WESTERN PROCESS FP-3018B User manual

MODEL FP-3018B
Flat Panel Display
User Manual
Revision 6

2
Introduction
The FP-3018B is an LED-Backlit flat panel display module designed to be a drop-in
replacement for the Honeywell Universal Station Sony Flat Screen CRT-type display utilizing
the EPDG video system.
The FP-3018B utilizes the existing openings in the front bezel of the US to control display
settings such as brightness and contrast.
Installation is easy. The FP-3018B is ready to mount to the existing bezel. A power cord with
a twist-lock plug is provided. The video connector is the standard 15-pin connector. A 15-pin
to 9-pin adapter is provided to allow connection to the 9-pin ribbon cable video source utilized
in some Universal Stations. Use your existing video controls bracket with the provided adapter
box. See below for more details.
Contents of the Box
1. Main monitor unit with Menu adapter and Bezel Mounting Brackets attached.
2. Fastening Hardware for mounting monitor into Bezel.
3. 9-pin to 15-pin video adapter plug.
4. Power cord with 125VAC 15A twist-lock plug.
5. This User Manual.
Installation
1. Power down the station
2. Remove the existing bezel keeping cables intact to reconnect to FP-3018B. The video
connector is the standard 15-pin connector. A 15-pin to 9-pin adapter has been installed
on the back of the display to allow connection to the 9-pin ribbon cable video source
utilized in some Universal Stations.
3. Using your existing video controls bracket, plug your existing connector into the
matching connector on the adapter box.
4. Plug the adapter box into the back of the FP-3018B (if not already done)
5. To provide for proper chassis grounding, a green ground screw is provided near the
lower left corner on the back of the FP-3018B.

3
6. Ensure that the power cord is connected to appropriate power supply using provided
twist lock plug.
7. Power up the station. (Your video controls should operate as you are used to).
Setup
The FP-3018B has been set up at the factory. These factory settings will yield a close to
perfect display for a typical US with EPDG video. The horizontal position and the phase
adjustments may have to be slightly adjusted for your particular US. The brightness, contrast
and black level values can be adjusted for your particular environment and preference. See
Page 4 for more detail.
A is a 6-button menu: The green button acts as the MENU or Back button when pushed. The
Up and Down arrows both act as the NEXT function. The Left and Right arrows move through
sub-categories as well as decrease or increase the values of the sub-category. The plus sign
with arrows at the top of this menu is not used.
B is a 3-button menu: The green button acts as the MENU or Back button when pushed. The
Right and Left arrows must be pushed simultaneously to achieve the NEXT function in the
main menu as well as in sub-categories. When in a sub-category if they are pushed one at a
time they move through sub-categories as well as increase (Right Arrow) and decrease (Left
Arrow) values of the sub-category.
C is a 5-button menu: The green button acts as the MENU button when pushed. The Up and
Down arrows act as a NEXT function. The Minus (-) symbol and Plus (+) symbol are to move
through sub-categories as well as decrease or increase the values of the sub-category.
A B C
A
B
C

4
NOTE: Factory Setting for Timeout Delay has been set at “0” which forces you to explicitly exit
out of the OSD. (Timeout delay time can be changed in the setup mode in the “SYSTEM/ OSD
Configuration”, however if this is done, you must remember to fully exit out of the OSD in order
to save your changed setting)
FINE-TUNING:
IMAGE / Brightness: Adjust to provide adequate brightness for your ambient light level.
IMAGE / Black Level: Adjust as high as possible without getting background glow or noise.
IMAGE / Contrast: Adjust for your particular preference.
DISPLAY / Phase: Adjust if picture is out of focus, dim or spotty.
DISPLAY / CLOCK: If not set properly, the display will exhibit out of focus vertical columns.
Adjust the clock value until the number of these columns is reduced to zero.
(Leave at 146 for EPDG)
DISPLAY/DISPLAY CONTROL/DISPLAY POSITION: HORIZONTAL: Adjust Horizontal
Position so the image is not chopped off on either side. (Set at 166)
DISPLAY/DISPLAY CONTROL/DISPLAY POSITION: VERTICAL: Adjust Vertical Position so
the image is not chopped off at top or bottom. (Set at 255)

T
T
a
T
o

A
ssu

A
ssu
Do n
o
unex
Unpl
u
Do n
o
Do n
o
Do n
o
Do n
o
Dam
a
If an
y
o
o
o
o
o
T
he FP-30
1
T
his facepl
a
a
brasive lin
T
he FP-30
1
o
peration.
re sufficient
re ambient
a
o
t attempt t
o
pected failu
r
u
g the moni
t
o
t put metal
o
t use this
m
o
t subject t
h
o
t place he
a
a
ge could c
a
y
of the follo
w
Power su
Liquid ge
t
The moni
The moni
The moni
1
8B requir
e
a
te has an
t-free cloth
1
8B is warr
a
P
space is av
a
ir temperat
o
disassem
b
r
e and will v
o
t
or from the
objects in v
m
onitor in a
p
h
e monitor t
o
a
vy objects
o
a
use electri
c
w
ing conditi
o
pply, cord a
t
s spilled on
tor does no
t
tor has bee
n
tor display
e
e
s no maint
e
anti-glare
c
.
a
nted for a
P
roduct S
a
ailable arou
u
re does no
b
le, repair or
o
id the warr
a
wall before
ents. Electri
p
lace whe
r
e
o
direct sunli
o
n the powe
r
c
al shock
o
ns exist, u
n
nd/or plug
a
or into the
m
t
operate no
n
dropped o
e
xhibits cha
n
Mai
e
nance ot
h
c
oating, so
W
period of t
w
5
a
fety Prec
a
nd the moni
t exceed th
e
modify the
p
a
nty
repositionin
g
cal shock c
o
water intru
s
ght or heat
r
supply or
p
n
plug the p
o
a
re damage
d
m
onitor or t
h
rmally whe
n
r the frame
e
n
ges in perf
o
ntenanc
e
h
er than pe
r
use only a
W
arranty
w
o years a
g
a
utions
tor to provi
d
e
specified
m
product.
A
n
y
g
to protect
f
o
uld occu
r
s
ion could o
c
p
ower cords
o
wer supply
f
d
;
h
e monitor i
s
n
the User
M
e
nclosure d
a
o
rmance, in
d
e
r
iodic clea
n
residue-fr
e
gainst failu
d
e adequate
m
aximum te
m
y
attempt to
from possib
c
cu
r
.
from the wa
s
exposed t
o
M
anual instr
u
a
maged;
d
icating a n
e
n
ing of the
g
e
e glass cl
e
re in the c
o
circulation
m
perature
do so may
c
le electrical
ll or monito
r
o
rain or wat
e
u
ctions are f
o
e
ed for servi
g
lass face
p
e
aner with
a
o
urse of no
r
c
ause
shock
r
:
er
;
o
llowed;
ce.
p
late.
a
non-
r
mal