Weldex WDP-4602MXV User manual

V.1.0

Acknowledgment
Company and product names published in this manual are trademarks or registered trademarks of
their respective owners.
If this document is translated from the original English version by Weldex Corporation, all reasonable
endeavors will be used to ensure the accuracy of translation. Weldex Corporation shall not be liable for
any translation errors contained herein or for incidental or consequential damages in connection with
the furnishing or use of this translated material.
Due to continuous development of our products, the information in this document is subject to change
without notice. Weldex Corporation shall not be liable for errors contained herein or for incidental or
consequential damages in connection with furnishing or use of this material. Contents of this
publication may be preliminary and/or may be changed at any time without any obligation to notify
anyone of such revision or change, and shall not be regarded as a warranty.
DISCLAIMER
•While every effort has been made to ensure that the information contained in this guide is accurate
and complete, no liability can be accepted for any errors or omissions.
•Weldex Corporation reserves the right to change the specifications of the hardware and software
described herein at any time without prior notice.
•No part of this guide may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language in any form, by any means, without prior written permission of Weldex
Corporation
• Weldex Corporation makes no warranties for damages resulting from corrupted or lost data due to a
mistaken operation or malfunction of the Digital Video Recorder, the software, the hard drives,
personal computers, peripheral devices, or unapproved / unsupported devices.

3
This document contains confidential and proprietary information of Weldex Corporation.
TABLE OF CONTENTS
WDP-4602MXV USER MANUAL
INTRODUCTION
Features-----------------------------------------------------------------------------------5
Package Contents -----------------------------------------------------------------------6
Specifications ----------------------------------------------------------------------------7
INSTALLATION
Hardware Overview ------------------------------------------------------------------10
Disassembling--------------------------------------------------------------------------11
Installing the camera on a wall ---------------------------------------------------12
PCB Board Layout of the camera --------------------------------------------------13
Connection - sensor input and alarm output-------------------------------------14
Dimensions-----------------------------------------------------------------------------15
NETWORK INSTALLATION & SETUP
Network Initial Setup ----------------------------------------------------------------16
IP Scan Tool ----------------------------------------------------------------------------17
VLC Player Installation ---------------------------------------------------------------19
WEB Viewer
WEB Viewer Login --------------------------------------------------------------------21
Live View Functions ----------------------------------------------------------------22
Configuration - AUDIO&VIDEO
Video Profile ----------------------------------------------------------------24
Video Setup ------------------------------------------------------------------25
TABLE OF CONTENTS

4
This document contains confidential and proprietary information of Weldex Corporation.
WDP-4602MXV USER MANUAL
Configuration - AUDIO&VIDEO
Audio Setup -----------------------------------------------------------------26
Camera Setup --------------------------------------------------------------- 27
Configuration - NETWORK
TCP/IP ------------------------------------------------------------------------30
PORT --------------------------------------------------------------------------31
SNMP -------------------------------------------------------------------------32
DDNS -------------------------------------------------------------------------33
HTTPS ------------------------------------------------------------------------34
IP FILTER --------------------------------------------------------------------35
UPnP/BONJOUR-------------------------------------------------------------36
Configuration - EVENT
FTP ----------------------------------------------------------------------------37
SMTP -------------------------------------------------------------------------38
SCHEDULE -------------------------------------------------------------------39
MOTION DETECTION ------------------------------------------------------40
SENSOR ----------------------------------------------------------------------42
NETWORK UNLINKED ----------------------------------------------------43
Configuration - SYSTEM
INFORMATION --------------------------------------------------------------44
USER --------------------------------------------------------------------------45
DATE/TIME -----------------------------------------------------------------46
MAINTENANCE -------------------------------------------------------------47
LOG ---------------------------------------------------------------------------49
TROUBLESHOOTING
Troubleshooting -----------------------------------------------------------------50
TABLE OF CONTENTS

Features
Features
•2Megapixel Full HD IP Height Strip Camera
•Up to 30fps @1080p (H.264)
•Progressive Scan
•Dual Streaming (H.264 & MJPEG)
•Power over Ethernet
•Covert Design Housing
•F2.0 f=4.3mm Fixed Corn Lens
5
This document contains confidential and proprietary information of Weldex Corporation.
This manual provides information on installation and operation of the WDP-4602MXV IP camera. The
WDP-4602MXV is a stand alone, non-PC based, fully embedded video codec capable of encoding video
and audio from an analog video/audio source in real time.
INTRODUCTION
PC Requirements
•CPU : Intel Core2Duo 2.4GHz or above
•Memory : 2 GB or above
•Resolution : 1024x768 or higher
•Operating system : Window XP, Window Vista, Window 7
•Web browser : Internet explorer 7.0 or higher, Firefox, Chrome, Safari
INTRODUCTION

