Vivo STAND-V001HG User manual

Single Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001hg
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V001HG

2 3
ASSEMBLY STEPS
STEP 1
PACKAGE CONTENTS
TOOLS NEEDED
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
a (x1)
Pole
b(x1)
Glass Base
c(x1)
Monitor Arm
j (x1)
Support Plate
l (x1)
Spring
Washer
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
d(x1)
VESA Plate
e(x1)
Decorative Cover
f (x3)
M6x10
g(x3)
Connecting Bolt
h (x3)
M8 Washer
i (x1)
M10 Bolt
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
m (x4)
Rubber Feet
k (x1)
M10 Washer
OPTION A: Weighted Base Installation
1. Attach Rubber Feet (m) to the underside of the Glass Base (b). See Figure 1.
2. Attach So Pad (n) to the Pole (a). See Figure 2.
3. Use a screwdriver to poke holes for screws through the pad. Install Pole to Glass Base using M6x10
Bolts (f), Connecting Bolts (g) and M8 Washers (h), and tighten with medium Allen Key (u) and
screwdriver. Slide Decorative Cover (e) over the Pole. See Figure 3.
4. (Optional) Drill a 10mm diameter hole in your desk and secure using the Support Plate (j), M10
Washer (k), Spring Washer (l) and M10 Bolt (i). Fasten the M10 Bolt with provided Wrench (t). See
Figure 4.
n (x1)
So Pad
o (x1)
Wire Clip
q (x4)
M4x12
r (x4)
M4x30
p (x1)
M4x6
s (x4)
M4 Spacer
t (x1)
Wrench
u (x1)
Allen Key
Figure 1 Figure 2
m
n
b
Figure 3
b
g
h
f
e
a
Figure 4
i
k
j
l
Drill

4 5
STEP 1 (Continued)
OPTION B: Grommet Base Installation
1. If the existing grommet hole comes with a plastic protector,
rst remove it to ensure a at mounting surface. Attach So
Pad (n) to Pole (a). See Figure 5.
2. Position Pole on the mounting surface and secure using the
Support Plate (j) , M10 Washer (k), Spring Washer (l) and M10
Bolt (i). Tighten using the Wrench (t), and slide Decorative
Cover (e) over the top of the Pole. See Figure 6.
STEP 2
Install Monitor Arm (c) to the Pole (a). Fasten the
bolt with supplied Allen Key (u). Attach the Wire
Clip (o) to the Pole (a) with the large Allen Key (u).
OPTION C: Self-Drilled Grommet Base Installation
1. Determine mounting location on desktop and mark the
center drilling location. Drill a 3/8” (10mm) diameter hole
through surface at the marked location. Attach So Pad (n) to
Pole (a) See Figure 7.
2. Position Pole on the mounting surface and secure using the
Support Plate (j), M10 Washer (k), Spring Washer (l) and M10
Bolt (i) (Figure 7). Tighten using the Wrench (t), and slide
Decorative Cover (e) over the top of the Pole. See Figure 8.
STEP 3
OPTION A: Flat Back Monitor
For monitor with at back, attach VESA plate (d) to monitor using thumb screws (q).
Figure 6
Figure 5
n
i
l
k
j
e
Figure 8
Figure 7
n
i
l
k
j
e
c
o
u
q

6 7
STEP 3 (Continued) STEP 5
Tighten the grub screw in the Monitor Arm (c) using the small Allen Key (u) to x the tilting angle.
Manage the cables and store tools using the Wire Clip (o).
OPTION B: Curved Back Monitor
For monitor with curved back, attach VESA plate (d) to monitor using M4x30 bolts (r) with spacers (s).
STEP 4
Slide the monitor onto the head of Monitor Arm (c) as shown in the diagram. Secure the VESA Plate (d)
using M4x6 Bolt (p). Make sure the bolt is installed before you rotate the monitor.
s
r
p
grub
screw

Last Updated: 11/27/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654