Vivo DESK-V000K-M2/G/W User manual

Desk Riser with Dual Monitor Mount
Instruction Manual
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/desk-v000k-m2
SKUS: DESK-V000K-M2/G/W
DESK-V000KN-M2

2 3
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
PACKAGE CONTENTS
33lbs
(15kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
STEP 2
Apply Pads (D) to the underside of Keyboard Tray (B). Install Stopper (C) on Keyboard Tray (B) using
ST4.2x12mm Screws (S-A) in the pre-drilled holes and a Phillips screwdriver.
Install Rubber Feet (E) to the bottom of Desk (A). Then cut the large shipping tie.
NOTE: DO NOT squeeze the handle on Desk (A) while cutting the shipping tie.
WARNING!
A (x1)
Desk
G (x1)
Arm
H (x1)
Pole
M (x1)
Grommet Plate
N (x1)
Hand Bolt
O (x1)
Support Plate
P (x5)
Rubber Pads
Q (x2)
Knob
I (x2)
VESA Plate
J (x1)
Pole cable Clip
K (x4)
Arm Cable Clip
L(x1)
Pole Cap
S-A (x2)
ST4.2x12mm Screw
M-D (x8)
M5x16mm Screw
M-E (x8)
M5 Washer
M-F (x8)
Spacer
T-A (x1)
6mm Allen Wrench
S-B (x4)
M5x10mm Screw
S-C (x2)
M3x8mm Screw
M-A (x8)
M4x12mm Screw
M-B (x8)
M4x16mm Screw
M-C (x8)
M5x12mm Screw
B(x1)
Keyboard Tray
C (x1)
Stopper
D (x3)
Pad
E (x4)
Rubber Feet
F (x2)
Cable Clips
TOOLS NEEDED
Scissors
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Phillips
Screwdriver DESKTOP
4.4lbs
(2kg)
17.6lbs
(8kg)
KEYBOARD TRAY PER SCREEN
D
B
S-A
C
A
E
Raise desktop
slowly to keep
items stable.
Keep monitor and
laptop base fully on
the desktop.
Leave enough slack
in cable to allow for
full range of vertical
motion (15” / 38 cm).
Follow the cable
routing instructions to
avoid the potential to
pinch cables.
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.

4 5
Raise Desk (A) by liing the handle on the right side of the frame.
Place Keyboard Tray (B) on the metal brackets on Desk (A). Secure Keyboard Tray (B) to brackets using
M5x10mm Screws (S-B) and tighten with a Phillips screwdriver.
S-B
A
A
B
STEP 5
Apply Cable Clips (F) to underside of Desk (A).
STEP 4
A
F
STEP 6
Insert Pole Cap (L) into Pole (H).
L
H
Remove adhesive backing from Rubber Pads (P) and place them on the underside of over Grommet
Plate (M). Remove plug from Desk (A).
A
P
M
STEP 7STEP 3
STEP 8
A
M
N
O
H
Position Pole (H) with Grommet Plate (M) over the grommet hole of Desk (A), and install to desktop
using Hand Bolt (N) with Support Plate (O). Tighten and secure.
J
H
K
T-A
G
STEP 9
Slide Pole Cable Clip (J) and Arm (G) onto Pole (H) and secure at the desired height using 6mm Allen
Wrench (T-A). Attach Arm Cable Clips (K) to Arm (G).

6 7
STEP 10
I
M-A
M-C
M-E
STEP 12
Flat Back Monitor
Install VESA Plates (I) to monitors using Screws (M-A or M-C) and M5 Washers (M-E).
Curved / Recessed Back Monitor
Install VESA Plate (I) to monitors using Screws (M-B or M-D), M5 Washers (M-E) and Spacers (M-F).
I
M-B
M-D
M-E
M-F
STEP 11
If needed, adjust tilt joint support using 6mm Allen Wrench (T-A).
Slide the VESA Plates (I) with monitors onto the Arms (G). Secure using the Knobs (Q) with M3x8mm
Screws (S-C).
Q
S-C
I
K
STEP 13
T-A
Q
T-A
J
T-A
STEP 14
CAUTION: To prevent tipping, please be careful not to extend the arms too far forward or backward.
Adjust monitor position and rotation as desired. Adjust monitor alignment by turning Knob (Q) with
6mm Allen Wrench (T-A). Store Allen Wrench (T-A) in the Pole Clip (J) for future adjustments.
G
Route cables through Arm Cable Clips (K) and Pole Cable Clip (J).
J
K

LAST UPDATED: 03/21/2023
REV3
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303