Warming Trends PLATINUM IGNITION User manual
PLATINUM IGNITION
USER GUIDE
THANK YOU FOR YOUR PURCHASE!
Version 3.1
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
2
TABLE OF CONTENTS
Important Product Warnings .................................................................................................................................................3
Avertissements Importants Concernant les Produits .........................................................................................................4
General Information ...............................................................................................................................................................5
Code Requirements................................................................................................................................................................6
Minimum and Maximum Gas Inlet Pressures ......................................................................................................................6
Electrical Requirements .........................................................................................................................................................6
Control Box Layout.................................................................................................................................................................7
Platinum Installation Instructions ..........................................................................................................................................7
Warning Label ...................................................................................................................................................................... 16
Media Installation................................................................................................................................................................. 16
Operation Instructions ........................................................................................................................................................ 17
Lighting Instructions: Electronic Ignition Systems........................................................................................................... 17
General Maintenance.......................................................................................................................................................... 18
Troubleshooting................................................................................................................................................................... 19
Troubleshooting Countermeasures................................................................................................................................... 19
Warranty................................................................................................................................................................................ 20
Proposition 65 Warning ...................................................................................................................................................... 20
How to Order Replacement Parts ...................................................................................................................................... 21
Contact Us ............................................................................................................................................................................ 21
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
3
TABLE OF CONTENTS
Important Product Warnings .................................................................................................................................................3
Avertissements Importants Concernant les Produits .........................................................................................................4
General Information ...............................................................................................................................................................5
Code Requirements................................................................................................................................................................6
Minimum and Maximum Gas Inlet Pressures ......................................................................................................................6
Electrical Requirements .........................................................................................................................................................6
Control Box Layout.................................................................................................................................................................7
Platinum Installation Instructions ..........................................................................................................................................7
Warning Label ...................................................................................................................................................................... 16
Media Installation................................................................................................................................................................. 16
Operation Instructions ........................................................................................................................................................ 17
Lighting Instructions: Electronic Ignition Systems........................................................................................................... 17
General Maintenance.......................................................................................................................................................... 18
Troubleshooting................................................................................................................................................................... 19
Troubleshooting Countermeasures................................................................................................................................... 19
Warranty................................................................................................................................................................................ 20
Proposition 65 Warning ...................................................................................................................................................... 20
How to Order Replacement Parts ...................................................................................................................................... 21
Contact Us ............................................................................................................................................................................ 21
INSTALLER: Leave this user
guide with the appliance.
CONSUMER: Retain this
user guide for future
reference.
The installer is responsible for using the correct fuel
line sizing and/or regulation to provide gas within
the specied minimum and maximum gas inlet
pressures of the re feature.
DANGER
FIRE OR EXPLOSION HAZARD
If you smell gas:
• Shut off gas to the appliance.
• Extinguish any open ame.
• If odor continues, leave the area immediately.
• After leaving the area, call your gas supplier or re department.
• Failure to follow these instructions could result in re or explosion, which could cause
property damage, personal injury, or death.
WARNING
Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this
or any other appliances.
An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other
appliance.
WARNING: For Outdoor Use Only.
Installation and service must be performed by a qualied installer, service agency, or the
gas supplier.
WARNING
If the information in this is not followed exactly, a re or explosion may result causing
property damage, personal injury, or loss of life.
IMPORTANT PRODUCT WARNINGS
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no
odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a
camper, tent, car, or home.
DANGER!
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
4
INSTALLATEUR
Laissez ce manuel ave
l’appliance
CONSOMMATEUR:
Conserves ce manuel
pour référence ultérieure.
Il incombe à l’installateur d’utiliser le dimensionnement
et / ou la régulation corrects de la conduite de carburant
pour fournir du gaz dans les pressions d’entrée
minimum et maximum spéciées pour la fonction
incendie.
Ne pas utiliser cet appareil s’il a été plongé, même partiellement, dans l’eau. Appeler
un technicien qualié pour inspecter l’appareil et remplacer toute partie du système de
commande et toute commande qui a été plongée dans l’eau.
AVERTISSEMENT
Ne pas entreposer ni utiliser de l’essence ni d’autres vapeurs ou liquides inammables
dans le voisinage de l’appareil, ni de tout autre appareil.
