Vivo STAND-V002VA User manual

Dual Monitor Desk Mount with VESA Adapter Bracket
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002va
SKU: STAND-V002VA
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A (x1)
Pole
B(x1)
Clamp
C(x1)
Swivel Arm
D (x2)
VESA Plate
S-A (x3)
M6x16mm Screw
S-B (x2)
M6 Security
Nut
M-A (x8)
M4x12mm Thumbscrew
E (x1)
Grommet Base Plate
F (x1)
So Pad
G(x1)
Support Plate
H (x1)
Pole Cap
I (x8)
Bracket Arms
J (x8)
“L” Support Holder
K (x1)
Pole Cable Clip
L (x4)
Arm Cable Clip
M-B (x8)
M4x30mm Screw
M-C (x8)
M6 Spacer
T-B (x1)
3mm Allen
Wrench
T-C (x1)
5mm Allen
Wrench
T-D (x1)
6mm Allen
Wrench
M(x8)
Plastic Cover
S-C (x16)
Nut
S-D (x16)
Carriage
Bolt
S-E (x8)
M6x40mm
Screw
S-F (x8)
M6x60mm
Screw
S-G (x8)
M6x80mm
Screw
T-A (x1)
Wrench
ALTERNATIVE MOUNTING
HARDWARE
If Bracket Arms are not used.

3
TOOLS NEEDED 17.6 lbs
Per Arm
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
OPTION A: Desk Clamp Install
Install the Clamp (B) to the Pole (A) using M6x16 Screws (S-A) and tighten using 3mm Allen
Wrench (T-B). Mount Clamp (B) to the desktop and tighten using the hand crank.
ASSEMBLY STEPS
STEP 1
STEP 2
Unscrew the hand crank of Clamp (B) to create an opening for the clamp to placed on desktop.
B
T-B
S-A
B
B

4
STEP 2 - Continued
Install Grommet Plate (E) to the Pole (A) using M6x16 Screws (S-A) and 3mm Allen
Wrench (T-B). Attach So Pad (F) to the Grommet Plate (E).
If desk does not have an existing grommet hole, drill a 3/8” (10mm) diameter hole at the desired
position through the mounting surface. Otherwise, you may use any existing 10-60mm gromment
hole.
Position Pole (A) on the mounting surface
and secure using the Support Plate (G)
and Knob (B1).
OPTION B: Grommet Installation
Separate the Hand Crank (B1) from Clamp (B) by removing the screw with a Phillips screwdriver.
B
B1
A
E
G
A
B1
F
S-A
T-B

5
STEP 3
STEP 4
L
A
T-D
K
C
Slide Pole Cable Clip (K) and Swivel Arm (C) onto Pole (A). Tighten Swivel Arm (C) at desired height
using 6mm Allen Wrench (T-D). Insert Pole Cap (H) into top of Pole (A). Place Cable Clips (L) onto
Swivel Arm (C).
Attach “L” Support Holders (J) to Bracket
Arms (I) using appropriate M6 Screws (S-E,
S-F, or S-G) for monitor thickness and a
Phillips screwdriver. Do not tighten fully.
Connect VESA Plate (D) to assembled arms using Carriage Bolts (S-D), Nuts (S-C),
Wrench (T-A) and a Phillips screwdriver. Arms can be assembled in one of four
methods, which are shown below and on next page.
STEP 5
#1
T-A
D
S-C
S-D
H
S-E/F/G
I
J

6
STEP 5 (Continued)
#2
#3
#4
T-A
S-C
D
S-D
T-A
S-C
D
S-D
T-A
S-C
D
S-D
STEP 6
With all “L” Shaped Holders (J) facing up, place monitor on lower two holders and fully tighten lower
two screws with a Phillips screwdriver. Turn top Holders down and tighten top screws, then tighten
nuts for the upper arms. Install Plastic Covers (M) to cover screws.
JM

7
STEP 7
Slide monitor assembly onto Swivel Arm (C) and secure with M6 Security Screw (S-B). Route cables
through Arm Cable Clips (L) and Pole Cable Clip (K).
To level monitors, remove M6 Security Nuts (S-B) and tighten or loosen adjustment screws using 3mm
Allen Wrench (T-B). Once level, fasten M6 Security Nuts (S-B) back into place. Adjust the monitor tilt
using 5mm Allen Wrench (T-C).
S-B T-B
T-C
S-B
K
L
STEP 8
C
CAUTION:
To avoid risk of monitors sliding o,
DO NOT rotate monitors beyond +5° or -5°.

LAST UPDATED: 01/16/2023
REV1.2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303