HI-09UCS / HI-09FCS TECHNICAL BOOKLET
2.6
2.23
1.8
THICKNESS ADJUSTMENT
If you needto adjust thethickness of coinsto be accepted,
just use asmall slotted screwdriver, plug intothe slot and
rotate to fitthe thickness youwant.
RECORD MODE
If you wantto enter therecord mode, setDIP4, DIP5 ofthe DIP
SWITCH to "ON"positions. Thenturn on thepower.
SELECT OUTPUTPULSE WIDTH
If you wantto appoint thepulse width (50msor 100ms, defaultsetting is 100ms),
you must enterthe "RECORD MODE"first. Thenset DIP4 tothe following position.
1.50ms: DIP4to "OFF"
2.100ms DIP4to "ON"
After appointing thepulse width. Enterthe "MEMORIZE COINS"item to begin
memorizing the coins.
CLEAR RECORD FOR SINGLE CHANNEL
The multi coinselector has 8channels to record. Its8 channels represent itcan
record 8kinds of coinsseparately. Ifyou want toclear achannel, please proceed
as follows:
Turnoff the powerfor thenext operationas soon as stepsA,B,C,D iscomplete.
3.Insert onecoin of thefirst kind, thevalue "1/2" willbe memorized inthe set.Then insert one
coin of thefirst kind again,the new value"1/2" will beadded to theprevious "1/2", hencethe
set outputs "1"pulse. To this analogizes.Insert one coinof the 8thkind, the setoutputs "10" pulses.
4.The pulsesgenerated above-mentioned outputvia "IMPULSE" fromthe control board(pcb-09-2).
Besides, one coinbeing inserted willoutputs "one" pulsevia "output ch"corresponded
to its coinchannel(see Impulse andchannel ratio table).For example: Under"channel 5" with
"ratio list 3".Insert one coinwill result inoutputting 8 pulsesvia "IMPULSE" fromthe control
board, and outputting1 pulse via"output ch5" simultaneously.
If the ratiotable can't meetcustomer requirements, pleasecontact the originalfactory.
MEMORIZE COINS
1.You must enterthe "RECORD MODE"first. Then makesure which channelyou
want to saveby setting DIP1,DIP2, DIP3 tothe appropriate positions.Then insert
10 coins ofthe same currencyand makings. Thecoin selector magnetwill operate
three times toindicate a correctoperation. Then besure to turnthe power offfor
the next operation.
2.If anotherdifferent coins isnecessary to memorize,please repeat theoperation
above- mentioned again.
3.If somechannels of theset were memorizedsome time ago,please clear therecords
for all channelsfirst. HUAI I ELECTRONICS CO.,LTD
RATIOLIST CHOICES
1.Under "OPERATION MODE", theswitch DIP3, DIP2,DIP1 positions areassigned to 8ratio lists.
2.Under "RECORDMODE", the switchDIP3, DIP2, DIP1positions are assignedto 8 coinchannels.
OPERATIONMODE
1.Set DIP4,DIP5 to the"OFF" position whenthe power isoff.
2.Turnon the power, and setthe DIP3, DIP2,DIP1 positions to
correspond the ratiolist you need.
3.Now youcan start usingthe multi coinselector.
THREE OUTPUTINTERFACE
(1) 10p signalcable + controlboard for HI-09FCS/HI-09UCS
(2) 5p signalwire use forHI-09FCS connecting togame board andmeter.
(3) 6p signalwire use forHI-09UCS connecting togame board andmeter.
List 1 List 2 List 3 List 4 List 5 List 6 List 7 List 8
00000 10000 01000 11000 00100 10100 01100 11100
Other
Output
TerminalOperation
Mode Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count 1 Pulse
Output
Coin 1 1/2 1/4 111/2 1/2 1/2 1/4 Output ch1
Coin 2 11/2 111111/2 Output ch2
Coin 3 11/2 221322/3 Output ch3
Coin 4 21422653Output ch4
Coin 5 4284512 66Output ch5
Coin 6 5284NA NA 10 7Output ch6
Coin 7 8410 10 NA NA 12 NA Output ch6
8kindsofcoins
simultaneously
Coin 8 10 510 10 NA NA NA NA Output ch6