Une bouteille de propane qui n’est pas raccordée en vue de son utilisation, ne doit pas
être entreposée dans le voisinage de cet appareil ou de tout autre appareil.
AVERTISSEMENT
Pour utilisation à l’extérieur seulement.
L’installation et l’entretien doivent être effectués par un installateur qualié, une agence
de service ou le fournisseur de gaz.
AVERTISSEMENT
Si les informations de ce manuel ne sont pas suivies à la lettre, un incendie ou une
explosion peut en résulter et causer des dommages matériels, des blessures corporelles,
ou la mort.
DANGER
RISQUE D’INCENDIE OU D’EXPLOSION
S’il y a une odeur de gaz :
• Coupez l’admission de gaz de l’arrareil.
• Éteindre toute amme nue.
• Si l’odeur persiste, éloignez-vous de l’appareil et appelez immédiatement le fournisseur
de gaz ou le service d’incendie.
• Si ces précautions ne sont pas respectées, cela pourrait provoquer un incendie ou une
explosion, pouvant causer des dommages matériels, des blessures ou la mort.
AVERTISSEMENTS IMPORTANTS CONCERNANT LES PRODUITS
DANGER! MONOXYDE DE CARBONE
Cette appareil peut produire du monoxyde de carbone,
un gaz inodore.
L’utilisation de cet appareil dans des espaces clos peut
entrainer la mort.
Ne jamais utiliser cet appareil dans un espace clos comme
un véhicule de camping, une tente, une automobile, ou
une maison.
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
5
GENERAL INFORMATION
WARNING
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
• Young children should be carefully supervised when they are in the area of the appliance.
• Clothing or other ammable materials should not be hung from the appliance or placed on or near
the appliance.
• Children and adults should be alerted to the hazards of high surface temperatures and should stay
away to avoid burns or clothing ignition.
WARNING
Do not use appliance if any part has been under water. Immediately call a qualied service technician
to inspect the appliance and to replace any part of the control system and any gas control that has been
under water.
WARNING
Product is not intended to be used to burn wood or other combustibles. Solid fuels shall not be
burned in the appliance.
WARNING
Only use Liquid Propane or Natural Gas as specied for your Warming Trends appliance or burner.
Do not use an alternative fuel.
the installer’s responsibility to read thoroughly before installing or servicing this equipment to ensure a safe
installation and to educate the end user as to proper operation. Warming Trends is not responsible for damage
due to improperly installed or operated units. Installers must leave this user guide with the end user. Instructions
website for applicable updates (www.Warming-Trends.com) Please keep this with your important papers.
This Owner’s Guide and User Guide contains critical information for the safe installation and operation of your
Platinum Ignition. You must read this user guide in its entirety prior to installation and/or operation. Failure to
follow these instructions may result in property damage, personal injury, or death.
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
6
CODE REQUIREMENTS
When the appliance is for connection to a xed piping system, the installation must conform with local
codes, or in the absence of local codes with the National Fuel Gas Code, ANSI Z223.1·NFPA54; National
Fuel Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, CSAB149.2,
as applicable.
MINIMUM AND MAXIMUM GAS INLET PRESSURES
GAS PRESSURE REQUIREMENTS
PRESSURE NATURAL GAS PROPANE
Minimum 3.5” W.C. / .8718 Kpa 8.0” W.C. / 1.9927 Kpa
Nominal 7.0” W.C. / 1.7436 Kpa 11.0” W.C. / 2.7399 Kpa
Maximum 14.0” W.C. / 3.4872 Kpa 14.0” W.C. / 3.4872 Kpa
It is the responsibility of the installer to consult with the local municipality and to FOLLOW ALL LOCAL CODES
For systems with Platinum Ignition:
ELECTRICAL CONNECTIONS
WIRING OF MULTIPLE PLATINUM IGNITIONS
yellow wires to the other wire from the transformer.
Note: When connecting two units, it is essential to use a higher output transformer.