Package Contents
6
This document contains confidential and proprietary information of Weldex Corporation.
INTRODUCTION
Package Contents
IP Camera –WDP-4602MXV
Installation CD
& Manual
Angle Regulators Screw
12VDC Power Supply with
Power Code (Optional)

Specifications
7
This document contains confidential and proprietary information of Weldex Corporation.
INTRODUCTION
Section WDP-4602MXV
Camera
Image Sensor Sony IMX122 1/3” 2Megapixel CMOS
Scanning System Progressive Scan
Lens F2.0 f=4.3mm Fixed Corn Lens
Electronic Shutter
Speed
Auto / Flk
NTSC : 1/30sec ~ 1/50,000sec,
PAL : 1/25sec ~ 1/50,000sec
White Balance AWB / MANUAL / INDOOR / OUTDOOR
Backlight
Compensation BLC / HLC / Off
ACCE Low / Middle / High / Off
AGC Low / Middle / High
Day & Night Auto / BW / Color
2D/3D-NR 2DNR / 3DNR / SMART NR
S/N Ratio More than 50dB
Min. Illumination 1.0Lux(Color) , 0.5Lux(BW) , 0.02Lux
(Sens-up x60)
Video
Compression H.264 @HP, MJPEG
Streaming
Simultaneous multiple streams
H.264 streaming over UDP,TCP,HTTP or HTTPS
MJPEG streaming over HTTP or HTTPS
Resolution 640x480, 800x480, 800x600, 1024x768,
1024x720, 1280x1024, 1920x1080
Frame Rate ⑵up to 30fps @1080p
Output NTSC/PAL 1Vp-p 75ohm composite
Specifications

Specifications
8
This document contains confidential and proprietary information of Weldex Corporation.
INTRODUCTION
Section WDP-4602MXV
Audio
Compression G.711 /AAC
Input Internal C-MIC (-30dB)
Output 1x Line Out
Networking
Interface 10/100 Mbps Ethernet, RJ-45
Protocols
IPv4, IPv6, TCP/IP, HTTP, HTTPS, UPnP,
RTP/RTSP, SMTP, FTP, DHCP, NTP, DNS, DDNS,
SNMP
ONVIF Version 2.0 Support
Users ¹ 8 Clients monitoring at the same time
Alarm and Event
Management
Motion Detection On / Off (12 Zone Selectable)
Sensor & Trigger out 1ch NO/NC input & 1ch active low output
Notifications Event notification using SMTP, FTP
Security Security
Multi-level user access with password protection,
IP address filtering,
HTTPS encrypted data transmission
Maintenance
Firmware Supports Firmware upgrade
Dual Booting Support for Firmware Recovery
Factory Reset Restores to factory default settings
Application Application SDK available for application development and
system integration

Specifications
9
This document contains confidential and proprietary information of Weldex Corporation.
INTRODUCTION
Section WDP-4602MXV
Power
Power Supply 9 VDC ~ 28 VDC Input
Power over Ethernet
(PoE) ² IEEE 802.3af
Power Consumption Max 5W
Housing Height-Strip Metal housing & Window acryl
Design Covert Design
Environmental
Operating
Temperature -10℃~ 60℃
Humidity 0 ~ 90% RH, non condensing
System
Operating System Embedded Linux
Dimensions 47mm(W) x 29mm(D) x 869mm(H)
Weight 800 g
Note
(1) Number of simultaneous connections will be reduced if 1080p@30fps is used.
(2) If PoE and external power are connected at the same time, external power will be used. If
external power is removed, it will switch to PoE and vice-versa. The camera might reboot
during power switching.

