VoIPon AG-188 User manual

AG-188 User Manual
AG-188N User Manual
1 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
1AG-188N Features...............................................................................................4
1.1 Appearance.................................................................................................................4
1.2 Interface.......................................................................................................................4
1.3 Electricity characteristic.............................................................................................5
1.4 Software.......................................................................................................................5
1.5 Standard and Protocols.............................................................................................5
1.6 Compliant Standards..................................................................................................6
1.7 Operating requirement...............................................................................................6
1.8 Package.......................................................................................................................6
1.9 Installation....................................................................................................................7
2Web Configuration ...............................................................................................7
2.1 Access Web setting page..........................................................................................7
2.2 Current state................................................................................................................9
2.3 Network......................................................................................................................10
2.3.1 Wan Config ....................................................................................... 10
2.3.2 LAN Config......................................................................................... 11
2.4 VoIP ............................................................................................................................11
2.4.1 SIP Config............................................................................................... 11
2.4.2 Iax2 Config............................................................................................. 13
2.5 Advance.....................................................................................................................14
2.5.1 DHCP Server.................................................................................... 14
2.5.2 NAT................................................................................................... 15
2.5.3 Net Service ....................................................................................... 16
2.5.4 QoS settings ..................................................................................... 17
2.5.5 Advance SIP settings ........................................................................ 18
2.5.6 Digital Map........................................................................................ 19
2.5.7 Call Service Settings.........................................................................20
2.5.8MMI Filter ......................................................................................... 21
2.5.9 Audio Settings...................................................................................22
2.5.10VPN ..................................................................................................22
2.6 Dial-Peer Settings .......................................................................................................24
2.7 Config Manage..........................................................................................................25
2.8 Update........................................................................................................................26
2.9 System Manage........................................................................................................28
2.9.1 Account Manage ...............................................................................28
2.9.2 Syslog Config:...................................................................................28
2.9.3 Time Set:...........................................................................................29
2.9.4 Logout&Reboot.................................................................................29
3IVR setting...........................................................................................................30
4Telnet Console....................................................................................................31
4.1 Introduce....................................................................................................................31
4.2 Global Command......................................................................................................32
5Tree Structure.....................................................................................................33
2 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
6Network Diagnosis.............................................................................................34
7Restore to factory default..................................................................................34
8POST Mode(safe mode)...................................................................................35
9FAQ.......................................................................................................................36
How many SIP servers mayAG-188N register simultaneously? ......................36
How can I know the AG-188N’s IP address?....................................................36
How to use AG-188N’s Lifeline function?.........................................................36
Why the settings vanish after reboot?..............................................................36
How to use the dial rule?.................................................................................36
How to use speed dial function?......................................................................38
How to configure digital map? .........................................................................38
How to use Call Forward, Call Transfer and 3-way Conference calls? .............38
VLAN implement .............................................................................................39
3 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
1 AG-188N Features
1.1 Appearance
PWR：power connection status
SYS : server registration status . registered: on , gliting , not-registered , off
WAN: WAN port connectiong , contected , on , offline : off
LAN: LAN port connectiong , contected , on , offline : off
PSTN: light on when PSTN call come in/out
VoIP: light on when VoIP call come in/out , The default status when pick up the call is VoIP
call out
1.2 Interface
Power: Output Power:12VDC,500mA.
Port: RJ11 port. Connect to handset or the Lifeline accessory.
WAN: RJ45 port.
LAN: RJ45 port.
4 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
1.3 Electricity characteristic
zSpeciality of electric: output the 12V 500mA DC
zThe network connects:2 RJ45 connect, a WAN, a LAN
zFXS: 2 port
1.4 Software
zSupport two sip servers running at the same time.
zBack-up sip server support.
zNAT, Firewall.
zDHCP client and server.
zSupport PPPoE, (used for ADSL, cable modem connecting).
zSupport major G7.xxx CODEC.
zVAD,CNG.
zG.165 compliant 16ms echo cancellation
zTone generation and Local DTMF re-generation according with ITU-T
zE.164 dial plan and customized dial rules
zSupport Lifeline.
zHotline.
zSpeed Dial
zCall Forward, Call Transfer, 3-way conference calls
zCaller ID display
zDND(Do Not Disturb),Black List,Limit List
zUpgrade firmware through FTP or HTTP.
zWeb management.
zReverse polarity
zTelnet remote management.