WARNING
Platinum Ignition System operates on 24 Volts AC power ONLY
DO NOT Attempt to Power using 110 Volts AC Power - Damage WILL RESULT
ELECTRICAL REQUIREMENTS
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
7
PLATINUM INSTALLATION INSTRUCTIONS
INSTALLATION OF THE PLATINUM IGNITION PILOT ASSEMBLY TO THE PLATE USING PRE-CUT KNOCKOUTS
The Plate or Pan that was included with your burner should have pre-cut pilot assembly knockouts for various
burners. The burner type and size are etched into the plate/pan next to the knockout for that burner’s pilot
assembly location. To install the pilot assembly:
Photo 1: Pilot Assembly Knockouts Photo 2: Breaking the Knockouts
1. LOCATE AND REMOVE THE APPROPRIATE KNOCKOUT
1.1
1.2 Locate the Pilot Assembly knockout on the plate/pan that matches your burner type and size.
{See Photo 1}
1.3 Remove the matching knockout by placing a screwdriver or other small tool in the opening at the edge
of the knockout. Push one side of the knockout down to break the connector and remove the circular
piece of aluminum with pliers. Do not remove any other knockouts. {See Photo 2}
Gas Outlet
Power
Pilot Gas Output
Diagnostics
Hot Surface Igniter
Thermopile
LED Light
CONTROL BOX LAYOUT
(Internal Use Only)
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
8
2.2 Remove the wind cage cap from the top of the pilot assembly and set it aside until the plate/pan is
2.3
opening created in step 1.3.
2.4 Rotate the pilot assembly in the knockout opening until the circular opening on the wind cage and
thermopile are adjacent to the nearest jet with the thermopile nearest to the jet. Position the pilot
assembly to cover the entire knockout opening. {See Photo 4a and 4b}
Photo 4a: Wind Cage Positioning Photo 4b: Wind Cage Circular Opening Positioning
Photo 3a: Pilot Assembly Photo 3b: Top-Down View of Pilot Assembly
2. INSTALLING THE PILOT ASSEMBLY ON THE PLATE/PAN
2.1
{See Photo 3a and 3b}
Wind Cage
Wind Cage Cap
Self Tapping Screws
Pilot Burner Thermopile
Hot Surface Igniter
HSI
Thermopile
Pilot Tube
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
9
Photo 6: Drip Legs Photo 7: Installing the Drip Leg
2.5
or pan. {See Photo 5)
3. INSTALLING THE VALVE INTO THE PLATE/PAN
Warming Trends has two different drip legs for the Platinum Ignition System depending on the BTU supply of
{See Photo 6} The
second drip leg is for burners with 300K BTUs or more and is made out of ¾’’ piping.
3.1
assembly and tighten to the female end of the coupling with a wrench to avoid leaks. Align the tee so it is
facing away and perpendicular to the two small holes cut out on the plate. {See Photo 7}
Photo 8a: Valve Box for Units Under 299K BTUs Photo 8b: Valve Box for Units Over 300K BTUs
3.2
¾’’ Reducing Bushing attached for units under 299K BTUs {See Photo 8a} or a ¾’’ x 3’’ nipple attached for
units over 300K BTUs {See Photo 8b}
Photo 5: Securing the Wind Cage to the Plate/Pan
1/2” Drip Leg 3/4” Drip Leg
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
10
Photo 9: Attaching the Valve Box to the Drip Leg
3.3
on the valve and tighten to the female end of the tee on the drip leg. Tighten with a wrench to avoid leaks.
{See Photo 9} Orient the valve so that the connectors on it face away from the plate. {See Photo 10}
Photo 10: Orienting the Valve
4. CONNECTING THE PILOT TO THE VALVE ASSEMBLY
4.1 Identify the connectors ports on the valve. One is black and labeled Hot Surface Igniter and one is gray
and labeled Thermopile. Locate the connectors of the same color on the pilot assembly and plug them in
to the matching connectors.
{See Photo 11}
4.2
Identify the brass male thread on the valve. Locate the corresponding brass female thread on the metal pilot
tube extending from the wind cage. Join the female end on the pilot assembly to the male end on the valve using
(DO NOT APPLY ANY THREAD SEALANT). {See Photo 12}
Photo 11: Electronic Connections from the Pilot to Valve Photo 12: Connecting the Gas Line From the Pilot to the Valve
Photo 13: Mounting the Transformer to the Plate
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
11
Photo 10: Orienting the Valve
5. CONNECTING THE TRANSFORMER TO THE VALVE ASSEMBLY
5.1 Identify the transformer unit attached to an aluminum mounting bracket. The transformer unit also comes
on the bracket up with the holes on the plate and fasten the two together with the screws provided. Ensure
the transformer unit is facing away from the center of the plate. {See Photo 13}
5.2 Locate the two Phillips head screws on the transformer box that hold the panel in place. Unfasten these
screws and remove the panel. {See Photo 14}
5.3
out of it to connect to the power supply and the other is empty. {See Photo 15} Loosen the empty strain
relief and remove the cap.
