W Box Technologies WBXID134RT User manual

T E CHNO L OG IES
www.wboxtech.eu
BOX
WBXID134RT
WBXID204RT
WBXID304RT
WBXID136VRT
WBXID206VRT
WBXID306VRT
WBXIL139RT
WBXIL209RT
WBXIL309RT
WBXIL136RT
WBXIL206RT
WBXIL306RT

2
Contents
Contents.....................................................................................................................................................................................2
Warranty ....................................................................................................................................................................................3
Regulatory Information..............................................................................................................................................................5
Appearance Description.............................................................................................................................................................5
Installation..................................................................................................................................................................................7
1. Ceiling Mounting.........................................................................................................................................................8
2. Micro SD Card Installation ........................................................................................................................................10
3. Installation of Water-proof Jacket (supplied)...........................................................................................................13
Accessing via Web Browser......................................................................................................................................................13
Live View ..................................................................................................................................................................................15
Specifications ...........................................................................................................................................................................17

3
The content in this manual is subject to change without notice. Updates will be added to future versions of this manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or signaling aspects of
this product. UL has only tested for fire, shock or casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-
1. UL Certification does not cover the performance or reliability of the security or signaling aspects of this product. UL
MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR
RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.
Warranty
1. Limited Warranty
a. General
Subject to the terms and conditions of this Limited Warranty, from the date of sale by ADI to the Buyer through the period
of time for product categories specified in Section 1(b), ADI warrants its W Box Technologies products to be free from
defects in materials and workmanship under normal use and service, normal wear and tear excepted. Except as required
by law, this Limited Warranty is only made to Buyer and may not be transferred to any third party.
ADI shall have no obligation under this Limited Warranty or otherwise if:
(i) The product is improperly installed, applied or maintained;
(ii) The product is installed outside of stated operating parameters, altered, or improperly services or repaired;
(iii) Damage is caused by outside natural occurrences, such as lightning, power surges, fire, floods, acts of nature, or
the like.
(iv) Defects resulting from unauthorized modification, misuse, vandalism, or other causes
unrelated to defective materials or workmanship, or failures related to batteries of any type used in connection with the
products sold hereunder.
ADI only warrants those products branded as W Box Technologies products and sold by ADI. Any other products branded
by third parties are warranted by the third party manufacturer for a period as defined by the third party manufacturer,
and ADI makes available or assigns to Buyer those warranties and only those warranties extended by such third party
manufacturers or vendors for non-ADI branded products to the extent that ADI has the right to such warranties or is
entitled to assign them. ADI does not itself warrant any non-ADI branded product and sells only on an as is basis in
accordance with ADI’s terms and conditions of sale.
b. Specific Warranties for product categories are as follows:
Product Categories
Warranty Period
Analog Cameras
36 months
CCTV Power Supplies
24 months
Monitors
30 months
DVR's, NVR's
60 Months
IP Cameras
60 Months
TV Mounts
60 months
Analog Cables
Limited Lifetime
B Connectors
Limited Lifetime
HDMI Cables
Limited Lifetime
Patch Cables
Limited Lifetime
Wire Ties
Limited Lifetime
2. EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY
THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A

