Weil-McLain GOLD CGs Guide

GOLD CGs
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
•Do not try to light any appliance.
•Do not touch any electrical switch; do not use any phone in your
building.
•Immediately call your gas supplier from a neighbor’s phone. Follow
the gas supplier’s instructions.
•If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency
or the gas supplier.
If the information in this manual is not followed exactly, a fire or
explosion may result, causing property damage, personal injury or
loss of life.
Gas-Fired Water Boiler
User’s
Information
Manual
PartNo.550-110-261/0999

GOLD CGs — User’s Information Manual
2PartNo.550-110-261/0999
The following defined terms are used throughout this manual to bring attention to the pres-
ence of hazards of various risk levels or to important information concerning the life of the
product.
Hazard definitions
Please read this page first
Indicatespresenceofhazardsthatwill cause severepersonalinjury,death
or substantial property damage.
Indicates presence of hazards that can cause severe personal injury,
death or substantial property damage.
Indicates presence of hazards that will or can cause minor personal
injury or property damage.
Indicates special instructions on installation, operation or maintenance
that are important but not related to personal injury or property damage.
The User’s Information Manual provides information to the boiler owner/user for routine
operationand maintenance and emergencyshutdown. Detailed information onboiler instal-
lation,operation,start-up,serviceandpartsisincludedintheCGs Boiler Manual.TheCGs
Boiler Manual is intended only for use by a qualified service technician.
Boiler service and
maintenance
How to use this
manual . . .
To . . . Read/use . . . Pages . . .
Learn
precautions Warnings and definitions 1, 2, and 3
Prevent air
contamination
Laundry room or pool — make sure boiler air
is piped to boiler per manual.
Read list of air contaminants you must avoid.
Have boiler air piped in if you can’t avoid.
4
Maintain
boiler
Set up a plan for maintaining the boiler using
the schedule included in this manual.
Schedule an annual start-up by a qualified ser-
vice technician before every heating season.
5 –9
Locate boiler
components
How the boiler works and illustration. 10 –11
Start —or —
Shutdown
boiler
Use the Lighting instruction sheet for the gas
valve installed on your boiler. Ask your service
technician if you are unsure which one. 12 or 13
Troubleshoot
common
problems
Use the common problems/solutions table to
resolve typical heating system/boiler problems. 14 –15

GOLD CGs —User’s Information Manual
3PartNo.550-110-261/0999
Failure to adhere to the guidelines on this page can result in se-
vere personal injury, death or substantial property damage.
Boiler service and maintenance —
• To avoid electric shock, disconnect electrical supply before per-
forming maintenance.
• Toavoidsevereburns,allow boiler to cool beforeperformingmain-
tenance.
• You must maintain the boiler as outlined in the manual and have the
boiler started up and serviced at least annually by a qualified
service technician to ensure boiler/system reliability.
Boiler operation —
•Do not block flow of combustion or ventilation airtoboiler.This
boiler is equipped with a control which will automatically shut down
the boiler should air or vent be blocked. If vent or air blockage is
easily accessible and removable, remove it. The boiler should attempt
to restart within an hour. If blockage is not obvious or cannot be re-
moved,have the boiler and system checked by a qualified service tech-
nician.
• Should overheating occur or gas supply fail to shut off, do not
turn off or disconnect electrical supply to pump. Instead, shut off
the gas supplyatalocationexternal to the appliance.
•Do not use this boiler if any part has been under water.Immedi-
ately call a qualified service technician to inspect the boiler and to
replace any part of the control system and any gas control, which has
been under water.
•Have the building monitored when it is vacant for an extended
period. Safety controls can shut down the boiler at any time. The loss
of heat can result in significant damage due to freezing.
Boiler water —
• DO NOT use petroleum-based cleaning or sealing compounds in
boiler system.Water seal deterioration will occur, causing leakage be-
tween sections and damage to heating system components. This can
result in substantial property damage.
• DO NOT use "homemade cures" or "boiler patent medicines".
Serious damage to boiler, personnel and/or property may result.
• Continualfreshmakeup water will reduce boiler life.Mineralbuild-
up in sections reduces heat transfer, overheats cast iron, and causes
section failure. Addition of oxygen and other gases can cause internal
corrosion. Leaks in boiler or piping must be repaired at once to pre-
vent makeup water.
•Do not add cold water to hot boiler.Thermalshockcancausesec-
tions to crack.
STOP!! —Read before proceeding