Photo 14: Removing the Front Panel
Photo 13: Mounting the Transformer to the Plate
Photo 15: Loosening the Knob
Strain Relief
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
12
Photo 16a: Feeding the Valve Wires into the Transformer Box Photo 16b: Reconnecting the Knob
Photo 17: Connecting the Valve to the Transformer
5.4
through the uncapped strain relief on the transformer unit and tighten the strain relief back down around the
wires. {See Photos 16a and 16b}
5.5
corresponding blue and yellow wires that were fed from the valve into the unit. {See Photo 17}
5.6
6. ASSEMBLY FLEX LINE KITS FOR IGNITION
6.1 {See Photo 18}
Photo 18: FK1
Photo 19: Flared Fitting with Thread Sealant
Flared Fitting
½” x 2” Nipple
Escutcheon Plate
Flex Line
¾” Key Valve
3” Key
12” Key
Thread Sealant
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
13
6.2
{See Photo 19} and screw into the “IN”
side of the valve. Tighten with a wrench to avoid leaks. {See Photo 20}
6.3
Tighten with a wrench to avoid leaks. {See Photo 21}
6.4
valve using thread sealant. Tighten with a wrench to avoid leaks. {See Photo 22}
6.5
thread sealant. Tighten with a wrench to avoid leaks. {See Photo 23} The other end of the key valve will then connect
to your gas supply.
Photo 19: Flared Fitting with Thread Sealant Photo 20: Connecting the Flared Fitting to the Platinum Valve
Photo 21: Attaching the Flex Line
Photo 22: Connecting the Flared Fitting to the Key Valve
Photo 23: Connecting the Flex Line from the Platinum Valve to the Key Valve
Flared End (No thread sealant)
Non-Flared End
Thread Sealant
Gas Supply
Fire Pit
Flex Line leading to the
Platinum Valve
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
14
FK2 Installation:
6.6 Identify your FK2 for 300K BTU and above units. {See Photo 24}
6.7 Identify one of the ¾” x 3” nipples that comes with your kit. Apply thread sealant to one end of the nipple
and screw into the “IN” side of the valve. Tighten leaks {See Photo 25}
6.8
tee. Use thread sealant for all connections and tighten all connections with a wrench to avoid leaks. {See
Photo 26} for complete installation.
Photo 24: FK2
Photo 25: Connecting the ¾” x 3” nipple to the Platinum Valve
Photo 26: Connecting the Flared Fittings and ¾” Tee to the 3” Nipple
Flex Line
Flared Fitting 3” Key
12” Key
¾” Key Valve
¾” x ½” Adapter
Escutcheon Plate
¾” Tee
¾” x 3” Nipple
Flared End (No thread sealant)
Tapered End (Apply thread sealant)
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
15
6.9
Photo 26. Do not use thread sealant. Tighten with a wrench to avoid leaks. {See Photo 27}
6.10
{See
Photo 28}
6.11
attached to your key valve assembly. This will connect the Key Valve to the Platinum Valve {See Photo 29}.
The other end of the key valve will then connect to your gas supply. Do not use thread sealant. Tighten
with a wrench to avoid leaks.
7. FINISHING UP
7.1
cap back on the wind cage. This must be done before any media is added to the feature to prevent any
pieces from falling into the wind cage. Make sure the power to the feature is turned off. Plug the 6’ pigtail
into the GFCI outlet. Turn the power on to ignite.
Photo 27: Connecting the Flex Lines to the Flared Fittings
Photo 28: Constructing the Key Valve assembly that will connect to the Platinum Valve
Photo 28: Connecting the Flex Lines from the Platinum Valve to the Key Valve
Fire Pit
Flex Lines leading to the Platinum Valve
Gas Supply
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
16
To avoid media dust or debris from getting into the system, do not dump the
media over the burner. Place the media onto the plate or pan.
burner ignition. (See pictures below for examples of proper installation heights.)
to the pilot assembly may cause excessive heat on pilot causing system to fail. Not covered under warranty.