4
PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. TO THE
FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL ADI BE LIABLE TO ANYONE FOR ANY (I) CONSEQUENTIAL,
INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES AND (II) ANY LOSS OR CORRUPTION OF DATA, ANY LOSS OF
GOODWILL, REPUTATION, PROFITS, ANTICIPATED PROFITS, REVENUE, BUSINESS, CONTRACT, USE OF MONEY OR USE OF
PRODUCT OR ASSET OR ANY LOSS ARISING FROM BUSINESS INTERRUPTION (IN EACH CASE WHETHER DIRECT OR
INDIRECT TO THE EXTENT THAT THESE ARE NOT INCLUDED IN (I)) ARISING OUT OF OR RELATING IN ANY WAY TO THE
PRODUCT AND.OR FOR BREACH OF THIS OR ANY OTHER WARRANTY OR CONDITION, EXPRESS OR IMPLIED, OR UPON ANY
OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY ADI’S OWN NEGLIGENCE OR
FAULT AND EVEN IF ADI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR DAMAGES. Any product description
(whether in writing or made orally by ADI or ADI’s agents), specifications, samples, models, bulletin, drawings, diagrams,
engineering sheets, or similar materials used in connection with the Buyer’s order are for the sole purpose of identifying
ADI’s products and shall not be construed as an express warranty or condition. Any suggestions by ADI or ADI’s agents
regarding use, applications or suitability of the products shall not be construed as an express warranty or condition unless
confirmed to be such in writing by ADI. ADI does not represent that the products it sells may not be compromised or
circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise,
or that the products will in all cases provide adequate warning or protection. Buyer understands and will cause its
customer to understand that a properly installed and maintained product is not insurance or guarantee that such will not
cause or lead to personal injury or property loss. CONSEQUENTLY TO THE FULLEST EXTENT PERMITTED BY LAW, ADI
SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON ANY CLAIM AT ALL
INCLUDING A CLAIM THAT THE PRODUCT FAILED TO GIVE WARNING. However, if ADI is held liable whether directly or
indirectly for any loss or damage with respect to the products it sells, regardless of cause or origin, its maximum liability
shall not in any case exceed the purchase price of the product, which shall be fixed as liquidated damages and not as a
penalty and shall be the complete and exclusive remedy against ADI.
3. Limitation on Liability to Buyer’s Customers.
Buyer agrees to limit liability to its customers to the fullest extent permitted by law. Buyer acknowledges that ADI shall
only be deemed to give consumers of its products such statutory warranties as may be required by law and at no time
shall Buyer represent to its customers and/or users of ADI products that ADI provides any additional warranties. By
accepting the products, to the fullest extent permitted by law, Buyer assumes all liability for, and agrees to indemnity and
hold ADI harmless against and defend ADI from, any and all suits, claims, demands, causes of action and judgments
relating to damages, whether for personal injury or to personal property, suffered by any person, firm, corporation or
business association, including but not limited to, Buyer’s customers and/or users of the products because of any failure of
the products to detect and/or warn of the danger for which the goods were designed or any other failure of the products
whether or not such damages are caused or contributed to by the sold or joint concurring negligence or fault of ADI.
4. Returns
Subject to the terms and conditions listed below, during the applicable warranty period, ADI will replace Product or
provide a credit at purchase at its sole option free of charge any defective products returned prepaid. Any obligations of
ADI to replace Limited Lifetime warranty products pursuant to this warranty which result from defect are limited to the
availability of replacement product. ADI reserves the right to replace any such products with the then currently available
products, or provide a credit in its sole discretion. In the event Buyer has a problem with any ADI product, please contact
your local ADI branch for return instructions:
www.adiglobal.com
www.wboxtech.eu
Be sure to have the model number and the nature of the problem available. In the event of replacement, the return
product will be credited to Buyer’s account and a new invoice issued for the replacement item. ADI reserves the right to
issue a credit only in lieu of replacement.
If any W Box Technologies product is found to be in good working order or such product’s inability to function properly is a
result of user damage or abuse, the product will be returned to Buyer in the same condition as received and Buyer shall be
responsible for any return freight changes.

5
5. Governing Law
The laws of EU apply to this Limited Warranty.
6. Miscellaneous
Where any term of this Limited Warranty is prohibited by such laws, it shall be null and void, but the remainder of the
Limited Warranty shall remain in full force and effect.
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
users will be required to correct the interference at their own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with
the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC
Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
Municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the
purchase of equivalent 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of
as unsorted municipal waste in the European Union. For proper recycling, return this product to your local
supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more
information, see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal
waste in the European Union. See the product documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For
proper recycling, return the battery to your supplier or to a designated collection point. For more information,
see: www.recyclethis.info.
Appearance Description
No.
Description
1
Lens
2
Sun Shield
3
Power Interface
4
Network Interface
DC12VIN
1
2
3
4

6
No.
Description
1
Mounting Base
2
Horizontal Stand
3
Vertical Stand
4
Bubble
5
Network Interface
6
Power Interface
7
IR LED
8
Lens
9
Black Liner
10
Safety Rope
No.
Description
1
Sun Shield
2
Front Cover
3
Zoom and Focus Lever
4
IR LED
5
Lens
1
2
3
4
9
6
7
8
5
10
11
5
12
3
8
6
10
9
7
4
1
2

