Westinghouse VR-3225 User manual

10
11
11
10
9
9
12
Power Cord Connection
AV Connection
YPbPr(component) Connection
VGA(PC) Connection
Antenna Connection
HDMI Connection
Service Port Function
2
4
5
1
5
26
Remote control instructions in TV mode
Remote control setup 14
13
17
18
24
22
20
19
19
TABLE OF CONTENTS
English
4
1
6
7
8
5
9
10
I M P O R TA N T
INFORMATION
2HOW TO INSTALL
THE STAND
3PREFACE
TROUBLESHOOTING
SAFETY
PRECAUTIONS
FRONT/BACK
CONNECTIONS
OF LCD TV
REMOTE CONTROL
TV INSTALLATION
CONTENTS
MENU OPERATION
7
8
Operating the Menu
PICTURE Menu
AUDIO Menu
TIME Menu
SETUP Menu
LOCK Menu
CHANNEL Menu
SETUP WIZARD 15

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of un-insulated dangerous voltage within the products
enclosure that may be of sufficient magnitude to constitute a risk of electric to persons.
The exclamation point within an equilateral triangle is interded to aler the user to the
presence of important operating and maintenance (servicing) instruction the literature
accompanying the appliance.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock, do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
Refer to service manual for servicing instructions.
Important Safety Instructions
Note:
1.Read these instructions.
2.Keep these instructions.
3.Heed all warnings.
4.Follow all instructions.
5.Do not use near water.
6.Clean only with dry cloth.
7.Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
2
IMPORTANT INFORMATION
English

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11.Only use attachments / accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over.
13.Unplug this apparatus during lightning storms or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15.Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, suchas vases, shall be
placed on the apparatus.
16.WARNING:To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
17.Mains plug or appliance coupler is used as the disconnect device, shall be readily operable.
3
IMPORTANT INFORMATION
English
18.The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.

HOW TO INSTALL THE STAND
English
4
Fixed-ring base
Rotating base fixed plate
Screw holes
Base cover
Limit
Hole spacing
Screws
Fix the base cover to the fixed-ring
base as image 1.
Assembly two small parts in image2
at the bottom of the Base Cover and
fix with 6 screws in the Screw Hole.

5
3. PREFACE
Thank you for buying this Please read this manual thoroughly before operating the TV.
Make sure the TV was not damaged in transit. Should the TV be damaged, do not install it and
contact your dealer. Check that you have all the accessories according to the model.
TV!
4. SAFETY PRECAUTIONS
Power cord and cables must be properly routed and protected to prevent
people from stepping on them and causing the TV to fall.
Minimum distances
10cm
20cm
10cm 5cm
Put the TV on a stable surface.
Do not place any material on the TV.
Do not block or cover the ventilation openings on the TV.
If you have a wall mount, check that it is steady.
Do not use the TV with fixtures other than those provided or
suggested by the manufacturer.
English
PREFACE

6
Keep the TV dry and away from humidity.
Keep the TV away from heat sources.
Unplug the TV before cleaning it. Do not use solvent or liquid to clean
the TV.
Only clean the TV with a soft and dry cloth.
In case of troubleshooting, do not use spare parts other than those
suggested by the manufacturer. Using inadequate spare parts can
lead to electric shocks, short-circuits, fire or other incidents.
Unplug the TV during lightning storms or when unused for long periods
of time.
English
SAFETY PRECAUTIONS

7
5. CONTENTS
Remote Control
1.5V
1.5V
AAA Batteries
LCD TV SET
Power Cable
USER'S MANUAL
English
CONTENTS
Quick Connect Guide
Quick Connect Guide
Warranty Card
Warranty Card

Front View
6. FRONT/BACK CONNECTIONS OF LCD TV
Back View and Control Connections
19
58
2
2. Press“SOURCE”to select the input source.
3. Press “MENU”to bring up the main menu on
the screen.
4. Press“CH+”or “CH-”to scan through channels.
5. Press“VOL+”or “VOL-”to increase or decrease
the volume.
6. POWER INDICATOR: red in standby mode.
red or green when your TV is switched on.
7. REMOTE SENSOR: infrared sensor for the
remote control.
Shows
Shows
SOURCESOURCE
MENUMENU
CH-CH-
CH+CH+
VOL-VOL-
VOL+VOL+
POWERPOWER 1
2
3
4
5
6
7
English
FRONT/BACK CONNECTIONS OF LCD TV
34
8
10
7
6
1. Press“POWER” button to turn the TV on or off.
1.AC IN: Main power input.
2.USB Service: USB port for Factory Use Only.
3.HDMI1 / HDMI2: Connect to the HDMI output jack
of a DVD player.
4.VGA (PC): Connect to the VGA RGB output jack
of a PC.
5.PC AUDIO: Connect to the Audio output jack of a PC.
6.COMPONENT: Connect to the YPbPr output jack
of a DVD or VCR player.
7. AV: Connect to the Video output jack of a DVD or
VCR player.
8.AUDIO IN: Connect to the Audio output jack of a
DVD or VCR player.
9.RF IN: Connect to an antenna or cable source.
10.HEADPHONE: Connect to a headphone.
AC IN