Hardware Overview (Appearance)
Hardware Overview
10
This document contains confidential and proprietary information of Weldex Corporation.
INSTALLATION
INSTALLATION
Item Description
①
Height-Strip cover : Acryl
Height
-Strip cover for the lens and unit protection.
②
Factory reset switch
Press and hold this button for 5 seconds while the unit is turned
on.
-
System LED should be turned ON when performing factory reset.
-
The LED next to the switch will flash 3 times after a successful
reset.
③
C-MIC connector
Used for microphone
input
④
Main body Set
Main body chassis
⑤
Ethernet port
Network
port
⑥
Sensor-in/Alarm-out port
Used for s
ensor input & alarm output
⑦
Audio-out port
Use this port to output audio to speakers
⑧
Video-out port ⑴
Composite Video Output
⑨
Power-in port
Power input port (not needed if
PoE is being used)
Note (1) Video output connector is used only for installation purposes. It should not be used for
recording or surveillance purposes.

Disassembling
11
This document contains confidential and proprietary information of Weldex Corporation.
INSTALLATION
Disassembling
1. Using the screw driver, loosen 4 screws by
turning top plate counterclockwise and
remove the window acryl cover.
2. Using the screw driver, loosen 4 screws by
turning them counterclockwise for Main
board.
3. Using the screw driver, loosen 4 screws by
turning them counterclockwise for Camera
board.
4. Disassemble the IP main harness cables.
Precautions before installation
Ensure you read out the following instructions before installing the camera:
•Select an installation site (wall) that can endure at least 5 times of the camera weight.
•Stuck-in or peeled-off cables can cause damage to the product or a fire.
•For safety purposes, keep anyone else away from the installation site. And put aside personal
belongings from the site, just in case.

Installing the camera on a wall
Installing the camera on a wall
12
This document contains confidential and proprietary information of Weldex Corporation.
INSTALLATION
1. Assemble the Angle Regulator parts (supplied) to the rear surface.
2. Fix the case body on the wall by using Tapping Screws (BHT M4xL16).
3. Connect ethernet and accessory cables and arrange cable running not to damage or squeeze them.
4. Pass the ethernet and power accessory cables through the hole you want to pass them when
mounting the main body on the case.
5. Assemble the Height-Strip Cover [Window Acryl].
6. Fasten 4 screws by turning top plate clockwise.
M4 tapping screw x 2(supplied)

PCB Board Layout of the Camera
CMOS Board layout of the camera
13
This document contains confidential and proprietary information of Weldex Corporation.
INSTALLATION
MAIN Board layout of the camera
Location Number Description
CN1
FPC/FFC 30pin Cable to connect the CMOS Board
SW1
Factory Reset switch
D19
Factory Reset indicator
D14
Power Indicator
D18/D7
Ethernet Link / Activity indicator
JP1
Power/Video out/Audio out/Sensor in/Alarm out signals
JP2
Ethernet/Power over Ethernet signals
Location Number Description
U1
CMOS Sensor device
CN3
FPC/FFC 30pin Cable

Connection sensor input and alarm output
Connection - sensor input
Connect the sensor’s NO or NC wire to the blue wire of the accessory cable.
Connect the sensor’s GND to the black wire of the accessory cable.
14
This document contains confidential and proprietary information of Weldex Corporation.
INSTALLATION
Connection - alarm output
Connect the alarm device’s GND wire to the green wire of the accessory cable.
Connect the accessory cable’s black wire to the GND of the power supply where the device is connected
to.
Only DC alarm device are supported. If alarm devices 2A or higher are used, an external relay is
required.
Resistor
Photo Coupler
12 43
+3.3V
Resistor
+3.3V
Capacitor
Sensor
Camera
Black wire
Blue wire
NO or NC
GND
Power FET
GND
Black wire
Green wire
Camera
Alarm device
(+)
(-)
DC Power
Supply

Dimension
15
This document contains confidential and proprietary information of Weldex Corporation.
INSTALLATION
Dimensions

Network Initial Setup
Network Initial Setup
This section describes how to initially set up your Weldex network camera. Initial setup consists of the
following series of steps:
Locating the unit on the network
Changing the network settings
Initial setup of the unit requires a computer connected to the same network as the unit(s). Each
Weldex network camera is shipped with the following factory default connection settings:
16
This document contains confidential and proprietary information of Weldex Corporation.
NETWORK INSTALLATION & SETUP
NETWORK INSTALLATION & SETUP
Note (1) If the Network Camera is not able to obtain an IP address from a DHCP server, it will
automatically switch to the following static IP settings:
-IP address : 192.168.0.200
-Subnet mask : 255.255.255.0
-Gateway address : 192.168.0.1
Setting Value
IP
address ⑴
DHCP
IP
subnet mask ⑴
DHCP
IP
gateway address ⑴
DHCP
Administrator Login ID
admin
Password
9999
The following Transmission Control Protocol (TCP) ports must be open on the network:
80 (web based configuration port)
554~558 (RTSP video delivery port)
Once you have initially set up your unit, you are ready to configure the rest of the unit’s settings.

