WESTBRASS KH41A User manual

USER MANUAL 1 2
AB
N
M
L
P
O
H
Q
I
R
J
K
C
D
E
F
G
NO. Description QTY
A Faucet 1
B Spray Head 1
C Counter Weight 1
D O-ring 1
E Rubber Washer 1
F Metal Washer 1
G Mounting Nut 1
H Boiled water Supply Hose 1 1
I Boiled water Supply Hoes 2 1
J Drinking Water Supply Hose 1
K Cross Fitting 1
L Wall Mount with screw 1
M
NOutlet Hose
Stem 1
O Boiling water outlet hose 1
P Drinking water outlet hose 1
Q Hot & cold supply lines 1
R Pull-down hose 1
1
1. Insert the 0-ring (D) over the hoses
into faucet shank, and mount the
faucet on the basin See Fig.1
3. Use a Phillips head screwdriver to tighten the 2 screws. Do not over tighten.
2. First slide the rubber gasket
(E), then the metal washer (F)
and the mounting nut (G) over
the hoses onto the stem (N).
Hand tighten them firmly. See
Fig.2
3
O-ring
Insert
O-ring
4-1 Instant Hot Water and Drink Water Faucet
Please note: Pass the 3
hoses with nuts FIRST and
then pass 3 tubes without
nuts to facilitate installation.
2
4
3
5
6
7
8
9
1
1-3/8” Diameter
Hole
Fine Decorative Plumbing Since 1935
WESTBRASS
WESTBRASS s%/LYMPIC"LVD,OS!NGELES#!
ssORDERS WESTBRASSCOMsWWWWESTBRASSCOM
KH41A

1
1
4M
K
4. Connect the Cross fitting (K) to the Outlet Hose
M (Hose ①/ White Color) , and hand tighten onto
the cross fitting. Use the mounting bracket to fix the
cross fitting against the back wall. See Fig.4
5. Remove the release ring retainers from the filter and save.
Fit water Drinking water outlet hose (P) (label ②/ Blue Color)
into the filter housing inlet. Fit Drinking Water Supply hose (J)
(with label ③/ Green Color) into the filter housing outlet, and
attach the another end of the hose to the left (or right) adapter of
Cross fitting (K). Mount fitting on wall and assemble according
to instructions inside the filter box. See Fig.5
8. Attach the pull-down hose (R) (with label ⑦/ White
Color) to the adapter at the bottom of the Cross fitting
(K). Install the counterweight (C) on the pull-down
hose at the marked position. It should be placed on
the pull out spray hose. See Fig.8
10. Tidy up all the hoses, so they don't get
tangled up. Please leave enough space for the
pull-down hose with counter-weight to move up
and down without interference, to ensure the
integrity of the pull down function.
6. Remove the release ring retainers from the filter and save.
Fit boiling water outlet hose (O) (label ④/ Blue Color) into
the filter housing inlet. Fit boiling water supply hose (H) (label
⑤/ Green Color) into the filter housing outlet, using the
washer under the cap. Connect the other end of the hose (H)
onto the inlet of the hot water tank, indicated with blue.
Secure the connection with an adjustable wrench. Replace
retainer rings. Mount filter according to instructions included
in the filter box. See Fig.6
7. Connect boiling water supply hose 2 (I) ( with label
⑥/ Red Color) onto the outlet of boiling water in the
center of the tank. Indicated with red. Make sure to
use the washer under the cap, then tighten with an
adjustable wrench to secure the connection. Connect
the other end of the hose (I) to the cross fitting
adapter (K) until it snaps in place. See Fig.7
9. Remove the Hand Spray from the faucet. Connect the hot
water line (label ⑨/ Red Tracer) & cold water line (label ⑧/
Blue Tracer) onto the matching 3/8 in. compression water
valves. Secure the connection with an adjustable wrench.
Tum on the water supply and check the water connections for
leaks. Purge the system and fill the hot water tank by
operating the hot water handle until several gallons runs out
of the faucet. Purge hot and cold dishwater. Purge pure water
faucet. See Fig.9
K
33
7
2
5
J
PK
8
10 11
R
C
weight location label
9Q
6
7
4
O
HI
5
8
9
KK
6
HC
3
2
4
5
6
1
7
8
9
Hot Cold
Pull handle knob and rotate the handle forward 45
degrees to turn on the Instant Hot. Water will come
out of the faucet after 2-3 seconds.
Caution: Water is Scalding Hot!
11. Now, plug tank into electrical outlet. Press and hold
the start button for 3 seconds to switch unit on. Power
indicator will flash and show temperature. Follow the
instructions included with the tank to adjust temperature.
Caution
Scalding!