GOLD CGs —User’s Information Manual
4PartNo.550-110-261/0999
Air contamination
Common household and hobby products often con-
tain fluorine or chlorine compounds. When these
chemicalspassthroughtheboiler,theycanformstrong
acids in the vent system or boiler. The acid can eat
through the vent or boiler wall, causing serious dam-
If the boiler is installed in any area likely to cause contamination, or if products which
wouldcontaminatetheaircannotberemoved,youmustpipe combustion air to the boiler
air intake. Contaminated combustion air will damage the boiler and vent system, resulting in
possible severe personal injury, death or substantial property damage.
Do not operate a CGs boiler in a laundry room or pool facility, for example,without
using ducted outside air. These areas will always contain contaminants.
age and presenting a possible threat of flue gas spillage
into the building.
Please read the information below. If the contaminat-
ing chemicals will be present, have your installer pipe
the boiler air from outside per the Boiler Manual.
Prevent combustion air contamination
Products to avoid Areas likely to have contaminants
Spray cans containing chloro/fluorocarbons Dry cleaning/laundry areas and establishments
Permanent wave solutions Swimming pools
Chlorinated waxes/cleaners Metal fabrication plants
Chlorine-based swimming pool chemicals Beauty shops
Calcium chloride used for thawing Refrigeration repair shops
Sodium chloride used for water softening Photo processing plants
Refrigerant leaks Auto body shops
Paint or varnish removers Plastic manufacturing plants
Hydrochloric acid/muriatic acid Furniture refinishing areas and establishments
Cements and glues New building construction
Antistatic fabric softeners used in clothesdryers Remodeling areas
Chlorine-type bleaches, detergents, and cleaning
solvents found in household laundry rooms Garages with workshops
Adhesives used to fasten building products and
other similar products

GOLD CGs —User’s Information Manual
5PartNo.550-110-261/0999
Maintain boiler using schedule below
Service technician
(covered in CGs Boiler Manual —
for use only by a qualified service technician)
Owner maintenance
(see following pages for instructions)
A
NNNUAL
START
-
UP
Inspect:
• Reported problems
• Boiler area
• Air openings
• Flue gas vent system (and air piping)
• Pilot and main burner flames
• Water piping
• Boiler heating surfaces
• Burners, base and inlet air box
• Condensate drain system
Service:
• Inducer motor
• Oiled-bearing circulators
Start-up:
• Perform start-up per manual
Check/test:
• Gas piping
• Cold fill and operating pressures
• Air vents and air elimination
• Limit controls and cutoffs
• Expansion tank
• Boiler relief valve
Review:
• Review with owner
Daily
• Check boiler area
• Check air openings
• Check boiler pressure/
temperature gauge
Monthly
• Check boiler interior piping
• Check venting system
• Check air vents
• Check boiler relief valve
• Check condensate drain system
• Check automatic air vents (if
used)
Periodically
• Test low water cutoff (if used)
• Clean vent termination/air intake
screens
Every 6 months • Oil inducer motor
• Operate relief valve
End of season • Shut down procedure