7
6
Air Vent
7
Video Output Interface
8
Integrated Bracket
9
Reset Button
10
Micro SD Card Slot
11
Power Interface
12
Network Interface
No.
Description
1
Inner Housing
2
Bubble
3
Network Interface
4
Power Interface
5
Reset Button
6
SD Card Slot
7
Lens
8
Mounting Base
NOTE:
Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user
name, password, IP address, port No., etc.
Installation
Before you start:
Make sure the device in the package is in good condition and all the assembly parts are included.
Make sure all the related equipment is power-off during the installation.
Check the specification of the products for the installation environment.
Make sure the power supply is matched with your required voltage to avoid damage.
If the product does not function properly, please contact your dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
2
134
78
5
6

8
Make sure that the wall is strong enough to withstand three times the weight of the camera.
NOTE:
For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection:
Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation
is finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol.
Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back
into the lens causing reflection.
The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR
LEDS. Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly.
1. Ceiling Mounting
Steps:
a) Drill the screw holes on the ceiling according to the drill template.
b) For dome camera, loosen the set screws with a hex key (supplied) to remove the bubble.
c) Fix the mounting base on the ceiling (wall) with screws.
Drill Template
Hole A: for cables routed through the ceiling
screw hole 1: for Mounting Base
1
1
1
A

9
d) Loosen the tilt lock screws, adjust the pan angle and tilt angle.
0°~360°
0°~65°
Tilting Adjust
Screw

10
e) For dome camera, reinstall the bubble and tighten the screws.
2. Micro SD Card Installation
This section is available for cameras which support SD card.
Steps:
a) Loosen the lock screws on the bubble (housing) to disassemble the camera.
0°~100°
0°~360°
0°~360°
0°~360°
0°~90°
0°~360°

11
b) Insert the micro SD card to the card slot.
c) (Optional) Push the inserted micro SD card inside, and the micro SD card will be sprung out.

12
d) Install the bubble (housing) back, and tighten the lock screws on it.

13
3. Installation of Water-proof Jacket (supplied)
It is recommended to adopt the water-proof jacket (supplied) for the network interface when the camera is installed
outdoor.
Steps:
e) If the network cable has been settled down, cut off the plug of the network cable first.
f) Route the network cable through the following components in sequence: fix nut, water-proof ring, and the main body
of the water-proof jacket, as shown in the figure.
g) Insert the water-proof ring into the main body of the water-proof jacket, to increase the sealing ability of the
components.
h) Wire the plug and network cables up.
i) Fix the O-ring to the network interface of the camera, and then connect the network cables.
j) Wrap the network interface with the main body of the water-proof jacket, and then rotate the fix nut clockwise to
assemble it to the main body of the water-proof jacket.
Network Interface O-ring Plug Water-proof Jacket Water-proof Ring Fix Nut Network Cable
Accessing via Web Browser
System Requirement:
Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz to Core i7-4000 series or higher, depending on different video resolutions
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above
version and Google Chrome8 and above version
To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same
subnet with your PC.
The following figure shows the cable connection of network camera and PC:
Steps:
1. Open the web browser.
2. In the browser address bar, input the IP address of the network camera, e.g., 192.0.0.64 and press the Enter key to
enter the login interface.
3. Input the user name and password.
4. Click Login.

14
5. Install the plug-in before viewing the live video and operating the camera. Please follow the installation prompts to
install the plug-in. You may have to close the web browser to finish the installation of the plug-in.

