WDR M062-VDW101-003 User manual
Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow
these instructions.
WDR
HIGH RESOLUTION
VANDAL DOME CAMERA
OPERATION MANUAL
M062-VDW101-003
CONTENTS
1. Cautions
2. Features
3. Equipment and Accessories
4. Overview and function
5. Installation
6. Connection
7. Dimensions
8. Specifications
9. OSD Menu
•MENU DESCRIPTION
•GENERAL STRUCTURE
•OSD FUNCTION DESCRIPTION
•FACTORY DEFAULT
•EXIT
10.Communication Protocol
2
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note - This equipment has been tested and found to comply with limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio / tv technician for help.
Caution - Any changes or modications in construction of this device which are not
expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
1. A regulated DC12V 1.5A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal
components. Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
1.Cautions
3
1.Cautions
4
WEEE
(Waste Electrical & Electronic Equipment)
This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this product, or
their local government ofce, for details of where and how they can take item
for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
This symbol is intended to alert the user to the presence
of un-insulated “dangerous voltage” within the product’s
enclosure that may be of sufcient magnitude to constitute a
risk of electric shock.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
• Sony Vertical double-density interline CCD image sensor
• 550TV Lines
• WDR (Wide Dynamic Range), OSD Function
• Digital slow shutter, Manual shutter
• Privacy Zone
• Motion Detection
• IR LED : 30ea, Max 30M
• Manual Pan & Tilt Control for easy installation
- Horizontal 360˚, Pan 360˚, Tilt 140˚
Minute Angle Control ±10˚
• Vandalproof
OPTION
• AC24V / DC12V Dual Voltage
• Fan(standard type)
How WDR makes better image?
WDR allows every detail to be captured accurately even if one
portion is bright while other portions are dark.
(The difference of two portions could be more than 64 time)
2.Features
5
• 3-Axis Gimbal
The Service Video Connector also provides the installer with an
easy way of configuring the camera.
• Service Video connector
Pan Rotation Horizontal RotationTilt Rotation
CAUTION panning the bracket in excess of 3 rotations in one direction may
cause damage to the cable.
2.Features
6
1 VANDAL DOME CAMERA
2SURFACE MOUNT
3VIDEO OUTPUT TEST CABLE
4OPERATION MANUAL
5
SCREW(M4x10) - 4ea
SCREW(5x30) - 4ea
SCREW(M4x40.SUS) - 4ea
L WRENCH - T20
6MOUNT GUIDE
3. Equipment and Accessories
7
• Name (Led Type)
• Name (Standard)
4.Overview and function
8
OSD Joystick
OSD Joystick
• CONTROL FUNCTION
(OSD JOYSTICK)
LEFT
UP
RIGHT
DOWN
Standard TypeLED Type
Mount Guide
5. Installation
9
Lens Zoom Knob
Lens Focus Knob
Separate LED Cover (Sunshield Cover)
and adjust LENS ZOOM / FOCUS KNOB
After setting the LENS, assemble the
LED Cover (Sunshield Cover).
1. Installation of Flush Mount
2. Installation of Surface Mount
PIPE
PIPE
① Installation of the camera with SURFACE
CASE(using M4x40)
② Installation of the camera with SCREWS
③ Installation of the camera with JUNCTION BOX
① Installation of the camera on the wall
② Installation of the camera on the 3/4” NPT PIPE
③ Installation of the camera on the JUNCTION BOX
Check the safe wire which
should be entirely inserted into camera
housing during locking the dome cover to
maintain Weatherproof condition.
When using the camera
without LEDs take off the rubber.
NOTE
5. Installation
10
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
• DUAL(DC12V/AC24V)
• DC12V
6.Connection
11
DC12V / AC24V
Regulated power supply
DC12V
Regulated power supply
Video in
Video in
BNC Female Video
BNC Female Video
Unit : mm
70
˚70
˚
Standard Type LED Type
When you x the focus around 22.0mm in f9.0-22.0mm Varifocal lens, please
set short distance focus approximately 3M and do not set long distance focus.