GOLD CGs —User’s Information Manual
6PartNo.550-110-261/0999
User maintenance procedures
Check boiler areaCheck boiler area
Check boiler areaCheck boiler area
Check boiler area
The boiler should be inspected and started annually, at the beginning of
the heating season, only by a qualified service technician. In addition, the
maintenanceandcareoftheboilerdesignatedonpage5andexplainedon
the following pages must be performed to assure maximum boiler effi-
ciency and reliability. Failure to service and maintain the boiler and sys-
tem could result in equipment failure, causing possible severe personal
injury, death or substantial property damage.
The following information provides detailed instructions for completing
the maintenance items listed in the maintenance schedule, page 5. In ad-
dition to this maintenance, the boiler must be serviced and started up at
the beginning of each heating season by a qualified service technician.
❏Check daily . . . . . . . . . . . .
❏Boiler must be serviced & maintained
this manual. If any of these products are in the
room from which the boiler takes its combustion
air, they must be removed immediately or the
boiler combustion air must be supplied from out-
side. See WARNING above.
Check air openingsCheck air openings
Check air openingsCheck air openings
Check air openings
1. Verify that combustion and ventilation air open-
ings to the boiler room and/or building are open
and unobstructed.
2. Verify that boiler vent discharge and air intake are
clean and free of obstructions. Remove any debris
on the air intake or flue exhaust openings.
Check boiler pressure/Check boiler pressure/
Check boiler pressure/Check boiler pressure/
Check boiler pressure/
temperature gaugetemperature gauge
temperature gaugetemperature gauge
temperature gauge
1. Make sure the pressure reading on the boiler pres-
sure/temperature gauge does not exceed 24 psig.
Higher pressure may indicate a problem with the
expansion tank.
Contact a qualified service technician if problem
persists.
To prevent potential of severe personal injury, death
orsubstantial property damage, eliminate all materials
discussed below from the boiler vicinity. If contami-
nants are found:
Remove products immediately from the area. If they
havebeenthereforanextendedperiod,callaqualified
service technician to inspect the boiler and vent sys-
tem for possible damage from acid corrosion.
If products cannot be removed, immediately call a
qualified service technician to install an outside com-
bustion air source for the boiler (if not already in-
stalled).
1. Combustible/flammable materials —Do not store
combustible materials, gasoline or any other flam-
mable vapors or liquids near the boiler. Remove
immediately if found.
2. Air contaminants —Products containing chlorine
or fluorine, if allowed to contaminate the boiler
intake air, will cause acidic condensate in the vent
and boiler. This will cause significant damage to
the vent and/or boiler if allowed to continue. Read
the list of potential materials listed on page 4 of

GOLD CGs —User’s Information Manual
7PartNo.550-110-261/0999
User maintenance procedures continued
Check boiler interior piping
1. Remove boiler jacket top.
2. Visually inspect for leaks around internal piping,
circulators, relief valve and other fittings. Immedi-
atelycallaqualifiedservicetechniciantorepairany
leaks.
Check venting system
1. Visually inspect the flue gas vent piping for any
signs of blockage, leakage or joints or deteriora-
tion of the piping. Notify your qualified service
technician at once if you find any problem.
❏Check monthly . . . . . . . . . . . .
Figure 2 —Automatic air vent
Figure 1 — Relief valve
Have leaks fixed at once by a qualifed service techni-
cian. Continual fresh makeup water will reduce boiler
life. Minerals can build up in sections, reducing heat
transfer,overheatingcastiron,andcausingsectionfail-
ure.
Do not use petroleum-based cleaning or sealing com-
pounds in boiler system. Severe damage to boiler and
system components can occur, resulting in possible
severe personal injury, death or substantial property
damage. Check automatic air vents (if
used)
1. SeeFigure 2.
2. Remove the cap from any automatic air vent in
thesystemandcheckoperationbydepressingvalve
B slightly with the tip of a screwdriver.
3. If the air vent valve appears to be working freely
and not leaking, replace cap A, twisting all the way
on.
4. Loosen cap A one turn to allow vent to operate.
5. Have vent replaced if it does not operate correctly.
Check boiler relief valve
1. Inspect the boiler relief valve (see Figure 1) and
the relief valve discharge pipe for signs of weeping
or leakage.
2. If the relief valve often weeps, the expansion tank
may not be working properly. Immediately con-
tactyour qualified service technician to inspect the
boiler and system.
Failure to inspect the vent system as noted above and
havethemrepairedby aqualifedservice techniciancan
result in vent system failure, causing severe personal
injury or death.
Check condensate drain system
1. Inspectcondensatedrainfittingsandtubing.Verify
that condensate can flow freely to drain.