zVoice prompt
zadjustable user password and super password
1.5 Standard and Protocols
zIEEE 802.3 /802.3 u 10 Base T / 100Base TX
zPPPoE: PPP Protocol over Ethernet
zDHCP Client and Server: Dynamic Host Configuration Protocol
zG.711 u/a; G729 audio Codec
zSIP RFC3261, RFC 2543
zIAX2
zTCP/IP: Internet transfer and control protocol
zRTP: Real-time Transport Protocol
zRTCP: Real-time Control Protocol
zVAD/CNG save bandwidth
5 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
zTelnet: Internet's remote login protocol
zDNS: Domain Name Server
zTFTP: Trivial File Transfer Protocol
zHTTP: Hyper Text Transfer protocol
zFTP: File Transfer protocol
zRFC 3362：T.38 protocol
1.6 Compliant Standards
zCE：EN55024,EN55022
zFCC part15
zcomply with ROHS in EU
zcomply with ROHS in China
z
Explanation:
The letter “e” is the first letter of “environment: and “electronic”, The rim is a round with two
arrow , stands for recycle. The number 20 stands for the years of environment protection.
Please note the years of environment protection is not discarding year nor usage life
1.7 Operating requirement
●Operation temperature: 0 to 40° C (32° to 104° F)
●Storage temperature: -30° to 65° C (-22° to 149° F)
●Humidity: 10 to 90% no dew
1.8 Package
zSize 128 x 85 x 30 mm
zPacking List
9AG-188N gateway
9Power adaptor (12v, 500mA)
9Manual CD
6 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
1.9 Installation
Use Ethernet cable to connect AG-188N’s LAN port and your computer. Set your
computer’s ip to the network 192.168.10.x or using dynamic obtain IP. Open your web
browser and key in 192.168.10.1. Then you will see the logon page of AG-188N, the
default username and password is admin/admin for administrator and guest/guest for
guest.
Set up page for VoIP use only:
PSTN
Internet
POS Phone
Power
PBX
User
2 Web Configuration
2.1 Access Web setting page
Enter AG-188N IP address in the web browser and press ENTER to go to the log on page,
and key in the username and password to access AG-188N setting page.
Default username and password is:
Administrator: Username: admin password: admin
User: Username: guest Username: guest
7 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
8 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
2.2 Current state
This page showsAG-188N’s running state.
Network ：shows the WAN and LAN port connecting state and current settings.
VoIP：show the default protocol, the working state of SIP and IAX2, you can see whether
AG-188N has registered the public sip server and IAX2 server.
Phone Number shows the public sip server、the private sip server and the IAX2 server
phone numbers.
9 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
2.3 Network
2.3.1Wan Config
WAN port network setting page.
Support static IP, dynamic obtain IP and PPPoE.
Configure Static IP:
----Enable Static;
----Set AG-188N’s IP address in the IPAddress;
----Set net mask in the Net mask field;
----Set router IP address in the Gateway;
----DNS Domain:
----Set local DNS server in the Preferred DNS and the Alternate DNS
Configure to dynamic obtain IP
----Enable DHCP;
If there is DHCP server in your local network, AG-188N will automatically obtain WAN
port network information from your DHCP server.
Configure PPPoE:
----Enable PPPoE
----PPPoE server: Enter “ANY” if no specified from your ITSP.
----Enter PPPoE username and pin in the username and password.
AG-188N will automatically obtain WAN port network information from your ITSP if
PPPoE setting and the setup are correct.
Notice: If user accesses the gateway through WAN port. He should use the new IP
address to access the gateway when the WAN port address was changed.
10 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
2.3.2 LAN Config
Bridge Mode: Enable this option to switch to bridge mode. Gateway won’t assign IP
for its LAN port in bridge mode and its LAN and WAN port will be in the same network.
(This setting won’t take effect unless you save the config and reboot the device)
IP Netmask: Set the IP and Netmask for the LAN
DHCP Server: Enable DHCP service in LAN port
NAT: Enable NAT.
2.4 VoIP
2.4.1 SIP Config
Setting page of public SIP server:
Register Server Addr: Register address of public SIP server
Register Server Port: Register port of public SIP server
Register Username: Username of your SIP account (Always the same as the phone
number)
Register Password: Password of your SIP account.
