weintek mTV-100 User manual

User
Manual
mTV-100 Startup Guide

Table of Contents
1 Specification...........................................................................................................1
1.1 Dimensions.................................................................................................2
1.2 Connector pin designations .......................................................................3
1.3 USB Host port and SD card slot..................................................................3
1.4 Ethernet port..............................................................................................3
1.5 DIP switch...................................................................................................3
1.6 LED indicator ..............................................................................................4
1.7 CR1225 battery ..........................................................................................4
1.8 Power connection ......................................................................................4
1.9 HDMI Output..............................................................................................5
2 System Settings ......................................................................................................7
2.1 System Toolbar...........................................................................................7
2.2 System Information....................................................................................7
2.3 System Setting............................................................................................8
2.4 Upgrade firmware ......................................................................................9

mTV User Manual
V1.0.0
1
1Specification
Features
HD 720p High Resolution HDMI Output
One Gigabit Ethernet Port
Compact Design and DIN-rail Mountable
Built-in 256MB Flash Memory
SD Card Slot for Extension of Storage
One USB Host Port
Fan-less Cooling System
Supports MPI 187.5K
Power Isolator Inside
Memory
Storage (MB)
256
RAM (MB)
256
Processor
ARM Cortex A8 600MHz
I/O Port
SD Card Slot
SD/SDHC
USB Host
USB 2.0 x 1
USB Client
N/A
Ethernet
10/100/1G x 1
Com Port
COM1 RS-232,COM2 RS-485
2W/4W,COM3 RS-485 2W
CAN Bus
N/A
HDMI
Resolution 1280 x 720
RTC
Built-in (CR1225 3V lithium battery)
Power
Input Power
24±20%VDC
Power Consumption
230 mA@24V
Power Isolation
Built-in
Voltage Resistance
500VAC (1 min)
Isolation Resistance
Exceed 50Mat 500VDC
Vibration Endurance
10 to 25Hz(X,Y,Z direction 2G 30 minutes)
Specification
Enclosure
Plastic
Dimensions WxHxD
130 x 115 x 27mm
Weight (kg)
Approx. 0.18 kg
Mount
35mm Din rail mounting
Storage Temperature
-20°~ 70°C (-4°~ 158°F)
Operating
Temperature
-20°~ 55°C (-4°~ 131°F)
Relative Humidity
10% ~ 90% RH (non-condensing)
Certificate
Complies with CE
Software
EasyBuilder Pro V3.00.02 or later versions

mTV User Manual
V1.0.0
2
1.1 Dimensions
27,00
[1,063]
125,00
[4,921]
114,80
[4,520]
129,73
[5,107]
Front View Side View Side View
Top View
Bottom View
e
f
d
c
b
a
h
g
a
USB Host Port
e
HDMI
b
Ethernet Port
f
SD Card Slot
c
Com1 RS-232, Com2 RS-485 2W/4W,
Com3 RS-485 2W
g
DIP Switch
d
Power Connector
h
Reset Button

mTV User Manual
V1.0.0
3
1.2 Connector pin designations
PIN#
Symbol
COM1 RS-232
COM2 RS-485
COM3 RS-485
2W
4W
1
Data+
Data+
2
RxD
Received Data
3
TxD
Transmitted Data
4
Data-
Data-
5
GND
Signal Ground
6
RX+
Data+
RX+
7
RX-
Data-
RX-
8
TX+
TX+
9
TX-
TX-
1.3 USB Host port and SD card slot
USB 2.0 full speed host interface supports USB mouse devices, keyboards, printers, barcode
scanners, and USB disk. While using external hard drive, use external power supply. Do not use USB
port to charge external device. Insert SD card to be the extension of storage.
1.4 Ethernet port
The unit has one 10/100/1G Ethernet port.
The LED indicators on the Ethernet port indicate:
Orange LED: LAN link status
Green LED: Active status
1.5 DIP switch
Each HMI is equipped with a reset button and a DIP switch. When using DIP switch to change
modes, the corresponding functions will be triggered.
SW1
SW2
Mode
OFF
OFF
Normal mode
ON
OFF
Hide HMI System Setting Bar
OFF
ON
Boot loader mode
ON
ON
Restore factory default
Note: Reboot HMI after adjusting DIP switches to start the corresponding mode.

