vwin VJ201-S3 User manual

Manufacturer: Ningbo VWIN Smart Tech Co.,Ltd.
Tel: [phone]
Email: [email protected]
Website: vwindesk.com
Electric Standing Desk
VJ201-S3
Electric Height Adjustable
Standing Desk Frame
Please register the product
for 5-year warranty
See page 9
Scan it

www.vwindesk.com

CAUTION/INFORMATION
Make sure no obstacles are in the desk's path.
Make sure the desktop is not touching any walls.
Make sure all cords are appropriate length to
accommodate the change in height.
WARNING
PINCH POINT
keep hands and
fingers clear.
Keep children away from electric height-adj ustable desks,
control units and handsets. There is a risk of injury and electric shock.
Keep all electrical components away from liquids.
Do not set or stand on the desk Frame.
Do not crawl or lie under the desk Frame.
Do not place any objects taller than 50 underneath the desk.cm
This product is designed with a duty cycle of 10% (2 min. on, 18 min. off)
In the event of a power outage or if the power cord is unplugged,
a manual reset may be necessary - see Step 12.
USE/LIABILITY
This height adjustable desk has electric motors and is designed for use in dry work areas only. The
desk height is adjustable so that it can be positioned at the most ergonomically suitable height.
Any other use is at user's risk.
Under no circumstances does the manufacturer accept warranty claims or liability claims for damages
caused from improper use or handling of the desk frame.
IMPORTANT:
Please read this manual carefully.
If this desk is sold ,please provide this manual to the buyer.
Do not open any of the components - the Legs, control Box, or handset.
There is a danger of electric shock.
Page 1
www.vwindesk.com
www.vwindesk.com

PARTS
Foot with
GlidesCrossbar EndCenter RailSide Bracket
Control Box Programmable
Handset
Power cord
Cables:60cm
Machine Screws:
M6x12
x16
Cable Clips
Machine Screws:
M6x10
x8 x10
4MM Allen Wrench
(included)
Head Screwdriver
and/or Power Drill
Tape measure
Legs
x2 x2 x2 x2 x2
x1 x1 x2 x1
Wood Screws:
ST M5x16
x8 x4
Top Screws:
M6*35
TOOLS REQUIRED
COMPONENTS
HARDWARE
No. Description Qty
1 Crossbar Center Rail 2
2 Crossbar End 2
3 Side Bracket 2
4 Leg 2
5 Foot 2
6 Foot Glides 4
7 Machine Screws:M6x12 16
8 Machine Screws:M6x10 8
9 Top Screws:M6*35 4
10 Programmable Handset 1
11 Control Box 1
12 Cables 2
13 Power Cord 1
14 Wood Screws:ST M5x16 8
15 Cable Clips 10
Page 2
Register Your Desk
1．Scan the QR Code by your smart phone ( iPhone or Android),
it will jump to our website product registration page.
2．The Series Number will be auto-filled on the page.
Just fill your name and your email address. Then Click submit.
3．Our Sales support will email you the detail information about the
desk and the 5 years Warranty.
Find the QR Code on the Front Cover
Or
On the Desk Leg
Contact Us for help
and request Serivce
1. Call us [phone]
2. Visit our website https://vwindesk.com/
contact/Fill the contact form quickly
3. Our email address: [email protected]
After you have registered your desk, We can supply quick services according to your
email address. Because we have your desk information in our system, the production
date, the model number, the components batch number etc.
Not just for the 5 years warranty, if we find any components have risks on using, we
will take actions like automotive industry. You will be informed and send you a replace
components.
So please don’t ignore the requirement of registration of your desk.
Page 9
www.vwindesk.com
www.vwindesk.com

Place one of the Legs (Part #4) into the Crossbar End (Part #2)
Line up the holes on each Leg (Part #4) with the holes on each
Crossbar End (Part #2)
Using the Allen Wrench, rotate each screw just a few turns.
If you are having diy insg any of the
screws from Step 3 or 4, it is because some of
the installed screws are too ht.
Lay out all components and hardware to ensure that you have all components and hardware listed on the
parts page.
Fully separate the Crossbar Ends (Part #2). You will d the Crossbar Center Rails (Part #1) inside.
Using the supplied Allen Wrench, insert four (4) M6x12 Machine
Screws (Part #7 ) through the holes in each Crossbar End (Part #2) going
into the Leg (Part #4) and rotate each screw just a few turns.
You will need to dip the assembly over to gain access to all four (4) M6x12
Machine Screws (Part #7 ) .
ASSEMBLY INSTRUCTIONS

Tighten the screws M6 X 35(Part #9 ) from the top.
STEP1
STEP2
STEP3
If you drop a screw inside the Crossbar End (Part #2), simply tilt
to retrieve the screw.
Page 3
USE INSTRUCTIONS
Error Code Key
Code Meaning Suggested Actions
E01 Power supply Troubles Change the Control box
E03 Unbalance more than 10mm Reset the desk
E04 Unconnected to the handset Plug into the control box
E05 Anti-collision stop Release then use again
E06 Main power damage Change the Control box
E07 Active power protection Re-plug the power
E08 Unbalance of the desktop Reset the desk
E09 Overheated Let the desk cool down for 20 minutes
E11/21 Unconnected with motor M1/M2 Check the cables connection
E12/22 Communication error M1/M2 Change the control box
E13/23 Motor power cable connection issue
M1/M2
Replace the motor or control box
E14/24 Motor sensor errorM1/M2 Change the Motor
E15/25 Motor damage M1/M2 Change the Motor
E16/26 Motor blocked M1/M2 Reset the desk
E17/27 Motor errorM1/M2 Change the Motor
E18/28 Overloaded Reduce weight on the desk
Page 8
visit our website vwindesk.com/contact for help
call us [phone]
www.vwindesk.com
www.vwindesk.com

