vollara STEADY POWER User manual
STEADY
POWER
U.S. PATENT D615506
POWER CONDITIONING SYSTEM
CAUTION: Read manual carefully for proper procedures and operation.
WARNING:
1. Opening the unit without prior permission
from Vollara will void its warranty coverage.
Contact Vollara at 1.800.989.2299 if you
have any questions.
2. Apply this unit to 120V AC 60Hz, single phase
load only.
3. The unit must be mounted vertically, in a dry
location, using the four provided mounting clips.
4. WARNING! THIS UNIT MUST BE INSTALLED
BY A LICENSED ELECTRICIAN (IN
COMPLIANCE WITH LOCAL ELECTRICAL
CODES). FAILURE TO DO SO COULD
RESULT IN DEATH OR SERIOUS INJURY.
5. IMPORTANT! This unit must be connected
directly to a dedicated circuit breaker. Do not,
under any circumstances, hard-wire install
without a dedicated breaker!
6. Proper installation of this unit requires
the dedicated breakers (two (2) single
pole, 20 amp breakers required) to be
installed in breaker positions 1 and 2 (upper
most positions in the breaker panel).
NOTE: If these positions are already in
use in your breaker panel, the electrician
must relocate the circuits that currently
occupy these positions (positions 1 and
2) to open positions located lower in the
breaker panel. FAILURE TO FOLLOW THIS
INSTALLATION PROCEDURE WILL VOID
YOUR WARRANTY !
YOU WILL NEED:
1. Two (2) dedicated, single pole, 20 amp circuit
breakers.
2. Appropriate tools including conduit.
3. A licensed electrician for installation.
MOUNTING THE STEADYPOWER FLUSH-
MOUNT (ECP240R)
WARNING! THIS UNIT MUST BE INSTALLED BY
A LICENSED ELECTRICIAN (IN COMPLIANCE
WITH LOCAL ELECTRICAL CODES). FAILURE
TO DO SO COULD RESULT IN DEATH OR
SERIOUS INJURY. DE-ENERGIZE POWER PANEL
(WE RECOMMEND TURNING OFF THE MAIN
POWER BREAKER) PRIOR TO BEGINNING THIS
PROCEDURE.
NOTE: For surface mounted applications, you will
need a surface mounting adapter plate. See your
Vollara Independent Business Owner for more
information.
1. Inspect the exterior of the unit to ensure that it
has not been damaged in transit. Ensure that
the front label/overlay is still intact, and that
the cables protruding from the unit have not
been damaged.
2. Place the back of the Flushmount Box against
wall where the unit is to be installed and trace
around its outside edge. Cut drywall along
traced line (dimension of traced area should
be approximately 4.866” wide by 8.250” high).
3. Run conduit (according to code) between the
conduit connector on the box and the power
panel, and feed the connection cables through
the conduit into the power panel.
4. Secure the four (4) clips to the mounting box
and tighten screws to tightly fit.
5. Screw Cover Plate onto unit.
INSTALLATION PROCEDURES:
1. De-energize power panel prior to connection
of the Steady Power unit (we recommend
turning off the Main Power Breaker).
2. Install the two (2) single pole, 20 amp circuit
breakers into circuit positions 1 and 2 (see
item 6 in “Warning Section” above) of the
circuit panel.
3. Connect the RED wire (L1) to the circuit
breaker located in position 1, the BLACK wire
(L2) to the circuit breaker located in position 2,
the GREEN with yellow stripe wire (Ground) to
the ground bus, and the WHITE wire (Neutral)
to the neutral bus, as shown in the diagram
on page 3.
Voltage:
120V AC 60Hz, 2.7 A
Configuration:
3-wire plus ground
Capacitance: 30µf
Line Current: 2.7 A
KVA Rating: .65 at 240V AC
TEST PROCEDURES:
1. Energize the power panel.
2. Close the circuit breaker leading to the
SteadyPower unit.
3. Check if Line 1 and Line 2 indicator lights are on:
IF NO - De-energize the power panel and check if
cables are connected correctly.
Check the ground cable connections.
If problem persists, call Vollara at
1.800.989.2299.
4. Keep these instructions near the unit for
future use.
LINE
RED BLACK
GREEN
WHITE
L1
L1
L2
NEU
BUS
GND
BUS
20A
BREAKER L2
20A
BREAKER
POWER PANEL
ECP240R
INSTALLATION
DIMENSIONS FOR THE STEADYPOWER FLUSHMOUNT (ECP240R)
8.2509.750
4.866
4.746
2.875
MOUNTING
CLIPS (4X)
FOR
FLUSHMOUNT
STEADY
POWER
ECP240R
VOLLARA | 300 EAST VALLEY DRIVE | BRISTOL, VA 24201 | 800.989.2299
CE DECLARATION OF CONFORMITY
We, on behalf of the manufacturer: Vollara, LLC
300 East Valley Drive
Bristol, VA 24201
U.S.A.
Declare under our sole responsibility, that the Energy Management Device
Model: SteadyPower ECP240R
to which this declaration relates, conforms with the following standards:
EN60950-1:2006 Safety of Information Technology Equipment - General
Requirements
By conformance with the standards referenced, the product meets the provisions of
the EU Directives listed below:
Low Voltage Directive 73/23/EEC as amended by
98/68/EEC
RoHS Directive 2002/95/EC
WEEE Directive 2002/96/EC
Authorized by:
Representative: Andy Eide
Title: Vice President, Product Development and Research
Company: Vollara, LLC
300 East Valley Drive
Bristol, VA 24201
Date: 4/3/2018
SP_OM_65-00667_VA-01032_0418
Part No. 65-00667