15
6. Reopen the web browser after the installation of the plug-in and login.
Notes:
The default IP address is 192.0.0.64.
The default user name is admin and password is wbox123.
This product has default user name and password credentials for first time access. You must change these
default credentials to protect against unauthorized access to the product.
For accessing the network camera from different subnets, please set the gateway for the network camera after you logged
in.
Live View
Log in the network camera to enter the live view page, or you can click Live View on the menu bar of the main page to
enter the live view page.
Descriptions of the live view page:

16
Camera Model:
It lists the camera model you are connecting to.
Online Help:
Click ‘Help’to get the online help, which will guide you through the basic operations for each function.
Menu Bar:
Click each tab to enter Live View, Playback, Log and Configuration page respectively.
Display Control:
Click each tab to adjust the layout and the stream type of the live view. And you can click the drop-down to select the
plug-in. For IE (internet explorer) user, webcomponents and quick time are selectable. And for Non-IE user,
webcomponents, quick time, VLC or MJPEG is selectable if they are supported by the web browser.
Live View Window:
Display the live video.
Toolbar:
Operations on the live view page, e.g., live view, capture, record, audio on/off, two-way audio, etc.
PTZ Control:
Panning, tilting and zooming actions of the camera and the light and wiper control. (only available for cameras supporting
PTZ function)
Preset/Patrol Settings:
Set/call/delete the presets or patrols for PTZ cameras. (only available for cameras supporting PTZ function)

17
Specifications
Model
WBXIL139RT
WBXIL209RT
WBXIL309RT
Camera
Image Sensor
1/3" Progressive Scan CMOS
1/2.8" Progressive Scan CMOS
1/3" Progressive Scan CMOS
Min. Illumination
0.01Lux @ (F1.2, AGC ON) ,0 Lux
with IR
0.01Lux @ (F1.2, AGC ON) ,0 Lux
with IR
0.028Lux @ (F2.0, AGC ON) ,0 Lux
with IR
0.07Lux @ (F1.2, AGC ON) ,0 Lux
with IR
Shutter Speed
1/3 s to 1/100,000 s
Lens
4mm@ F2.0
Angle of view: 73.1°
Angle of view: 85°
Angle of view: 79°(1920 × 1080)
Angle of view: 70°(2048 × 1536)
Day &Night
IR cut filter with auto switch
Digital Noise Reduction
3D DNR
Wide Dynamic Range
Digital WDR
Compression Standard
Video Compression
H.264/ MJPEG
Video Bit Rate
32 Kbps –8 Mbps
32 Kbps –12 Mbps
Image
Max. Resolution
1280 x 960
1920 × 1080
2048 × 1536
Frame Rate
30 fps (1280 × 960), 30 fps (1280 x
720), 30 fps (704 x 576),
30 fps (640 x 480)
30fps(1920 × 1080), 30fps (1280 ×
960), 30fps (1280 × 720)
20fps (2048 × 1536), 30fps (1920 ×
1080), 30fps (1280 × 720)
Image Settings
Rotate mode, Saturation, Brightness, Contrast adjustable by client software or web browser
Backlight compensation
Yes, zone optional
Network
Network Storage
NAS (Support NFS,SMB/CIFS)
Alarm Trigger
Motion detection, Dynamic analysis, Tampering alarm, Network disconnect , IP address conflict, Storage
exception
Protocols
TCP/IP,ICMP,HTTP,HTTPS,FTP,DHCP,DNS,DDNS,RTP,RTSP,RTCP,
PPPoE,NTP,UPnP,SMTP,SNMP,IGMP,802.1X,QoS,IPv6,Bonjour
General
One-key reset, Flash-prevention, dual stream, heartbeat, mirror, password protection, privacy mask, watermark,
IP address filtering, Anonymous access
Standard
ONVIF, PSIA, CGI, ISAPI
Interface
Communication Interface
1 RJ45 10M/100M Ethernet interface
Reset Button
Yes
General
Operating Conditions
-30 °C – 60 °C (-22 °F – 140 °F); Humidity 95% or less (non-condensing)
Power Supply
12 V DC ± 10%; PoE (802.3af)
Power Consumption
Max. 7 W
Ingress Protection level
IP66
IR Range
30 meters
Dimensions
60.4×76.9×139.28 mm (2.4” × 3.0” × 5.5”)
Weight
500g (1.1 lbs)