GOLD CGs —User’s Information Manual
8PartNo.550-110-261/0999
User maintenance procedures
Operate boiler relief valve
1. Before proceeding, verify that the relief valve out-
lethasbeenpipedtoasafeplaceofdischarge,avoid-
ing any possibility of scalding from hot water.
To avoid water damage or scalding
due to valve operation, a metal dis-
charge line must be connected to
relief valve outlet and run to a safe
placeofdisposal.Thisdischargeline
must be installed by a qualifed
heating installer or service techni-
cianinaccordancewiththeinstruc-
tions in the Boiler manual. The
discharge line must be terminated
so as to eliminate possibility of se-
vere burns should the valve dis-
charge.
2. Read the boiler pressure/temperature gauge to
make sure the system is pressurized.
3. Lift the relief valve top lever slightly, allowing wa-
ter to relieve through the valve and discharge pip-
ing.
4. If water flows freely, release the lever and allow the
valve to seat.Watch the end of the relief valve dis-
Clean vent termination & air
intake screens
1. Remove all lint and debris from both the boiler air
intake screen and the flue discharge screen.
2. The boiler control module will sense blockage of
the air intake or flue and lockout if the blockage is
excessive. It will signal the failure by flashing the
appropriate indicator lights on the control board.
3. If removing the debris does not allow the boiler to
operate correctly afterwards, contact your qualifed
Oil inducer motor
1. Use only S.A.E.20 motor oil.DO NOT use house-
hold universal oils.
Use only S.A.E. 20 motor oil to lu-
bricate the inducer motor. Do not
use common universal household
oils.
2. Place a few drops of oil in each of the two oiler
cups on the inducer motor.
❏Service periodically . . . . . . . . . . . .
❏Service every 6 months . . . . . . . . .
service technician to inspect the boiler and vent/
air systems.
Test low water cutoff (if
installed)
1. If the system is equipped with a low water cutoff,
test the low water cutoff periodically during the
heating season, following the low water cutoff
manufacturer’s instructions.
charge pipe to ensure that the valve does not weep
after the line has had time to drain. If the valve
weeps,lifttheseatagaintoattempttocleanthevalve
seat.Ifthevalvecontinuestoweepafterwards,con-
tactyour qualified service technicianto inspect the
valve and system.
5. If water does not flow from the valve when you lift
thelevercompletely,thevalveordischargelinemay
be blocked. Immediately shutdown the boiler, fol-
lowing the instructions on the inside jacket top
Lighting Instructions. Call your qualified service
technician to inspect the boiler and system.

GOLD CGs —User’s Information Manual
9PartNo.550-110-261/0999
User maintenance procedures continued
Follow boiler shutdown procedure
1. Follow“TO TURN OFF GAS TO APPLIANCE”on the Lighting in-
structions on the inside of the jacket top panel. You will also find
theseinstructionsonpages 12and 13of this manual.Use theLighting
instruction for the gas valve model installed on the boiler.
2. Do not drain system unless exposure to freezing temperatures will
occur.
3. Do not drain the system if it is filled with an antifreeze solution.
4. Do not shut down boilers used for domestic water heating. They must
operate year-round.
❏End-of-season shutdown . . . . . . . .