11 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
Proxy Server Addr: IP address of proxy SIP server (SIP provider always use the
same IP for register server and proxy server, in this case you don’t need to configure the
proxy server information. )
Proxy Server Port: Signal port of SIP proxy
Proxy Username: proxy server username
Proxy Password: proxy server password
Domain Realm: SIP domain, enter the sip domain if any, otherwise AG-188N
will use the proxy server address as sip domain.
Local SIP port: Local SIP register port, default 5060
Phone Number: Phone number of your SIP account
Register Expire Time: register expire time, default is 600 seconds. AG-188N will auto
configure this expire time to the server recommended setting if it is different from the SIP
server.
Detect Interval Time:Co-work with the Auto Detect Server, if Auto Detect Server is
enable, AG-188N will periodically detect if the SIP server is available according this
setting.
RFC Protocol Edition: Current AG-188N SIP versions. Set to RFC 2543 if the gate
need to communicate to devices (such as CISCO5300) using the SIP 1.0. Default is RFC
3261.
Enable Register: Enable/Disable SIP register. AG-188N won’t sent register info to
SIP server
DTMF Mode:DTMF signal sending mode: support RFC2833, DTMF_RELAY (inband
audio) and SIP info
Auto Detect server: co-work with Server Auto Swap and Detect Interval Time. Enable
this option, AG-188N will periodically detect whether the public SIP server is available, if
the server is unavailable, the AG-188N will switch to the back-up SIP sever, and continue
detecting the public sip server. AG-188N will switch back to the primary SIP server if the
server is available again.
Server Auto Swap:Please refer to Auto Detect server for detail.
Enable Via rport: config the supporting for RFC 3581
SIP(Default Protocol): Setting for the default protocol of SIP
12 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
2.4.2 Iax2 Config
Setting page of public IAX server:
IAX Server Addr: Register address of public IAX server
IAX Server Port: Register port of public IAX server，default port is 4569
Account Name: Username of your SIP account (Always the same as the phone
number)
Account Password:Password of your IAX account.
Local port: Signal port of local, default port is 4569
Phone Number: Phone number of your IAX account
Voice mail number: If the IAX support voice mail, but your username of the voice mail is
letters which you can not input with the ATA , then you use the number to stand for your
username
Voice mail text: if IAX support voice mail, config the domain name of your mail box here.
Echo test number: If the platform support echo test , and the number is test form , the
config the test number to replace the text format The echo test is to test the woring status
of terminals and platform
Echo test text: echo test number in text format
Refresh time: IAX refresh time
Enable Register: enable or disable register
IAX(Default Protocol): Set IAX 2 as the default protocol , if not the system will choose SIP
as default
Enable G.729: Using G.729 speech coding mandatory consultations
13 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
2.5 Advance
2.5.1 DHCP Server
DHCP server manage page.
User may trace and modify DHCP server information in this page.
Update Mode: Using DHCP updated model ,None expressed are not updated,
Update firmware update firmware is used to DHCP. Update file is used to
configure DHCP updated configuration files.
Tftp Server: Addresses using TFTP server upgrade 。
DNS Relay: enable DNS relay function.
User may use below setting to add a new lease table.
Lease Table Name: Lease table name.
Lease Time: DHCP server lease time.
Start IP: Start IP of lease table.
End IP: End IP of lease table. Network device connecting to the AG-188N LAN port can
dynamic obtain the IP in the range between start IP and end IP.
Netmask: Netmask of lease table.
Gateway: Default gateway of lease table
DNS: default DNS server of lease table.
Notice: This setting won’t take effect unless you save the config and reboot the device
14 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
2.5.2 NAT
Advance NAT setting. Maximum 10 items for TCP and UDP port mapping.
IPSec ALG: Enable/Disable IPSec ALG;
FTP ALG: Enable/Disable FTPALG;
PPTP ALG: Enable/Disable PPTPALG;
Transfer Type: Transfer type using port mapping.
Inside IP: LAN device IP for port mapping.
Inside Port: LAN device port for port mapping.
Outside Port: WAN port for port mapping.
Click Add to add new port mapping item and Deleteto delete current port mapping item.
15 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
2.5.3 Net Service
HTTP Port: configure HTTP transfer port, default is 80.User may change this port to enhance
system’s security. When this port is changed, please use http://xxx.xxx.xxx.xxx:xxxx/ to
reconnect.
Telnet Port: configure telnet transfer port, default is 23.
RTP Initial Port: RTP initial port.
RTP Port Quantity: Maximum RTP port quantity, default is 200
Notice:
Settings in this page won’t take effect unless save and reboot the device.
