WFCO ULTRA WF-8914 User manual

lnstallationlOperatorsManual
For usewith WFCO
ULTRA DistributionPanels
ModelWF-8914
Distributed inthe US by CHENG USA, Inc.
Sales [phone]
Warranty Service [phone]

Mounting:
Selectthe mounting locationand cut a rough opening 118" wider than the box to
allow the Distributionpanel to slide in easily. The hole shouldbe framed so that
the
box can be secured tightly.
TheOEM may wish to pre-wire the box for easeof installation. Selectthe
numberof lcnockouts to be used and removethem. Two sizeshave been
provided.The 1118" isfor the 30 amppower cord. The 718" hales are for the
romexon the l2OVAC side and the wires on the 12VDCside. Remember to select
the proper gauge wire for the load and distance. Leave the rest of
the knock-
@
outs in place. Be sure to use appropriateRomex connectorsand strain reliefs to
securethe wiresto the box. (see wiring diagram)
GeneralInformation:
AC Bus Bar Max. Rating is
33.4 Amps
Quick connects:
Thenonmetalicsheathconnector is foruse with wire rangesof 10-2
thru 14-2 only.
1.For use with cu wiring only.
2.Use
K.S. TerminalsInc. Model FDD2-250 femalequick connectonly
3. Use Id #34 (blue) as the crimpingtool
4. The end-use manufactureris to provide strainrelief
and instructionson how to use it
5. The striplength is 6.5 mm
For Field WigAluminumTerminals TheTighteningTorque Max. 40 in-lb.
TemperatureRating is 90QC.
Fusesand breakers:
Breakers
1. The 30 Amp ULTUDistributionpanel was designed for a 30 AMP main haker
with branch circuits. Doublebreakers may be used forthe branch circuits. Should
a breaker become faulty replace with the same type breaker asprovided by the
OEM.
2. AC Breaker Information:
AC Breaker Specification:MAX.30Amps 120Vl240V 1pole or poles.
CurrentInterruptingRating
MAX.RMS SYM.Arnperes 10,000AT 1201240
VOLTS AC
3. ACBreaker Manufacture:
1:"Cutler-Hammer": Type BRD &A
2:"SIEMENS": Type QP OR QT
12 VDC Fuw
Each circuit in the WFCO ULTRA Distributionpanel was designed for a maximum
of a 20 amp Little Type 257 automotivestylehe.Should one need to be
replacedbe sure to replace it
with the sametype and amp rating as originally
suppliedby the OEM. Replacing it with either a higher or lower amp fuse could
result
in the panel not functioningproperly.
Fuse Diagram:
Max. Main Circuit Fuse Size: 30
AMP
Max. BranchCircuit Breaker Fuse Size:20 AMP
12 VDC Fuse use Only Littelfuse. Type 257Fuse. Max. 20 AMP
Each 12VDCcircuit of the WFCO ULTRA Distributionpanel is provided ~4th a LED
indicatorlight. Shouldthe fbse"blownor an open be
caused the LEDwill lightup
indicatingwhich circuit is open and which fuse needs to
be replaced.

TOP VIEW
REAR VIEW
BOTTOM VIEW

FRONT VIEW
t J
LITTLE M)OR--l

Consumer Limited Warranty
For
WFCO Electronic Products
WFCO extends, to the original owner a two year Limited Product Warranty. This
Warranty is in effect from the date of original purchase for a period of two
(2) years. This
Limited Warranty is extended specifically for and is limited to recreational vehicle
application and is only valid within the continental United States,Alaska, Hawaii and the
provinces of Canada. WFCO warrants, to the owner, that it's products are free from
defects in material and workmanship under normal use and service based on its intended
use and function. This Warranty is limited to the repair or replacement, at WFCO' s
discretion, of any defective parts or defective assembly.Any implied warranties of
merchantability or fitness for intended use are limited in duration unless applicable State
Law provides otherwise. You may have other rights as specified by each individual state.
EXLUSIONS and LIMITATION
The OEM warranty specifically does not apply to the following:
Any WFCO product that has been repaired or altered by any unauthorized person;
Any damage caused by misuse, faulty installation, testing, negligence or accident or any
WFCO product installed in a commercial vehicle;
Any WFCO product whose serial number has been defaced, altered or removed;
Any WFCO product whose installation has not been in accordance to WFCO written
instructions;
Any consequential damages arising from the loss of use of the product including but not
limited to: inconvenience, loss of service, loss of revenue, loss or damage to personal
property and cost of all services performed in removing or replacing the WFCO product;
CONSUMERWARRANTY CLAIM PROCEDURE
Upon determination and validation by an authorized OEM dealer that a WFCO product
has a defect, the dealer shall contact the WFCO warranty service number
[phone]
and obtain a return goods authorization (RGA) number. This number shall appear on all
correspondence with warranty service, Upon validation of the warranty WFCO shall
replace or repair the product with a like product.The
RGA number must also be placed
on the outside of the carton used to return the product for ease of identification.Do not
mark directly on the product. The product must be package in properly to avoid further
damage to the product to cause a non-warrantable condition.