mTV User Manual
V1.0.0
4
1.6 LED indicator
LED indicators show the operation status of HMI.
Power (Orange)
Indicates power status.
CPU (Green)
Indicates CPU status.
Communication (Blue)
Indicates communication status, blinks during
communication. When communication is good, it may stay
on.
1.7 CR1225 battery
mTV-100 Series HMI requires a coin type lithium battery CR1225 to keep the RTC running.
Battery type: CR1225 3V lithium battery
1.8 Power connection
Power: The unit can be powered by DC power only, voltage range: 24±20% Volts DC, compatible
with most controller DC systems. The power conditioning circuitry inside the unit is accomplished
by a switching power supply. The peak starting current can be as high as 500mA.
Connection: To make a connection, strip about 3/8”of insulation off the end of the wire, turn the
connector screw counterclockwise until the gap is wide open, insert the wire all the way in, and turn
the screw clockwise until it is tight.
Note: Connect positive DC line to the ‘+’terminal and the DC ground to the‘-’terminal.

mTV User Manual
V1.0.0
5
1.9 HDMI Output
Supports 1280 × 720 high resolution HDMI output. Displays image via HDMI or DVI interface LED /
LCD.
Note: When mTV-100 enters backlight saver mode, an external keyboard or mouse is needed to
turn on the backlight. Since TD2220 Touch Display is in standby mode when the backlight is off,
touching the screen has no effect. To turn on the backlight again and enable touch screen, connect
an external keyboard or mouse to operate.
The following part shows different ways to connect HDMI.
Connect to DVI monitor.
Use HDMI-to-DVI converter to connect the monitor.
Note: mTV-100 supports resolution 1280x720p, please use DVI monitor / converter.
Directly connect to HDMI monitor.

mTV User Manual
V1.0.0
6
Use HDMI splitter to connect multiple HDMI monitors.
Use HDMI switch to connect two mTV-100 with one HDMI monitor.
Note: If not connecting a repeater, the maximum length of HDMI cable allowed is 15m. To reach a
longer distance, please use CAT6 cable or a repeater. HDMI converter is used to detect the monitor
and correctly output.

mTV User Manual
V1.0.0
7
2System Settings
For the first time operating the unit, please complete the following system settings. When finished,
the project files designed using EasyBuilder can be used on HMI.
2.1 System Toolbar
After rebooting HMI, users can set the system with [System Toolbar] at the bottom of the screen.
Normally, this bar is hidden automatically. Only by touching the target at the bottom-right corner of
the screen will the System Toolbar pop up.
Text and number keyboard Number keyboard
How to hide HMI System Setting Toolbar
When [DIP Switch 1] is set ON, the system setting toolbar is disabled. When set OFF; the system
setting toolbar is enabled. Please restart HMI to enable/disable the toolbar.
System register [LB-9020] can also enable/disable system setting toolbar
When [LB-9020] is set ON, the toolbar is displayed, and set OFF to hide the toolbar.
2.2 System Information
Network: Displays network information &
HMI IP address.
Version: Displays HMI system version.

mTV User Manual
V1.0.0
8
2.3 System Setting
Set or modify system parameters.
Confirm password for security.
■Network
Download project to HMI via Ethernet.
Confirm IP address of target HMI.
Select to obtain IP address automatically or
specify an IP address.
■Time/Date
Sets HMI local time/date.
■Security
Password protection, the default is 111111.
[Password for entering system]
[Password for uploading project]
[Password for downloading project]
[Password for uploading history data]
■History
Clears history data in HMI.
[Recipe] / [Eventlog] / [Datalog]
■HMI name
Sets HMI name to identify HMI during
download/upload process and avoid
remembering each HMI IP address.