Vivo STAND-V002FG User manual

Dual Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002fg
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V002FG

2 3
ASSEMBLY STEPS
STEP 1
PACKAGE CONTENTS
TOOLS NEEDED
Phillips
Screwdriver
a (x1)
Pole
b(x1)
Weighted Base
c(x1)
Swivel Arm
j (x1)
Spring Washer
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
d(x2)
VESA Plate
e(x3)
M6x10
f (x2)
Nut
g (x1)
M10 Bolt
h (x1)
Support Plate
i (x1)
M10 Washer
k (x3)
Connecting
Bolt
o (x1)
Wrench
l (x3)
M8 Washer
m1 (x1)
Wire Clip
n (x1)
Allen Key
p (x8)
M4x12
q (x8)
M4x30
m2 (x4)
Wire Clip
u (x1)
So Pad
r (x8)
M4 Spacer
t (x4)
Rubber Feet
s (x1)
Decorative
Cover
OPTION B: Existing Grommet Base Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a at surface before
installing the desk mount.
1. Attach So Pad (u) to the Pole (a), see Figure 5.
2. Position the pole (a) on the mounting surface and secure using the Support Plate (h), M10 Washer
(i), Spring Washer (j), and M10 Bolt (g). Fasten the M10 Bolt using the provided wrench (o). Insert
the Decorative Cover (s) to the Pole (a), see Figure 6.
OPTION A: Weighted Base Installation
1. Attach Rubber Feet (t) to the Weighted Base (b), see
Figure 1.
2. Attach So Pad (u) to the Pole (a), see Figure 2.
3. Install the Pole (a) to the Weighted Base (b) using M6x10
Bolts (e), Connecting Bolts (k), and M8 Washers (l), and
tighten using the Allen Key (n), insert the Decorative
Cover (s) to the Pole (a), see Figure 3.
4. (Optional) Drill a 10mm diameter hole in your desk
and secure using the Support Plate (h), M10 Washer(i),
Spring Washer (j) and M10 Bolt (g). Fasten the M10 Bolt
with provided Wrench (o), see Figure 4.
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Figure 1 Figure 2
t
u
Figure 3
b
k
l
e
s
a
Figure 4
g
i
h
j
Figure 5
u
Figure 6
g
j
i
h
s
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM

4 5
STEP 1 (Continued)
OPTION C: Self Drilled Grommet Hole Installation
Position the pole (a) on the mounting surface and mark the center hole. Drill a 3/8” (10mm) diameter
hole at the marked position through the mounting surface.
1. Attach so pad (u) to the pole (a), see Figure 7.
2. Position the pole (a) on the mounting surface and secure using the Support Plate (h), M10
Washer (i), spring washer (j), and M10 Bolt (g). Fasten the M10 Bolt using the provided wrench
(o). Insert the Decorative Cover (s) to the Pole (a), see Figure 8.
STEP 3
STEP 2
STEP 4
Slide the monitor with attached VESA Plate (d) onto the head of swivel arm (c) as shown in the diagram.
Install the security nut (f). Make sure the security nut is installed before you rotate the monitor.
OPTION A: Flat Back Monitor OPTION B: Curved Back Monitor
Attach VESA Plate (d) using thumb bolts (p). Attach VESA Plate (d) using bolts (q) and spacers
(r).
Install Swivel Arm (c) to the Pole (a). Fasten the bolt with the supplied Allen Key (n). Attach Wire Clip
(m1, m2) to the Pole (a) and Swivel Arm (c).
Figure 7
u
Figure 8
g
j
i
h
s
c
m2 n
m1
pr
q
f

6 7
STEP 5 STEP 6
Tighten the bolt with the supplied allen key (n) to x the tilt angle. If one monitor is lower, remove the
nut (f) and turn the bolt counter-clockwise with supplied allen key (n) to raise the monitor. Install the
nut (f) aer the adjustment.
Use the supplied allen key (n) to make the necessary adjustments. Manage the wires and store the allen
keys (n) in wire clip (m1) for future use.
n
Fix the tilt angle
Ignore this step if
monitors are level
n
n
m1

Last Updated: 11/27/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654