MEDIA INSTALLATION
Examples of proper media
height on pilot assembly.
Pilot Cooling Holes
WARNING:
owner’s user guide provided with this
appliance. Installation and service must be
WARNING: Do not store or use gasoline or
vicinity of this or any other appliances.
An LP-cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
AVERTISSEMENT:
une réparation ou un entretien
inapproprié peuvent être la cause de
blessures ou de dommages. Veuillez
lire attentivement les instructions
avant d’installer ou de réparer ce
matériel.
AVERTISSEMENT: Ne pas entreposer ni
utiliser de l’essence ni d’autres vapeurs
appareil.
Un bouteille de propane qui n’est pas
ne doit pas être entreposée dans le
voisinage de cet appareil ou de tout
autre appareil.
the appliance.
WARNING LABEL
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
17
TURNING ON YOUR ELECTRONIC IGNITION SYSTEMS
1.
feature.
2. Any cover must be removed prior to operation of burner and must remain off during operation.
Danger: Fire or Explosion Hazard. If you smell gas, shut off gas to the appliance, extinguish any open
ame. If odor continues, leave the area immediately. After leaving the area, call your gas supplier or re
department. Failure to follow these instructions could result in re or explosion, which could cause property
damage, personal injury, or death.
3.
4.
5.
6.
WARNING:
outlet should be installed within the interior of the enclosure above grade to supply power to system.
TURNING OFF YOUR ELECTRONIC IGNITION SYSTEMS
1.
2. Turn key valve to OFF position by turning key to the right.
3.
4.
5.
WARNING:
WARNING: Do NOT use this appliance if any part has been under water.
system and any gas control which has been under water.
WARNING: HOT - DO NOT TOUCH - SEVERE BURNS MAY RESULT - CLOTHING IGNITION MAY RESULT
CAREFULLY SUPERVISE children in same area as the appliance. Alert children and adults to hazards of high
near the appliance.
WARNING
guard or protective device removed for servicing must be replaced prior to operation. Keep the appliance
OPERATION INSTRUCTIONS
WARNING
gas shutoff.
LIGHTING INSTRUCTIONS: ELECTRONIC IGNITION SYSTEMS
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
18
GENERAL MAINTENANCE
PRIOR TO EACH USE
SEMI ANNUALLY
thermocouple of any soot using soft brush. Be careful not to damage the igniter element. Be sure when returning
your media to the feature to avoid over covering the jets and the pilot assembly as mentioned on page 8.
ANNUALLY
paper clip.
WARNING
Fire feature should be inspected by user prior to each use and inspected at least once annually by a
WARNING
WARNING
Ensure gas and power are shut off and appliance is cool before servicing.
WARNING
Any guard or protective device removed for servicing must be replaced prior to operating
the appliance.
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
19
Below are some potential causes and countermeasures to the symptoms.
NO PILOT FLAME. HSI HEATS UP BUT PILOT WON’T LIGHT
• Air in the gas line - If this is a new install, it may take several attempts to purge the air.
• Debris is in the gas line - Clear the gas line.
• Water/Moisture is in the gas line - Clear the gas line.
• Incorrect Gas pressure - Conrm proper gas pressure.
• Pilot gas orice is dirty - Remove the pilot head and clean.
• Wind conditions might be too severe.
PILOT LIGHTS BUT BURNER WILL NOT LIGHT
• Gas pressure is incorrect - Conrm proper gas pressure.
• Small pilot ame - Remove the pilot head and clean pilot gas orice.
• Dirty thermal sensor - Clean using soft brush.
• Debris is blocking gas orice in burner - Purge water and air from gas lines or in the burner, and conrm
there is no debris in gas lines.
BURNER TURNING OFF UNEXPECTEDLY
• Improperly applied media - Make sure your media is not covering the pilot assembly and that your logs
are not placed over or too near the wind cage.
• Gas pressure is incorrect - Conrm proper gas pressure by checking at the gas stub to the feature and
the Gas Inlet Pressure.
