Waterhouse XC-SP08301 User manual

12 Volt Macerator Pump User Guide Manual
Model: XC-SP08301 MACERATOR PUMP
Waterhouse Macerator Pump Works well for fish box, live well and holding tank
applications. This Pump is equipped with all copper motor, so that it will not shock when it is
overloaded. It is all wrapped in copper wire to ensure its long lasting. The quality of the
motor will determine the lift time of the pump.
•Pump Head 2 Chambers
•Open flow 49.2L/min(13GPM)
•No Pressure
•2-pin connector with on/off switch
•inlet/outlet size 2"(50mm)/1"(25mm)
•12V 24V Motor optional Specification
Product Details
Waterhouse Macerator Pump
Works well for fish box, live well and holding tank applications. This Pump is equipped with all
copper motor, so that it will not shock when it is overloaded. It is all wrapped in copper wire to
ensure its long lasting. The quality of the motor will determine the lift time of the pump.
1.Pump Head 2 Chambers
2.Open flow 49.2L/min(13GPM)
3.No Pressure
4.2-pin connector with on/off switch
5.inlet/outlet size 2"(50mm)/1"(25mm)
6.12V24V Motor optional
Specification
10/5amp power draw
49.2 litres per minute maximum flow
2.3Kg weight
515mm x420115mm x32mm dimensions

10/5amp power draw
49.2 litres per minute maximum flow
2.3Kg weight
515mm x 420115mm x32mm dimensions
Caution:
Please read all instructions carefully before installing this product.
This pump is not ip68 sealed and therefore shall by any means never be submerged.
However, the electric wire connections must not be submerged. For extra protection please
insulate all joints and ends with approved insulation or shrink tapes to avoid electric shocks
and fire sparks that may cause explosions or fires.
Security:
•12V diaphragm pumps can only be used for pumping clean water and non-corrosive
chemicals and liquids.
•Please connect pump’s black and white wire to the negative terminal (-) and white
wire to the positive terminal (+).
•Make sure you use suitable size fuses.
•The wire connections must be insulated by shrink or watertight insulation tape.
•All wire connections must be outside water, unless necessary provided you have an
ip68 waterproof connector.
•Please do not run the pump dry.
•Your pump must always be protected from water splashes or any liquid chemicals.
•Make sure the pump works in a ventilated environment.
Specifications:
•Impeller structure: Open impeller, Impeller inhalation: Single suction, Number of impeller
:6, Drainage outlet diameter: 28mm, Drainage inlet diameter:48mm, Flow rate: 47L/min,
Maximum lift: 3m, Voltage:12v, Current:14A/7A.
•Applicable scope: rv, yacht, toilet, sewage, industry, sea.
•With double blade design, impurities in sewage can be easily discharged.
•Reinforced base, wear resistance, not easily deformed, rusty.
•Convenient installation, stable performance, high efficiency, and energy saving.
Model
Flow Rate
Volt
Current (A)
Head (m)
Cable
Outlet Dia
Weight
XC-
SP08301
47L/MIN
12
14AMP
20
30cm
25mm
1.5kgs

Warning:
•To prevent injury, always disconnect the power source when installing or servicing
any electric product.
•Do not use the pump-to-pump gasoline oil or any flammable liquids.
•Always make sure you use fuse amperage rated for your pump model.
•Failure to follow these instructions may result in serious injury or fire hazards.
Optional Materials:
•Mounting screws
•Waterproof adhesive (epoxy, silicone, or fibre glass adhesive) to mount the block.

Pump Mounting Instructions:
Warning: remove any polystyrene or foam blocks covering the pump around for
shipping purposes.
•Step 1: make sure you mount the pump facing down or aside on its feet make sure it
is holding firmly as to avoid too much vibration that will affect your seals and
bearings.
•Step 2: now insert your hose inlet/outlet and use hose clamps to secure the pipes.as
is the pump has high pressure it’s advisable to use hose pipes or high-pressure flexi
hoses.
•Step 3: now you can link your inlet pipe to the water source and outlet to the supply,
you must always watch for the inlet/outlet arrow when installing this type of pump.
•Step 4: make sure your pump is not more than 2m high or away from water source
when self-priming.
•Step 5: make sure you pump is covered or protected from water or rains never
submerge the pump.
•You can adjust your pressure by opening the front cover screw on the pressure
switch, inside there is another screw by turning it clockwise you can adjust the
start and stop pressure.
Pump mounting:

Operation:
1. Connect your -+ terminals accordingly to your battery positive and negative poles.
2. Make sure you have right size fuse on your positive pole.
3. Connect your pump to the control switch, depending on what operation you are
using the pump for:
•Use a float switch for draining or filling.
•Use pressure switch for water pressure boosting.
•Or manual start stop switch for water circulation etc.
Care & Maintenance:
•Always watch your power supply voltage or current for over voltage, under voltage
or short circuit.
•Make sure your pump filter sieve is always clean of debris or any clogging dirty.
•Careful attention will guarantee outstanding pump performance.
Parts:
thth

For more information, please feel free to contact us on
011 466 8520 or email us at [email protected]a