Vivo STAND-LIVE2L User manual

Black All-In-One Livestream Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-live2l
SKU: STAND-LIVE2L
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Top Pole
B(x1)
Bottom Pole
C(x1)
Mic Boom
J (x2)
Camera Mount
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Pole Connector
E(x1)
Clamp
F (x2)
VESA Plate
G(x1)
Dual Arm
H (x2)
Single Arm
I (x1)
Mic Arm
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x2)
Mic So Pad
L (x1)
Mic Clamp
M (x1)
Grommet So
Pad
N(x1)
Grommet Plate
O (x2)
Camera Adjustment
Handle
P (x2)
Pole Cable Clip
Q (x8)
Arm Cable
Clip
R(x1)
Mic Mount
S(x1)
Pole Cap
T (x1)
Laptop Tray
U (x2)
Laptop Mount
V (x2)
Laptop Arm Clip
S-A (x1)
Mic Thumbscrew
S-B (x4)
M4x8 Screw
S-C (x2)
VESA Thumbscrew
S-D (x3)
M6x16 Screw
S-E (x1)
M5x16 Screw
S-J (x2)
VESA Cap
S-F (x6)
M6x10 Screw
S-G (x4)
M4x8 Screw
S-H (x2)
1/4” to 3/8” Adapter
S-I (x1)
D12 Washer
M-D (x8)
M5x16 Screw
S-K (x2)
M3x8 Screw
M-A (x8)
M4x12 Srew
M-B (x8)
M4x16 Screw
M-C (x8)
M5x12 Screw
M-E (x8)
D5 Washer
M-F (x8)
5mm Spacer
T-A (x1)
4mm Allen Wrench
T-B (x1)
6mm Allen Wrench

3
ASSEMBLY STEPS
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
Using 4mm Allen Wrench (T-A), loosen screws on clamp (E) and separate into two parts, Clamp
Brace (E1) and Clamp (E2).
TOOLS NEEDED
15.4lbs
(7kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 1
2.2lbs
(1kg)
MICROPHONE CAMERA & LIGHT
19.8lbs
(9kg)
MONITOR
(per screen)
9.9lbs
(4.5kg)
LAPTOP
STEP 2
Option A: Clamp Installation
Mount Clamp (E1) to Bottom Pole (B) using
M6x16 Screws (S-D) and 4mm Allen Wrench
(T-A). Remove adhesive backing from Grommet
So Pad (M) and stick it to Clamp Brace (E1).
OPTION B: Grommet Installation
If not using an existing through-hole, using a
10mm (⅜”) drill bit, drill through the desktop
at least 2” away from the edge. Disassemble
Clamp (E2) using a Philips screwdriver. Set
aside all parts except for Clamp Bolt (E3)
Support Plate (E4).
T-A
E
E1
E2
E1
T-A
S-D
B
M
E2 E3
E4

4
STEP 2 (Continued)
OPTION A: Clamp Installation
For thinner desktops, re-attach Clamp (E2) to
Clamp Brace (E1) and tighten the bolts using
4mm Allen Wrench (T-A).
OPTION B: Grommet Installation
Cut Grommet So Pad (M) along perforated
lines, then remove adhesive backing and stick to
Grommet Plate (N). Attach Pole (B) to Grommet
Plate (N) using M5x16 Screw (S-E) and a phillips
screwdriver. Mount assembly to the desktop
using the Support Plate (E4) and Clamp Bolt
(E3) as shown below.
M
N
B
S-E
E4
E3
E2
E1
For thicker desktops, disassemble Clamp (E2)
using a Phillips screwdriver. Flip Clamp (E2) over
and reassemble. Then re-attach Clamp (E2) to
Clamp Brace (E1) and tighten bolts using the 4mm
Allen Wrench (T-A).
T-A
E2
E1
T-A

5
Slide Dual Arm (G) and Mic Arm (I) onto Bottom Pole (B) and tighten using 6mm Allen Wrench (T-B).
Use Pole Connector (D) to secure Top Pole (A) to Bottom Pole (B) with M6x10 Screw (S-F) and 4mm
Allen Wrench (T-A). Slide Single Arms (H) onto Top Pole (A) and tighten using 6mm Allen Wrench
(T-B). Insert Pole Cap (S) into Top Pole (A) and attach Pole Cable Clips (P) to Bottom Pole (B) and Top
Pole (A).
NOTE: This is the recommended assembly, but this and the following steps are optional and depend
on user preference.
STEP 3
G
I
B
T-B
T-B
D
A
S-F
T-A
H
S
P

6
STEP 4 (MONITOR ATTACHMENT)
Attach VESA Plate (F) to the back of the monitor using Screws (M-A through M-D) and Washers (M-E).
If needed, use Spacers (M-F). Slide VESA Plate (F) onto Dual Arm (G) and secure using VESA Cap (S-J),
M3x8 Screws (S-K), and a phillips screwdriver.
G
S-J
S-K

7
STEP 4 (CAMERA MOUNT ATTACHMENT)
Attach Camera Adjustment Handles (O) to Camera Mounts (J) using M4x8 Screws (S-G) and a phillips
screwdriver. Remove adhesive backing from Mic So Pads (K) and stick to Camera Mounts (J). For
some cameras, 1/4” to 3/8” Adapters (S-H) maybe required. Slide Camera Mounts (J) onto Single
Arms (H) and secure using VESA Thumbscrew (S-C).
J
O
S-G
K
S-H
H
S-C
1/4” to 3/8” Adapter (S-H) included
for ball heads, cameras and lighting

8
STEP 4 (MIC BOOM ATTACHMENT)
Option A: For arm mounting, slide Mic Boom (C) onto Mic Arm (I) with D12 Washer (S-I). Insert Mic
Thumb Screw (S-A) into Mic Arm (I) to secure into place. Thread Mic Mount (R) onto Mic Boom (C).
C
I
R
S-A
S-I
S-A
L
Option B: For desktop mounting, attach Mic Clamp (L) to to desktop. Insert Mic Boom (C) into Mic
Clamp (L) and secure using Mic thumbscrew (S-A). Thread Mic Mount (R) onto Mic Boom (C).
C
R

9
STEP 4 (LAPTOP TRAY ATTACHMENT)
Place Laptop Mounts (U) underneath each side of Laptop Tray (T), aligning square holes in Laptop
Mounts (U) with the edge and long slot on each side of Laptop Tray (T). Insert Laptop Arm Clips (V)
through top to secure Laptop Mounts (U). Mount VESA Plate (F) to Laptop Tray (T) using M4x8 Screws
(S-B) and a phillips screwdriver. Slide VESA Plate (F) onto Dual Arm (G) and secure using VESA Cap
(S-J), M3x8 Screws (S-K), and a phillips screwdriver. Release locks on underside of Laptop Mounts
(U). Extend Laptop Mounts (U), place laptop Laptop Tray (T), then adjust Laptop Mounts (U) to width
of laptop. Engage locks to secure laptop.
U
T
V
S-B
F
G
S-K
S-J

10
STEP 5
Adjust tilt joint using 6mm Allen Wrench (T-B). Adjust monitor height by using 6mm Allen Wrench in
VESA Caps (S-J).
T-B
T-B
T-B
S-J

11
STEP 6
Insert Arm Cable Clips (Q) under Dual Arm (G) and Single Arms (H). Route cables through Arm Cable
Clips (Q) and Pole Cable Clips (P). Store Allen Wrenches (T-A and T-B) in Cable Clips (P). Adjust as
desired.
P
T-A
T-B
Q
P
G
H

LAST UPDATED: 09/02/2021
REV1.1
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303