Vivo MOUNT-PC07G User manual

Deskside and Wall Gaming PC Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-pc07g
SKU: MOUNT-PC07G
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause damage or serious injury. Do not
use this product for any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
ASSEMBLY STEPS
STEP 1
Remove adhesive backing from Thin Pads (G) and place them onto Inner and Outer Shelves (A,B).
TOOLS NEEDED
Phillips
Screwdriver
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
66 lbs
(30 kg)
A (x1)
Inner Shelf
S-A (x3)
Wing Nut
S-B (x4)
M4x6mm Screw
W-D (x2)
ST4.2x35mm
Screw
W-E (x2)
M6x60mm
Molly Bolt
T-A (x1)
4mm Allen Wrench
S-C (x4)
M6x6mm Screw
W-A (x6)
ST5.5x38mm
Screw
W-B (x6)
Concrete Anchor
W-C (x2)
Self-Tapping
Drywall Anchor
B (x1)
Outer Shelf
C (x1)
Le Support
Bracket
D (x1)
Right Support
Bracket
Stud Finder Pencil Drill Level
E (x2)
Clamp
F (x1)
Locking
Bracket
G (x6)
Thin Pad
H (x6)
Thick Pad
STEP 2
Attach Le and Right Support Brackets (C,D) to Inner Shelf (A) using M4x6mm Screws (S-B) and a
Phillips screwdriver.
G
A
B
C
D
A
S-B
22 lbs
(10 kg)
Clamp/Wood/
Concrete/Brick
Drywall

4 5
STEP 3 STEP 5 (Option B)
STEP 4
STEP 5 (Option A)
Attach Outer Shelf (B) to Inner Shelf (A) using Wing Nuts (S-A).
Remove adhesive backing from Thick Pads (H) and apply them to Inner and Outer Shelves (A,B).
Clamp Installation
Attach Clamps (E) to Le and Right Support Brackets (C,D) using M6x6mm Screws (S-C) and 4mm
Allen Wrench (T-A), so that the clamps are oset towards the center of the mount. Attach the mount
assembly to a desktop and adjust the width using Wing Nuts (S-A) and place PC into the mount.
Concrete/Brick Wall Installation
Hold the assembled mount to the wall and mark hole locations for drilling. Use of a level is highly
recommended. Drill 1.8” (45mm) deep pilot holes using a 5/16” (8mm) drill bit. Press Concrete Anchors
(W-B) into the wall and attach the mount using ST5.5x38mm Screws (W-A) and a Phillips screwdriver.
Place PC in mount and hold Locking Bracket (F) to the wall directly above the PC. Mark hole locations
and remove the PC from the mount. Drill 1.6” (40mm) deep pilot holes using a 5/16” (8mm) drill
bit. Place the PC back into the mount and install Locking Bracket (F) using Concrete Anchors (W-B),
ST5.5x38mm Screws (W-A), and a Phillips screwdriver.
B
A
S-A
H
AB
E
C
D
T-A S-C
S-A
W-BW-B
W-AW-A
F

6 7
STEP 5 (Option C) STEP 5 (Option D)
Wood Wall Installation
Hold the assembled mount to the wall and mark hole locations for drilling. Use of a level is highly
recommended. Drill 1.6” (40mm) deep pilot holes using a 5/32” (4mm) drill bit. Attach the mount using
ST5.5x38mm Screws (W-A) and a Phillips screwdriver. Place PC in mount and hold Locking Bracket (F) to
the wall directly above the PC. Mark hole locations and remove the PC from the mount. Drill 1.6” (40mm)
deep pilot holes using a 5/32” (4mm) drill bit. Place the PC back into the mount and install Locking
Bracket (F) using ST5.5x38mm Screws (W-A) and a Phillips screwdriver.
Drywall Installation
WARNING: THIS INSTALLATION METHOD IS ONLY RATED FOR A 22LBS (10KG) MAX LOAD.
Hold the assembled mount to the wall and mark hole locations for drilling. Only mark the top hole
on each support bracket. Use of a level is highly recommended. Drill completely through the drywall
using a 25/64” (10mm) drill bit. Tap M6x60mm Molly Bolts (W-E) into the drilled holes until flush with
the wall. Use a Phillips screwdriver to tighten the screw to expand the anchor in the wall. Tighten until
the anchor feels snug and the bolt resists hand-tightening. Remove the bolt and washer from the
installed anchor. Install the assembled mount to the anchors using the previously removed bolts and
washers. Place PC in the mount and hold Locking Bracket (F) to the wall directly above the PC. Mark
hole locations and remove the PC from the mount. Screw Self-Tapping Drywall Anchors (W-C) into the
wall at marked locations using a Phillips Screwdriver until the head of the anchor is flush with the wall.
Place the PC back into the mount and install Locking Bracket (F) using ST4.2x35mm Screws (W-D) and
a Phillips screwdriver.
F
W-A
W-E
F
W-C W-D

LAST UPDATED: 03/10/2023
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303