the power
unit connected to the receptacle. If one is not provided, contact a
qualified electrician for proper installation. Ensure that the power unit
and cord do not interfere with completely closing the receptacle cover.
Risk of Electric Shock. Mount the unit at a height greater than 1 foot
from the ground surface.
This manual contains important safety and operating instructions
to power the unit.
CAUTION:
Dispose of used battery promptly according to local recycling or waste
regulations. Clean battery contacts and also device contacts prior to
installing battery. Ensure the battery is installed correctly with regard to
polarity (+ and –). Remove battery from remote when not being used for
an extended period of time. Remove used battery promptly. The LEDs in
this strip light are not replaceable.
SCAN ME
for a “HOW TO” video
Smart LED
Strip Light
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
2. Read and follow all instructions on the product or provided
with the product.
3. Unplug from outlet before shortening, cutting or installing
this product
4. Do not use an extension cord to supply power to the strip.
5. Do not use within 10 feet of a pool.
6. Do not use in a bathroom.
7. This product is NOT a toy.
8. To avoid damage, use only with the power supply provided.
9. Do not open the product. Use only as intended.
10. Do not roll up the product when using. Spread out to full length
before connecting power supply.
11. Do not operate if any component is damaged.
Controller
Module
Remote
Control
ON OFF
FEIT ELECTRIC
WHITE WHITE
CHANGE
COLORS
STROBE
COLORS
FLASH
COLORS
FADE
COLORS

TROUBLESHOOTING TIPS CONNECTING TO WI-FI
If you are having difficulty connecting:
• Make sure the Wi-Fi network is a 2.4 GHz network.
Smart Strip Light will not connect to a 5 GHz network.
• Test your Wi-Fi network with other devices such as your
phone to make sure it is operating properly.
• The Wi-Fi connection may not have good coverage
during set up. Try moving the Smart Strip Light closer
to your Wi-Fi router.
For more information, check the App User Guide and visit
www.feit.com/help
Download the Feit Electric app
on your smart device
Prepare the Strip Light
Connect the Controller Module
Feit Electric app
Mount the Strip Light
Getting Started:
Peel adhesive tape from back of Strip Light to position
and align strip light on mounting surface.
Screw in mounting clips (required for all long term
installations). Save two clips to use for installing the
Controller Module (Step 4).
Need Help?
FOR DETAILED INSTRUCTIONS ON SMART FEATURES SEE THE APP USER GUIDE.
WARNING:
These products may represent a possible shock or fire hazard if improperly
installed or attached in any way. Products should be installed in accordance
with this install guide, current electrical codes and/or the current National
Electric Code (NEC).
Once cut, the portion of the strip light that will not connect to the controller
can be disposed of in accordance with local recycling or waste regulations.
- Measure the desired length before installation.
- Clean the mounting area thoroughly (surface
must be free of dust, dirt or grease).
- Avoid bending the strip light which may
damage the LEDs.
- Avoid removing and relaying the Strip Light
multiple times as the adhesive may wear off.
Unroll strip light and place near mounting location.
Ensure power supply and controller can reach to the
start of the strip light. Do not connect to power yet.
(Optional) Connect to Google Assistant
or Alexa using the in App guide
Choose Alexa
or Google Assistant
Tap ••• menu icon
6
mounting clip
mounting
clip
To activate smart features proceed to steps 5 & 6.
When in Smart Wi-Fi pairing mode, the strip light will
blink. Note: The unit will stop blinking after 3 minutes
or when controlled with the RF remote.
You are now ready to use the Strip Light via RF Remote
Controller. See “RF Remote Control” section for details.
For 24/7 customer support,
visit feit.com/help
90˚ Max
Do not bend at LED
90˚ Max
Turn on Bluetooth and open the
Feit Electric app to complete the set up.
5
Be sure to connect to a 2.4 GHz
Wi-Fi network that covers your
installation location.
Tap Add Device or the + sign. The device name(s)
will pop up on the Feit app. Tap on Go to add,
then select the device to add.
You will be prompted to enter
your Wi-Fi network name and
password.
Only one device may be added at
a time using Bluetooth set up.
Repeat Step 5 to add additional
devices. Alternative set up options
and help instructions are available
in the Feit Electric app.
Connect the Strip Light to the controller module then
connect the plug as shown in the image below.
Connect power supply to wall outlet.
When using outdoors, plug the unit
into an outdoor rated GFCI receptacle
with appropriate outdoor cover.
•••
Use provided double-sided tape to adhere
the back of Controller Module to mounting
surface. Use mounting clips on both sides
as shown above.
This strip light uses permanent tape and may cause surface damage
if removed. Not recommended for mounting on brick or concrete.
Feit Electric is not responsible for damage to mounted surfaces.
Ensure the power supply is not plugged
in at the wall outlet when mounting
or cutting.
Cut to length ONLY on the line or solder
pads NEXT to the scissor markings on
strip light, where the copper or silver
metal is visible. Cutting at any other
area will permanently damage the strip.
Optional - Add another Feit Electric Smart LED Strip Light
(sold separately) to extend up to 32 feet.
SILVER
CONNECTION
COPPER
CONNECTION
CUT HERE CUT HERE
Apply tape to back
of male connector
If you are connecting two strip lights, use the included foam tape
to secure male connector to mounting surface.
FOAM TAPE