If you need to change telnet port or HTTP port, please use the port greater than 1024,
because ports under 1024 is system remain ports.
HTTP service if HTTP is set to 0.
16 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
2.5.4 QoS settings
AG188 implement QoS based on 802.1p, The QoS is used to mark the network
communication priority in the data link/MAC sub-layer. AG188 will sorted the packets
using the QoS and sends it to the destination.
1. Voice 802.1p Priority --- Configure the priority of the voice packets in 802.1p protocol.
2. VLAN Enable --- Disable/Enable VLAN function
3. Voice VLAN ID --- configure the Voice/signaling VLAN ID
4. DiffServ Enable --- Disable/Enable Diffserv service
5. DiffServ Value --- Configure Diffserv parameter. The value range : value range：
0x28,0x30,0x38,0x48,0x50,0x58,0x68,0x70,0x78,0x88,0x90,0x98,0xb8.default is
0xb8 ,oxb8 stands for best fast transmission; 28-30 is guaThrantee for the transmission
priority for the 1st rank , 48-58 is guarantee for the transmission priority for the 2nd rank,
68-78 is guarantee for the transmission priority for the 3rd rank, 88-98 is guarantee for the
transmission priority for the 4th rank.
6. Data VLAN ID--- Assign VLAN id for data stream.
7. Data 802.1P Priority --- Configure the priority of the data packets (non-voice/signaling
data) in 802.1p protocol.
8. Data/Voice DiffServ differentiated --- undifferentiated for Date and voice VLAN is not
distinction VLAN tag, Tag differentiated for Date and Voice VLAN is distinction VLAN tag,
Date untagged for Date VLAN is distinction VLAN tag
Please refer to VLAN implement for detail
17 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
2.5.5 Advance SIP settings
This page is used to set the private sip server, stun server, and back up sip server
information.
STUN Server setting:
STUN Server Addr: configure stun server address;
STUN Server Port: configure stun server port default 3478
STUN Effect Time: stun detect NAT type circle, unit: minute.
Enable SIP STUN: enable/disable stun.
Please refer to sip conf for the setting for how to set the public alter server.
Private Server Type：The particular Private service system supplier carries out the sign
and speeches to encrypt, default is common
User can register two sip servers: public sip server and private sip server. these two sip
servers are independent from each other and running in the same time.
For how to configure private sip server. Please refer to sip configuration.
18 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
2.5.6 Digital Map
Digit map is a set of rules to determine when the user has finished dialing.
AG-188N support below digital map:
Digital Map is based on some rules to judge when user end their dialing and send the number to
the server. AG-188N support following digital map:
----End With “#”: Use # as the end of dialing.
----Fixed Length: When the length of the dialing match, the call will be sent.
----Timeout: Specify the timeout of the last dial digit. The call will be sent after timeout
----Prefix: User define digital map:
[ ] represents the range of digit, can be a range such as [1-4], or use comma such as [1,3,5],
or use a list such as [234]
x represents any one digit between 0~9
Tn represents the last digit timeout. n represents the time from 0~9 second, it is necessary.
Tn must be the last two digit in the entry. If Tn is not included in the entry, we use T0 as default, it
means system will sent the number immediately if the number matches the entry.
Example:
[1-8]xxx All number from 1000 to 89999 will be sent immediately.
9xxxxxxx 8 digits numbers begin with 9 will be sent immediately.
911 Number 911 will be sent will be immediately
99xT4 3 digits numbers begin with 99 with be sent after four seconds.
19 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

AG-188 User Manual
2.5.7 Call Service Settings
User configure the value add service such as hotline, call forward, call transfer, 3-way
conference call .etc in this page
Hotline: configure hotline number. AG-188N immediately dials this number after hook-off
if it is set.
Call Forward: Please refer to value add service for detail.
No Disturb: DND, do not disturb, enable this option to refuse any calls.
Ban Outgoing: Enable this to ban outgoing calls.
Enable Call Transfer: Please refer to value add service for detail.
Enable Three Way Call: Please refer to value add service for detail.
Enable Call Waiting: Enable/disable Call Waiting
Accept Any Call:If this option is disable, AG-188N refuse the incoming call when the
called number is different fromAG-188N’s phone number.
No Answer Time: no answer call forward time setting.
Black List: incoming call in these phone numbers will be refused.
Limit List: outgoing calls with these phone numbers will be refused
20 / 42
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]