GOLD CGs —User’s Information Manual
10 PartNo.550-110-261/0999
How the boiler works . . .
①Control module
The control module responds to signals from the room thermostat, air pressure switch and
boiler limit circuit to operate the boiler circulator, pilot burner, gas valve and inducer.When
room thermostat calls for heat, the control module starts the system circulator and inducer.
The control module runs the inducer long enough to purge the boiler flue passages, then
opens the pilot valve and activates pilot ignition spark.
The control module allows up to 15 seconds to establish pilot flame. If flame is not sensed
within 15 seconds, the control module will turn off the gas valve, flash the Flame light, and
then enter a 15-second postpurge. The control module will then start a new cycle. This will
continueindefinitely until pilot flame isestablished or power is interrupted.Once pilot flame
is proven, the control module opens the gas valve to allow main burner flame.
When the room thermostat is satisfied, the control module turns off the gas valve, operates
the inducer for a 15-second postpurge and waits for the next heat call.
The control module indicator lights show normal sequence when the lights are on steady.
When a problem occurs, the control module flashes combinations of lights to indicate the
most likely reason for the problem.
②Transformer
The control transformer reduces line voltage to 24 volts for the gas valve and limit circuit.
③Inducer
The inducer pulls flue gases through the boiler, causing air to be pulled in through the air
intake opening. The inducer pushes the flue gases through the vent pipe as well.
④Air pressure switch
The air pressure switch signals the control module, telling the control module whether air is
moving through the inducer.
⑤Water temperature limit switch
The water temperature limit switch turns off the gas valve if the temperature in the boiler
goes above its setting. (The circulator will continue to run as long as there is a call for heat.)
⑥Boiler circulator
The boiler circulator circulates water through the external (system) piping. NOTE —The
control module provides a pump exercising routine. If the boiler is not operated for 30 days,
the control module will power the circulator for 30 seconds, then off.
asupply to system
breturn from system
ccombustion air inlet
dflue outlet
egas valve
fpressure/temperature gauge
grelief valve (not visible)
hair vent connection
iflame rollout switch
jair inlet box
kpilot burner and bracket
lstainless steel burners
mcast iron boiler sections
nflue collector
ojunction box
Other boiler components:

GOLD CGs —User’s Information Manual
11PartNo.550-110-261/0999
GOLD CGs Gas-Fired Induced-Draft Water Boiler

GOLD CGs —User’s Information Manual
12 PartNo.550-110-261/0999
Lighting instructions
Beforeattemptingtostarttheboiler,check the boiler
pressure temperature gauge.
Ifboilerandsystemarefullofwaterandproperlypres-
surized, the gauge should read at least 12 psig on most
systems.
Operatingtheboiler withoutproper watercontentwill
damage boiler and controls and could result in severe
personal injury, death or substantial property damage.

GOLD CGs —User’s Information Manual
13PartNo.550-110-261/0999
FOR YOUR SAFETY READ BEFORE OPERATING
OPERATING INSTRUCTIONS
TO TURN OFF GAS TO THE APPLIANCE
•Do not try to light any appliance.
•Do not touch any electric switch; do not use
any phone in your building.
•Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
•If youcannotreachyourgas supplier,call thefire department.
WHAT TO DO IF YOU SMELL GAS
A. This appliance does not have a pilot. It is
equipped with an ignition device which auto-
matically lights the burner. Do not try to light
the burner by hand.
B. Before OPERATING, smell all around the ap-
plianceareaforgas.Besuretosmellnexttothe
floor because some gas is heavier than air and
will settle on the floor. See below.
C. Use only your hand to turn the gas control knob. Never use
tools. If the knob will not turn by hand, don't try to repair it,
call a qualified service technician. Force or attempted repair
may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control, which has been under water.
If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
1. STOP! Read the safety information above on this label.
2. Set the thermostat to lowest setting.
3. Turn off all electrical power to the appliance.
4. Remove jacket front panel.
5. Thisapplianceisequippedwithanignitiondevicewhichautomaticallylightstheburner.
Do not try to light the burner by hand.
6. TurnGas control knob clockwise to OFF.
7. Wait five (5) minutes to clear out any gas.Then smell for gas,including near the floor.If
yousmell gas, STOP! Follow "B"in the safety information above. If you don't smell gas,
go to the next step.
8. Turn Gas control knob counterclockwise to ON.
9. Turn on all electric power to the appliance.
10. Set thermostat to desired setting.
11. If the appliance will not operate, follow the instructions "TO TURN OFF GAS TO
APPLIANCE" below and call your service technician or gas supplier.
12. Replace jacket front panel.
1. Set the thermostat to lowest setting.
2. Turn off all electric power to the appliance if service is to be performed.
3. Remove jacket front panel.
4. TurnGas control knob clockwise to OFF. Do not force.
5. Replace jacket front panel.
Lighting instructions