18
Model
WBXID134RT
WBXID204RT
WBXID304RT
Camera
Image Sensor
1/3" Progressive Scan CMOS
1/2.8" Progressive Scan CMOS
1/3" Progressive Scan CMOS
Min. Illumination
0.01Lux @ (F1.2, AGC ON) ,0 Lux
with IR
0.01Lux @ (F1.2, AGC ON) ,0 Lux
with IR
0.028Lux @ (F2.0, AGC ON) ,0 Lux
with IR
0.07Lux @ (F1.2, AGC ON) ,0 Lux
with IR
Shutter Speed
1/3 s to 1/100,000 s
Lens
2.8mm@ F2.0
Angle of view: 73.1°
Angle of view: 85°
Angle of view: 79°(1920 × 1080)
Angle of view: 70°(2048 × 1536)
Day &Night
IR cut filter with auto switch
Digital Noise Reduction
3D DNR
Wide Dynamic Range
Digital WDR
Angle Adjustment
Pan:0° - 355°, Tilt: 0° - 65°
Compression Standard
Video Compression
H.264/ MJPEG
Video Bit Rate
32 Kbps –8 Mbps
32 Kbps –12 Mbps
Image
Max. Resolution
1280 x 960
1920 × 1080
2048 × 1536
Frame Rate
30 fps (1280 × 960), 30 fps (1280 x
720), 30 fps (704 x 576),
30 fps (640 x 480)
30fps(1920 × 1080), 30fps (1280 ×
960), 30fps (1280 × 720)
20fps (2048 × 1536), 30fps (1920
× 1080), 30fps (1280 × 720)
Image Settings
Rotate mode, Saturation, Brightness, Contrast adjustable by client software or web browser
Backlight compensation
Yes, zone optional
Network
Network Storage
NAS (Support NFS,SMB/CIFS)
Alarm Trigger
Motion detection, Dynamic analysis, Tampering alarm, Network disconnect , IP address conflict, Storage
exception
Protocols
TCP/IP,ICMP,HTTP,HTTPS,FTP,DHCP,DNS,DDNS,RTP,RTSP,RTCP,
PPPoE,NTP,UPnP,SMTP,SNMP,IGMP,802.1X,QoS,IPv6,Bonjour
General
One-key reset, Flash-prevention, dual stream, heartbeat, mirror, password protection, privacy mask,
watermark, IP address filtering, Anonymous access
Standard
ONVIF, PSIA, CGI, ISAPI
Interface
Communication Interface
1 RJ45 10M/100M Ethernet interface
Reset Button
Yes
General
Operating Conditions
-30 °C – 60 °C (-22 °F – 140 °F); Humidity 95% or less (non-condensing)
Power Supply
12 V DC ± 10%; PoE (802.3af)
Power Consumption
Max. 7 W
Impact Protection
IEC60068-2-75Eh, 20J; EN50102, up to IK10
Ingress Protection level
IP66
IR Range
30 meters
Dimensions
Φ111 × 82 (4.4” × 3.2”)
Weight
500g (1.1 lbs)

19
Model
WBXIL136RT
WBXIL206RT
WBXIL306RT
Camera
Image Sensor
1/3" Progressive Scan CMOS
Min. Illumination
0.01Lux @ (F1.2, AGC ON) ,0 Lux with IR
0.028Lux @ (F2.0, AGC ON) ,0 Lux with IR
0.07Lux @ (F1.2, AGC ON) ,0 Lux with IR
Shutter Speed
1/3 s to 1/100,000 s
Lens
2.8 - 12 mm @ F1.4
Angle of view: 113°-33.8°
Angle of view: 105.2°-31.9°
Day &Night
IR cut filter with auto switch
Digital Noise Reduction
3D DNR
Wide Dynamic Range
Digital WDR
Compression Standard
Video Compression
H.264/ MJPEG
Video Bit Rate
32 Kbps –8 Mbps
32 Kbps –12 Mbps
Image
Max. Resolution
1920 × 1080
2048 × 1536
Frame Rate
30fps(1920 × 1080), 30fps (1280 × 960), 30fps (1280
× 720)
20fps (2048 × 1536), 30fps (1920 × 1080), 30fps
(1280 × 720)
Image Settings
Rotate mode, Saturation, Brightness, Contrast adjustable by client software or web browser
Backlight compensation
Yes, zone optional
Network
Network Storage
NAS (Support NFS,SMB/CIFS)
Alarm Trigger
Motion detection, Dynamic analysis, Tampering alarm, Network disconnect , IP address conflict, Storage
exception
Protocols
TCP/IP,ICMP,HTTP,HTTPS,FTP,DHCP,DNS,DDNS,RTP,RTSP,RTCP,
PPPoE,NTP,UPnP,SMTP,SNMP,IGMP,802.1X,QoS,IPv6,Bonjour
General
One-key reset, Flash-prevention, dual stream, heartbeat, mirror, password protection, privacy mask,
watermark, IP address filtering, Anonymous access
Standard
ONVIF, PSIA, CGI, ISAPI
Interface
Communication Interface
1 RJ45 10M/100M Ethernet interface
On-board storage
Built-in Micro SD/SDHC/SDXC card slot, up to 64 GB
General
Operating Conditions
-30 °C – 60 °C (-22 °F – 140 °F); Humidity 95% or less (non-condensing)
Power Supply
12 V DC ± 10%; PoE (802.3af)
Power Consumption
Max. 7.5 W
Ingress Protection level
IP66
IR Range
30 meters
Dimensions
95×105×258.6 mm (3.74” × 4.13” × 10.18”)
Weight
1200g (2.6 lbs)

