WB Mfg Viola User manual
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
1
Assembly Instructions
Viola/Violin Rack
Tools Required
• 4mm Allen
Wrench OR
• 4mm hex bit
• Phillips screw
driver
• Screw gun
• Square screw
driver
Step 1:
• On a protected flat surface and with the help of another person, align the threaded inserts of the (lower) rails to the (lower) brace.
• Using a ⁄”-20x1⁄” joint connector bolt, insert the bolt going through the pre-drilled hole in the rail to the threaded insert of the brace. Use a 4mm Allen
wrench or 4mm hex bit and a screw gun to fasten the bolt into place. Repeat for the remaining (3) bolts.
• After the first rail is attached to the brace, repeat for the remaining rail on the other side of the brace.
• Repeat this step with (upper) rails and (upper) braces.
NOTE: Colored images are for illustrative purposes only. V072121 Version subject to change
(Upper)
(Lower)
Rails w/ Armor
Edge (shown in
pink)
Braces (shown in
green)
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
2
Step 2:
• With the help of another person, align the threaded inserts in the (lower) rail assembly with the pre-drilled holes in (right) side panel.
• Using a ⁄”-20x1⁄” joint connector bolt, insert bolt going through the hole in the side panel to the threaded insert. Use a 4mm Allen wrench or
4mm hex bit and a screw gun to fasten the bolt into place. Repeat for the remaining (3) bolts.
• After the rail assembly is attached to the (right) side panel, repeat for (left) side panel.
• Repeat this step for the (upper) rail assembly.
Side panels
(shown in yellow)
(Right)
(Left)
Rails w/ Armor
Edge (shown in
pink)
(Lower)
(Upper)
NOTE: Parts shown in grey are assembled in previous steps.
NOTE: Colored images are for illustrative purposes only.
Red dots show the location
where the joint connector
bolts are to be used in this
step.
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
3
Assembly Instructions
Viola/Violin Rack
Support rail
(upper, shown in
purple)
Support rail
(lower, shown in
blue)
(Right)
(Left)
Step 3:
• Align the threaded inserts in the (lower) support rail with the pre-drilled holes in the (right) side panel. Using a ⁄”-20x1⁄” joint connector bolt, insert the
bolt going through the pre-drilled hole to the threaded insert. Use a 4mm Allen wrench or 4mm hex bit and a screw gun to fasten the bolt into place.
• Repeat for the remaining (3) bolts.
• After the (lower) support rail is attached to the (right) side panel, repeat for (left) side panel.
• Repeat this step for the (upper) support rail using (3) bolts per end.
NOTE: Parts shown in grey are assembled in previous steps.
NOTE: Colored images are for illustrative purposes only.
Red dots show the location
where the joint connector
bolts are to be used in this
step.
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
4
Neck holders
(shown in red)
Side panels
(shown in yellow)
(Right)
(Left)
Support rail
(upper, shown in
purple)
Step 4:
• Align the threaded insert in the (lower) neck holder with the pre-drilled hole in the (lower) support rail..Using a ⁄”-20x1⁄” joint connector bolt, insert
the bolt going through the pre-drilled hole to the threaded insert. Use a 4mm Allen wrench or 4mm hex bit and a screw gun to fasten the bolt into place.
Repeat for the remaining bolts.
• Repeat this step for the (upper) neck holder and (upper) support rail.
Step 5:
• Align the threaded insert in the (lower) neck holder with the pre-drilled hole in the (right) side panel. Using a ⁄”-20x1⁄” joint connector bolt, insert the
bolt going through the pre-drilled hole to the threaded insert. Use a 4mm Allen wrench or 4mm hex bit and a screw gun to fasten the bolt into place.
• After the (lower) neck holder is attached to the (right) side panel, repeat for (left) side panel.
• Repeat this step for the (upper) neck holder.
NOTE: Parts shown in grey are assembled in previous steps.
NOTE: Colored images are for illustrative purposes only.
Assembly Instructions
Viola/Violin Rack
Support rail
(lower, shown in
blue)
Red dots show the location
where the joint connector
bolts are to be used in this
step.
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
5
(SIDE VIEW)
Step 6:
• With the help of another person, place the rack on it’s back on a protected flat surface.
• Attach the reinforcement bracket to the side panel by using a ⁄”-20x20mm joint connector bolt going through pre-drilled hole in the bracket and the
side panel and making sure bolt is pushed as far as it can go. While holding the joint connector bolt flush to the side panel, take a ⁄”-20 joint connector
nut and attach it to the end of the bolt turing it clockwise until it’s completely on. Use a 4mm Allen wrench or 4mm hex bit and a screw gun to tighten as
needed. Repeat for the second bolt and nut.
• Repeat with the remaining (3) reinforcement brackets.
Step 7:
• Attach the 3” wheel caster by threading the stem of the locking caster into the reinforcement bracket making sure it’s threaded all the way.
• Repeat for the remaining locking casters.
• NOTE: Casters are NOT to be used as a leveling device.
• With the help of another person, place the rack in its’ upright position.
Assembly Instructions
Viola/Violin Rack
Reinforcement
bracket (shown
in red)
CUSTOMER REF. NO.
0400993
SHEET 1 OF 1
EMB
DWG. NO.
TITLE:
REV
SQUARE FOOT
Phone: 715-669-5360; Fax: 715-669-5929
ANGULAR:
3" wheel, 4" load height, 3" swivel rad.,
written permission of WISCONSIN BENCH
CUST. No.CUSTOMER NAME:
FILE LOCATION:
REF. NO.
xx-xx-xx
thereon to others without the expressed
NONE
SCALE:
reserves the right to change specifications,
disclose this drawing or any information
copy, distribute, reproduce, transmit or
and proprietary. WISCONSIN BENCH
in WISCONSIN BENCH. Holder may not
rights, title, and interest therein reside entirely
BENCH and are to be treated as confidential
unless the drawing is marked certified. All
1 °
DRAWN BY
REVISION DESCRIPTION BY DATE
DRAWN DATE
1.25" tread width, w/brake
PT
This drawing and the information contained
herein are the property of WISCONSIN
TOLERANCES:
2 PLC. DEC. .06
3 PLC. DEC. .031
507 E. Grant St., Thorp, WI 54771
3” wheel
caster
Step 7
NOTE: Colored images are for illustrative purposes only.
Step 6
Red dots show the location
where the joint connector
bolts are to be used in this
step.
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
6
Part Identifier Key
Description Qty.
Side panel 2
Rail w/ Armor
Edge 4
Brace Varies
Support rail
(lower) 1
Support rail
(upper) 1
Neck holder 2
NOTE: Colored images are for illustrative purposes only.
Part # Qty. Description
0406517 Varies ⁄”-20x1⁄” joint connector
bolt
0400861 4 14g reinforcement bracket
0404229 8 ⁄”-20x17mm joint connector
nut
0404228 8 ⁄”-20x20mm joint
connector bolt w/ loctite
0400993 4 3” wheel caster w/ brake
Assembly Instructions
Viola/Violin Rack
This manual suits for next models
1