GOLD CGs —User’s Information Manual
14 PartNo.550-110-261/0999
Common problems and solutions
Symptom Common Causes Possible Corrections
Rapid cycling —boiler
turns on and off frequently
Thermostat installed where drafts
or heat affect reading Locate thermostat on inner wall away from heat sources or cool drafts.
Heat anticipator in thermostat
adjusted incorrectly Adjust thermostat per manufacturer’s instructions.
Incorrect limit setting Set limit according to system needs.
Maximum setting is 220˚F. Increase limit
setting to decrease cycling.
Insufficient water flow through
boiler Check all valves to and from boiler. Return to proper setting.
Confirm circulator size.
Frequent release of water
through relief valve
Expansion tank sized too small Call qualified service technician to check
expansion tank operation and size.
Flooded expansion tank Call qualified service technician to check
expansion tank operation.
Inoperative limit control Call qualified service technician to replace
limit control.
Need to frequently add
makeup water
Leaks in boiler or piping Have qualified service technician repair
leaks at once to avoid constant use of
makeup water. Makeup water can cause
mineral deposits which, in turn, can cause
boiler section failure. Do not use petroleum-
base stop-leak compounds.
Black water condition
Oxygen corrosion due to leaks in
boiler and piping Have qualified service technician repair at once. Keep pH of water between 7.0 to 8.5.

GOLD CGs —User’s Information Manual
15PartNo.550-110-261/0999
Common problems and solutions
Symptom Common Causes Possible Corrections
Popping or percolating
noise heard in boiler Mineral deposits in sections due to
constant use of makeup water Call qualified service technician to de-lime boiler, if necessary. In some cases,
deposits will be too heavy to remove with
de-liming procedures.
Have qualified service technician repair
leaks to eliminate need for constant
makeup water.
Incorrect pH of boiler water Call qualified service technician to check
pH level and correct. pH should be
maintained between 7.0 to 8.5.
Insufficient water flow through
boiler Check all valves to and from boiler. Return to proper setting.
Confirm circulator size.
Metal flakes found in vent
outlet or vent —flueway
corrosion
Contaminated combustion air
supply —See page 4 in this
manual.
Remove any contaminating products. See
page 4 in this manual.
Provide outside air for combustion. Kit
available through Weil-McLain distributor.
Have qualified service technician pipe-up
kit.
Condensation of combustion
gases in boiler sections Have qualified service technician inspect system piping and controls to verify proper
regulation of return water temperature.
Some radiators or
baseboard units do not
heat or are noisy
Air in system Bleed air from system through air vents in
radiators or baseboard units.
Low system pressure Fill to correct pressure.
Check for leaks in boiler or piping. Have
qualified service technician repair at once.
High limit set too low Adjust high limit to higher setting.