20
Model
WBXID136VRT
WBXID206VRT
WBXID306VRT
Camera
Image Sensor
1/3" Progressive Scan CMOS
Min. Illumination
0.01Lux @ (F1.2, AGC ON) ,0 Lux
with IR
0.01Lux @ (F1.2, AGC ON) ,0 Lux
with IR
0.028Lux @ (F2.0, AGC ON) ,0 Lux
with IR
0.07Lux @ (F1.2, AGC ON) ,0 Lux
with IR
Shutter Speed
1/3 s to 1/100,000 s
Lens
2.8 - 12 mm @ F1.4
Angle of view: 98°-30.2°
Angle of view: 113°-33.8°
Angle of view: 105.2°-31.9°
Day &Night
IR cut filter with auto switch
Digital Noise Reduction
3D DNR
Angle Adjustment
Pan:0° - 355°, Tilt: 0° - 75°, Rotation: 0° - 355°
Wide Dynamic Range
Digital WDR
Compression Standard
Video Compression
H.264/ MJPEG
Video Bit Rate
32 Kbps –8 Mbps
32 Kbps –12 Mbps
Image
Max. Resolution
1280 x 960
1920 × 1080
2048 × 1536
Frame Rate
30 fps (1280 × 960), 30 fps (1280
x 720), 30 fps (704 x 576),
30 fps (640 x 480)
30fps(1920 × 1080), 30fps (1280
× 960), 30fps (1280 × 720)
20fps (2048 × 1536), 30fps (1920
× 1080), 30fps (1280 × 720)
Image Settings
Rotate mode, Saturation, Brightness, Contrast adjustable by client software or web browser
Backlight compensation
Yes, zone optional
Network
Network Storage
NAS (Support NFS,SMB/CIFS)
Alarm Trigger
Motion detection, Dynamic analysis, Tampering alarm, Network disconnect , IP address conflict, Storage
exception
Protocols
TCP/IP,ICMP,HTTP,HTTPS,FTP,DHCP,DNS,DDNS,RTP,RTSP,RTCP,
PPPoE,NTP,UPnP,SMTP,SNMP,IGMP,802.1X,QoS,IPv6,Bonjour
General
One-key reset, Flash-prevention, dual stream, heartbeat, mirror, password protection, privacy mask,
watermark, IP address filtering, Anonymous access
Standard
ONVIF, PSIA, CGI, ISAPI
Interface
Communication Interface
1 RJ45 10M/100M Ethernet interface
On-board storage
Built-in Micro SD/SDHC/SDXC card slot, up to 64 GB
General
Operating Conditions
-30 °C – 60 °C (-22 °F – 140 °F); Humidity 95% or less (non-condensing)
Power Supply
12 V DC ± 10%; PoE (802.3af)
Power Consumption
Max. 5.5 W
Impact Protection
IEC60068-2-75Eh, 20J; EN50102, up to IK10
Ingress Protection level
IP66
IR Range
30 meters
Dimensions
Φ140 × 99.9 mm (Φ 5.51” × 3.94”)
Weight
1000g (2.2 lbs)