Surface Mount Type
Flush Mount Type
Type A Type B
7.Dimensions
12
Signal Format NTSC PAL
Image Device Sony Vertical double-density interline CCD image sensor
Scanning System 2:1 Interlace
H.Resolution 550TV Lines
Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Electronic Shutter 1/60 sec 1/50 sec
Digital Slow Shutter 1 ~ 500 Field
WDR Off / On / AUTO(Level Adjustment)
BLC Off / Bottom / Left / Right / Top / Center
AGC LOW / MID / HIGH
Motion Detection Zone(Whole, Top, Bottom, Center, Left, Right) / Level Adjustable
Privacy Masking Zone 8ea (Mask Off / On)
White Balance ATW / PUSH / PUSH LOOK / USER(R Gain, B Gain)
OSD Built-In
Language English / Chinese / Russian / Spanish / German
S/N Ratio More than 48dB(AGC Off)
Gamma r=0.45
Min. Illumination 1.0 Lux / 30 IRE F2.0
0.001 Lux(DSS)
Sync System Internal
Video Output 1.0 Vp-p Composite 75(Ω) unbalanced
Power
Consumption
DC12V DC 12V ±10%, Less than 210mA
Dual • DC 12V ±10%, Less than 300mA
• AC 24V ±10%, Less than 3.1W
Operating Temperature -10℃~ +50℃
Storage Temperature -20℃~ +60℃
Operating Humidity 10% ~ 80%
Options Dual Power
Weight • Surface Mount Type A : Approx. 1.38kg / Type B : Approx. 1.1kg
• Flush type : Approx. 730g
IP Rating IP 66 (Weatherproof)
Power
Consumption
DC12V DC 12V ±10%, Less than 550 mA
Dual • DC 12V ±10%, Less than 700 mA
• AC 24V ±10%, Less than 6.8W
Min. Illumination 0 Lux (IR LED ON)
IR LED 30ea
IR LED Half Angle ±22 Degree
IR LED Wavelength 850nm
IR Beam Range Up to 30 Meters
IR LED Operation On : 1 Lux or less, Off : 3 Lux more than
LED TYPE
8.Specifications
13
MENU DESCRIPTION
• The best clear image can be obtained color camera with
WDR(Wide Dynamic Range).
• The camera switches lenses automatically depending on the
illumination, which promotes the best possible color images during
the day and black / white image at night.
• The camera function can be controlled by OSD menu.
OSD STRUCTURE
9.OSD Menu
14
• ▲,▼: Menu up / down
• ◀,▶: Set-up Key
• Set: To move to a submenu item in the menu,
press this switch.
GENERAL STRUCTURE
SETUP
>LENS [┛]
EXPOSURE [┛]
WHITE BALANCE [┛]
WDR [┛]
DAY&NIGHT [┛]
IMAGE [┛]
SPECIAL [┛]
FACTORY DEFAULT
EXIT
LENS
>LENS TYPE ... DC
LEVEL ... 08
INITIAL
RETURN
EXPOSURE
>SHUTTER ... 1/60
FLICKERLESS ... OFF
AGC ... MID
DSS ... 10x
INITIAL
RETURN
WHITE BALANCE
>WB MODE ... ATW
RED CONT ... ----
BLUE CONT ... ----
PUSH CONT ... ----
INITIAL
RETURN
WDR
>WDR MODE ... OFF
WDR LEVEL ... 08
BLC ... OFF
BLC ZONE ... CENTER
BLC LEVEL ... 04
INITIAL
RETURN
9.OSD Menu
15
MOTION DET
>MOTION MODE ... OFF
ZONE ... WHOLE
LEVEL ... 03
INITIAL
RETURN
PRIVACY
>ZONE ... 0
MASK ... OFF
POSTION ... [┛]
INITIAL
RETURN
DAY & NIGHT
>D&N MODE ... COLOR
LEVEL ... ----
DWELL TIME ... ----
INITIAL
RETURN
IMAGE
>REVERSE ... NORMAL
SHARPNESS ... 10
FREEZE ... OFF
D-ZOOM .. 1,00x
INITIAL
RETURN
SPECIAL
>CAM TITLE ... 001
LANGUAGE ... ENG
SYNC ... ZNT
COMM ADJ ... [┛]
PRIVAC ... [┛]
MOTION DETECT ... [┛]
DISPLAY ... [┛]
INITIAL
RETURN
CAM TITLE
0123456789ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?*#$%()<>{}
SPACE
>> <<BACK
LOCATION ... [┛]
RETURN
DISPLAY
>CAM ID ... OFF
CAM TITLE ... OFF
MOTION ... OFF
INITIAL
RETURN
CAM TITLE
CAMM ADJ
>CAM ID ... 000
BAUDRATE ... 9600
INITIAL
RETURN
>LOCATION ...[+]
WIDTH/HIGHT ...[+]
RETURN
9.OSD Menu
16
LENS MENU STRUCTURE
EXPOSURE MENU STRUCTURE
9.OSD Menu
17
WHITE BALANCE MENU STRUCTURE
WDR MENU STRUCTURE
9.OSD Menu
18
DAY & NIGHT MENU STRUCTURE
IMAGE MENU STRUCTURE
9.OSD Menu
19
SPECIAL-CAM TITLE
SPECIAL-LANGUAGE
9.OSD Menu
9.OSD Menu
20
Table of contents
Other WDR Security Camera manuals