• Wind conditions – Conrm the burner is properly located 4 - 6” inside the feature, and be sure the wind
conditions are not too severe for safe use.
FIRE FEATURE IS MAKING A WHISTLING SOUND
• Flex line issue - Conrm the correct size ex line is installed and there are no kinks or tight bends in the
line.
• Gas pressure is incorrect - If the whistling is coming from the jets, conrm the gas pressure is within the
ranges recommended on the Gas Pressure Inlet chart provided on page 6. Adjust as needed.
Please contact your retailer or certied technician for service and repair if these suggestions do not solve the
issue. If replacement parts are required – contact your retailer or licensed technician for authorized replacement
parts. Warranty is null and void if unauthorized parts are used.
TROUBLESHOOTING
TROUBLESHOOTING COUNTERMEASURES
NUMBER OF FLASHES ERROR REASON
Solid LED
LED Off
1
2 Thermopile issue detected - Thermopile did not detect heating or did not get hot/
3 24 hour timer trigger - Pit has been on for more than the maximum allowed time.
Power cycle is required.
4
and OFF for 0.5 seconds.
Warming-Trends.com | 303 346 2224 | Orders@Warming-Trends.com
20
ALL BURNERS AND ELECTRONICS MUST BE COVERED WHEN NOT IN USE OR WARRANTY IS NULL AND VOID
For all Platinum Ignition Systems, problems or defects in the functioning of the systems due to gas plumbing or electrical
installed by others are not covered by any warranty offered by Warming Trends. No dealer, distributor, or other person has the
authority to represent or warrant a Warming Trends product beyond the terms contained within this warranty, and Warming
Trends assumes no liability for such warranty representations. Any questions concerning this warranty should be directed to
the Warming Trends corporate ofce or via email: legal@Warming-Trends.com.
necessary third-parties in order to do so.
YOUR RIGHTS UNDER STATE LAW
articles/0252-warranties
PLATINUM IGNITION SYSTEM WARRANTY
WHAT IS “PROP 65”?
Californians to make informed decisions about their exposures to these chemicals.
of drinking water.
published in 1987.
p65warnings.ca.gov For a fully updated list of all the chemicals and compounds that are known to the State of California to
WARNINGS
p65warnings.ca.gov
various fuels. View the fact sheet at www.p65warnings.ca.gov
female reproductive system. View the fact sheet at www.p65warnings.ca.gov
Furniture Product Exposure: Some furniture products can expose you to chemicals which are known to the State of California
to cause cancer or birth defects or other reproductive harm. View the fact sheet at www.p65warnings.ca.gov
Want to see more? View all of the Prop 65 fact sheets at www.p65warnings.ca.gov
MORE INFO ON PROP 65
prop65.
Note: The information provided is for informational purposes only and does not constitute legal advice. If you have any
PROP 65 WARNING
Table of contents
Other Warming Trends Burner manuals
Popular Burner manuals by other brands
artisan
artisan Art-SB1 Care & use manual
Riello
Riello RS 64/M MZ Installation, use and maintenance instructions
Riello
Riello DB 4 SE FGR Installation, use and maintenance instructions
Riello
Riello RS 68/E O2 ULX Installation, use and maintenance instructions
Monessen Hearth
Monessen Hearth Natural Blaze Series Installation & owner's manual
Power Flame
Power Flame HAC3-GO2 Installation and operation manual
Riello
Riello RS 160/M BLU instruction manual
Enertech
Enertech Bentone B1FUV Classic Installation and maintenance instruction
Riello
Riello 40 Bio G5 Installation, use and maintenance instructions
Campingaz
Campingaz BLEUET G 206 Instructions for use
Oilon
Oilon GP-600 M Operation and maintenance manual
Riello
Riello COH 180 Installation, use and maintenance instructions
baltur
baltur BT 75 DSPG Manual user instructions
Lamborghini Caloreclima
Lamborghini Caloreclima LMB LO 300 2ST Instructions for installation, use and maintenance manual
Riello
Riello RL 28/2 Installation, use and maintenance instructions
Riello Burners
Riello Burners Gulliver BLU Series Installation, use and maintenance instructions
Riello
Riello 464T52 Installation, use and maintenance instructions
Beckett
Beckett AF instruction manual