16 PartNo.550-110-261/0999
Weil-McLain LimitedWarranty for
Residential & Commercial Cast Iron Boilers
Weil-McLain
500 Blaine Street
Michigan City, IN 46360-2388
http://www.weil-mclain.com
◆ ◆
◆ ◆
◆ RESIDENTIALWATERWARRANTY—LimitedLifetime
◆ ◆
◆ ◆
◆ RESIDENTIALSTEAMWARRANTY—Limited10Year
◆ ◆
◆ ◆
◆ COMMERCIAL WARRANTY—Limited 10-Year
NOTE: The residential steam and water warranties do not
coverresidential boilers installed in buildings otherthanone or
twofamilydwellingunits,unlessthey arebuildingswith individual
boilers foreach dwelling unit.
FirstYear-(All Residential & Commercial Cast Iron
Boilers)
LimitedWarranty for Cast Iron Boilers:
Weil-McLain warrants that its cast iron boilers are free from
defectsin material andworkmanship for oneyearfrom thedate
ofinstallation. Ifanypartsarefoundtobedefectiveinmanufacture,
Weil-McLainwill provide replacementof such defectiveparts.
SecondThroughTenthYear-(ResidentialWater/Steam)
SecondThroughTenthYear-(CommercialWater/Steam)
LimitedWarranty for cast iron sections:
Weil-McLainwarrantsthatthecastironsectionsofits waterand
steam boilersarefree fromdefectsinmaterialandworkmanship
fromthedate ofinstallationforthesecondthroughthe tenthyear.
If,during such time period,any section is foundtobe defective,
Weil-McLain will provide replacement for the original cast iron
section(s).
EleventhYear and Beyond - (ResidentialWater Only)
Limited Warranty for Cast Iron Sections:
Weil-McLainwarrantsthatthecastironsectionsofits residential
waterboilers arefree fromdefectsin materialand workmanship
forthe eleventh yearandbeyond fromthedate of installation.If,
duringsuch time period,anysection(s) isfoundto be defective,
Weil-McLain will provide replacement for the original cast iron
section(s)uponthepaymentof aproportionate chargebasedon
thetimethe boilerhasbeen inservice. Theproportionate charge
will be equal to the appropriate percentage of the list price of
suchsection(s)at the time the warranty claimismade, and will
bedeterminedasfollows:
11th year - 5%; 12th year - 10%; 13th year - 15%;
14th year - 20%; 15th year - 25%; 16th year - 30%;
17th year - 35%; 18th year - 40%; 19th year - 45%;
20th year - 50%; 21st year - 55%; 22nd year - 60%;
23rd year - 65%; 24th year - 70%; 25th year and
beyond - 75%.
All Residential & Commercial Cast Iron Boilers
These warranties are subject to the condition that the boiler
musthavebeen installedbya heatingcontractorwhose principal
occupationisthesaleandinstallationofplumbing,heatingand/or
airconditioningequipment.
These warranties do not cover:
1. Componentsthat are part oftheheating systems, but
werenot furnishedbyWeil-McLainas a partofthe boiler.
2. Theworkmanshipof anyinstaller ofWeil-McLain’sboilers.
Inaddition, this warrantydoesnot assume any liabilityof
anynaturefor unsatisfactory performance caused by
improperinstallation.
3. Anycosts for labor for removalandreinstallation of the
allegeddefective part,transportation to Weil-McLain,if
necessary,andany other materials necessary to perform
theexchange.
4. Improperburner adjustments, control settings,careor
maintenance. Informationisincludedintheinstallation
Instructions,Owner’sInformationManualand/or Start-up,
Serviceand Maintenance Instructions, andotherprinted
technicalmaterialfurnishedbyWeil-McLainwiththeboiler.
5. Boilersoperatedwithcombustion aircontaminated
externallyby chemical vapors orwithimproper fuel
additives,or with water conditionswhichmay have
causedunusual deposits in the cast ironsections.
Thesewarrantiesextendonlytothefirstretailpurchaserof the boiler
andonlytoaboilerthathasnotbeen movedfrom itsoriginal installation
site.
THE WARRANTIES DESCRIBED ABOVE ARE IN LIEU OF ALL
OTHERWARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOTLIMITEDTO ANY IMPLIEDWARRANTIES OF FITNESS FOR A
PARTICULARPURPOSE ANDMERCHANTABILITY. WEIL-McLAIN
EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY FOR
CONSEQUENTIAL, INCIDENTAL, INDIRECT OR PUNITIVE
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY.
Forprompt productwarranty claims,notify theinstallerwho, inturn, will
notifytheWeil-McLaindistributorfrom whomhe purchasedthe boiler. If
thisaction does not resultinwarranty resolution, contact Weil-McLain
Consumer Relations Department, 500 Blaine Street, Michigan City,
Indiana46360-2388,withdetailsinsupportofthewarrantyclaim. Alleged
defective part or parts must be returned through trade channels in
accordancewiththeWeil-McLainprocedurecurrentlyinforceforhandling
returned goods for the purpose of inspection to determine cause of
failure. Weil-McLainwillfurnishnewpart(s)toanauthorizedWeil-McLain
distributorwho,inturnwillfurnishthenewpart(s)totheheatingcontractor
whoinstalled the boiler. Ifyouhaveanyquestions about thecoverage
ofthiswarranty, contactWeil-McLainat the address above.