IP Scan Tool
IP Scan Tool
After physically connecting the network camera to the network, run the ‘IPScan.exe’ application on
the software CD. This program will scan for Weldex cameras on the network, regardless of the unit’s IP
address. Once you locate a unit, you may change the network settings
17
This document contains confidential and proprietary information of Weldex Corporation.
NETWORK INSTALLATION & SETUP
Note Verify that the computer where you will run the ‘IPScan.exe’ file is on the same network as the
unit you wish to locate. Units on a different network will not appear when running the search
function.
IP Scan Tool Functions
Item Functions
①
Search
Searches for the connected Weldex
network camera.
②
IP Setup
View/Edit IP settings for the
selected
Network Camera (Device ID, IP
address, Subnet mask and Gateway).
Administrator’s password is required.
③
Web Browser
Connects to the
selected Network Camera using the default web-
browser.
④
Device Info
Displays device info for the
selected Network Camera.
⑤
Factory Default
Restores factory defaults for the
selected Network Camera
Administrator’s password is required.
①②③④⑤
⑥⑦⑧⑨⑩

IP Scan Tool
18
This document contains confidential and proprietary information of Weldex Corporation.
NETWORK INSTALLATION & SETUP
Configuring Network Settings Using IP Scan Tool
Run ‘IPScan.exe’executable file and click [Search]. Network connected Weldex cameras will be listed
in the window.
Item Function
⑥
Device ID
Displays device ID of the camera.
⑦
IP Address
Displays
IP address of the camera.
⑧
MAC Address
Displays
MAC address of the camera.
⑨
Model Name
Displays
model number of the camera.
⑩
Firmware Version
Displays firmware version of the camera.
1. Select the camera to be configured by
clicking on your mouse.
2. Click on the [IP Setup] button to
access the IP setup window for the
selected camera.
3. You will be prompted to enter the
admin’s password
4. Make the desired changes to the IP
settings and click [Setup] to save
changes.
Note MAC Address cannot be changed
Note Default admin password is
[admin]

VLC Player Installation
VLC Player Installation using the executable file (recommended)
VLC Player installation is required to view live image and control the network camera on a web-
browser.
19
This document contains confidential and proprietary information of Weldex Corporation.
WEB Viewer
WEB Viewer
1. Install the ‘vlc-2.0.6-win32-
weldex.exe’ executable file from the
installation CD.
2. Previous installations of VLC player
should be uninstalled.
3. Start the installation process.
4. From the [Select the type of install]
dropdown menu, choose [custom].
5. Confirm the installation path and click
[Next] to start copying files to the PC.
Note Previous installations of VLC Player should be completely uninstalled from the PC. Weldex uses
a customized and proprietary version of VLC Player which requires that all other VLC versions
be removed from the PC, even if the installed version is newer than what’s provided by Weldex.

VLC Player Installation
20
This document contains confidential and proprietary information of Weldex Corporation.
WEB Viewer
6. Uncheck the [Run VLC media player
2.0.6] checkbox
7. Click on the [Finish] button to complete
the installation.
VLC Player Installation through the ActiveX Control (Internet Explorer Only)
1. Using your IE browser, type in the
camera’s IP address in the URL address
bar.
2. After a successful connection, you will
be prompted to install the ActiveX.
3. When prompted to install [Weldex VLC
ActiveX Control], click on the [Install]
button to start the installation.
4. When prompted to install ‘Weldex VLC
Control’, click on the [Install] button to
start installation.
5. Choose the desired language.
6. Follow the steps “VLC Player
Installation” of this manual for the rest
of VLC Player installation.
7. After a successful installation, refresh
the page and confirm that the image
appears properly.
8. For newer version of IE (IE9, IE10), the
‘Compatibility View’ might need to be
enabled for the WEB Viewer to display
properly.
9. For IE11, the IP address of the camera
should be added to the Compatibility
View Settings (Tools>Compatibility
View Settings)