USE INSTRUCTIONS
Up & Down Movement:
Press the UP arrow continuously, the legs will move up
Press the DOWN arrow continuously, the legs will move down
Release arrows to stop movement.
Memory Preset Positions:
Use the UP and DOWN arrows to set table at a desired height.
Press the POSITION SETTING BUTTON (S) followed by one of the 4 PRESET POSITION
BUTTONS(1 2 3 4) buttons. The memory position is set.
There are up to 4 presets available. To return to a memory preset press the desired number.
Reset:
Press the DOWN button and lower the desk to its lowest setting..
Press the DOWN Button again for ~ 5 seconds until the LED reads “RST”
Press the DOWN button & hold it while the legs move up & down to level and stop.
Release the DOWN button as the control box a “Bi--” sound,the reset is now complete
and your table is ready to use.
Page7
Child lock
Press the up arrow and down arrow at the same time for 5 seconds, and then release
the sound when the control box makes a “Bi--” sound.The handset displays “---” and
the table enter the Child lock mode.
Unlock
Press the up arrow and down arrow at the same time for 5 seconds, and then release the
sound when the control box makes a “Bi--” sound. The handset displays the number and
the table exit the lock mode.
Page 7
Slide the two (2) Crossbar center Rails (Part #1)
into the two Crossbar Ends, (Part #2)
ensuring:
a) the slots Face inward
b) the slot is closer to top edge of the
Crossbar center Rail (Part #1) when
the assembly is upside down (see inset)
For each leg, aach a foot (Part #5) with
four (4) M6x12 Machine Screws (Part #7 )
and hten screws in a cross paern.
Check both sides of the desktop before placing
your desk base on the underside of the desktop.
Your desktop may or may not be pre-drilled.
Adjust the width of the desk base to t the
desktop by sliding the two halves outward.
We recommend leaving at least-3cm of the desktop
width (on each end) protruding beyond the
frame width and centered to the base
Lock the posn of the Crossbar center Rails (Part #1）
using eight (8) M6x10 Machine Screws (Part #8 ).
Remember,maximum width is 180cm.
Ensure that the M6x10 Machine Screws (Part #8 ) contacts the A center Rails (Part #1)
by sliding the center Rails (Part #1) as needed.
ASSEMBLY INSTRUCTIONS
STEP4
STEP5
STEP6
STEP7
Page 4
www.vwindesk.com
www.vwindesk.com

ASSEMBLY INSTRUCTIONS
Double-check that the wood screws are not- too long for your desktop
and won't puncture the surface when screwed all the way in.
Double-check that the desk base is properly posd on the underside of the desktop.
Do not ovhten screws in this step.
Ovhtening could cause damage to the components.
Connect the:
Cables (Part #12),Handset Cable (Part #10),
and the Power Cord (Part #13) to the control Box (Part #11)
as per the diagram. Use the adhesive-backed Cable Clips
(Part #15) to secure the Cables and Switch cable,
so they don't- sag.
Turn the assembled desk right side-up. With two people grab the desk BY THE DESK BASE (not the desktop)
and turn the desk right-line-up. Adjust the Glides on the Feet (Part #6 ) as needed.
STEP8
STEP9
STEP10
Page5
ASSEMBLY INSTRUCTIONS
TECHNICAL SPECIFICATIONS
Plug the Power Cord into a 110v-240v outlet.
Make sure no obstacles are in the desk's path.
Make sure the desktop is not touching any walls.
Make sure all cords are appropriate length to accommodate the change in height
Height Range
Basewidth
Travel Speed
Weight capacity
Duty Cycle
(without desktop)
(no load)
10%. Max. 2 mins on, 18 mins o
Sostart/stop
Adjustable leveling studs
4 Memory presets
STEP11
23.6 - 49.2 inch
43.3 - 70.9 inch
1.5 inch/second
320 lbs
Page6
Attach the desk base to the underside of the desktop
using eight (8) M5x16 ST Screws (Part #14):
2 per Side Bracket (Part- #3) - 4 total
1 per Crossbar End (Part #2) - 2 total
The New Design tcontrol box(part#11) has never use screws,
On one Crossbar End(part#2), there is a designed Latch Pin, The back of
the control box has a matched groove, just insert the control box
to the latch pin, it crossbar End.
Place the Programmable handset (Part #10) so

edge (or recessed up to 0.4cm). The handset may be placed
anywhere along the front edge of your desktop but we
recommend placing if toward an end so does not
interfere with your chair when seated.
Use two (2) M5x16 Screws (Part #14) to attach the
Handset to the desktop.
Use two (2) M5x16 Screws (Part #14) or nano adhesive tape 
Latch Pin

error code; You must RESET the desk prior to use.


"di" sound the reset is compleated and your table is ready to use;
www.vwindesk.com
www.vwindesk.com