Wharfedale Pro L15T11W-A, L15T11W-C, L19T11W- User manual

USER'S MANUAL
HD Ready Digital LCD TV
Please read thismanual carefully before
using your televisionand keep thismanual
In a goodplace for futurereference.
MODEL:
L15T11W-A, L15T11W-C,L19T11W-A,
L19T11W-C, L20T11W-A,L20T11W-C,
L19T12W-A, L19T12W-C, L20T12W-A,
L20T12W-C,L22T11W-A,L22T11W-C

CONTENT
Safety Notice ............................................................................................
Front Panel Control...................................................................................
Connection ..............................................................................................
Remote Control ........................................................................................
Remote Control ......................................................................................
Installing Batteries..................................................................................
Connection Instructions.............................................................................
Grounding..............................................................................................
External equipment connections..............................................................
Antenna Connection.............................................................................
VGA Input.............................................................................................
YPbPr Input...........................................................................................
S-VIDEO Input....................................................................................
SCART Input.......................................................................................
HDMI Input.........................................................................................
Basic Operating Instructions.......................................................................
Turn on the LCD-TV.................................................................................
Audio Control..........................................................................................
Mute......................................................................................................
Select the TV Channel ............................................................................
Picture Mode...........................................................................................
Program Swap.........................................................................................
Program Scan.........................................................................................
Menu Operations.......................................................................................
Picture Menu Options...............................................................................
Audio Menu Options................................................................................
Function Menu Options.............................................................................
Adjust Menu Options................................................................................
Tuning Menu Options..............................................................................
DVB-T Main Menu Operations....................................................................
Channel List...........................................................................................
Favourite List..........................................................................................
Now/Next EPG........................................................................................
Timers....................................................................................................
Settings..................................................................................................
TELE TEXT...............................................................................................
Basic Playback..........................................................................................
Advanced Playback...................................................................................
Special Function Playback.........................................................................
JPEG DISC PLAYBACK............................................................................
SCREEN SAVER FUNCTION....................................................................
DVD System SETUP...................................................................................
General Setup Process.............................................................................
General Setup Page...................................................................................
Preferencel Page.....................................................................................
Playable Discs..........................................................................................
Disc Protection and DVD Characteristics.....................................................
Troubleshooting Guide...............................................................................
Specifications...........................................................................................
1
2
3
4-5
6
6
7
7
7
7
8
8
9
10
10
11
11
11
11
12
12
12
12
13
13
14
16
18
19
21
21
22
22
23
23
26
28
29
30
30
30
31
31
31
33
35
36
37
38
Note: DVD instructionin this manualis just for the special models which have the DVD slot.
(DVD is onlyavailable in somemodels, please see the real)

Safety Notice
To prevent fire or electric shocks please read the instruction before
installing, using and cleaning the television.
lPlease read all the instructions before operation;
lPlease keep themanual for future reference ;
lDo not use any accessories that not recommended by manufacturer:
lBefore operation, make sure the operating voltage of this unit is corresponds
with your houseelectricting supply;
lDo not placethe unit on unstable, dusty andhumid places;
lNever put theunit in direct sunlight or nearheat sources;
lAllow enough space for proper ventilation;
lPlease keep water away from the LCD-TV . If water comes in contact with the
LCD-TV, disconnect the power cord from the power source, then wipe the set
with a dry soft cloth;
lDo not removethe back cover. If services were need,please refer to
customer helpline.
Customer helpline:0845 604 0105

Front Panel Controls
Control Panel Function
1. Standby switch
2.SOURCE Select the input signals: PC/COMPONENT/DVD/HDMI/
TV/SCART/S-VIDEO
3. MENU Press to select the main menu
4. VOL- Volume down/ Left orientation to adjustthe item in the OSD
VOL+ Volume up / Right orientation to adjust the item/Press to enter
5. CH- TV channel down / to select the item in the menu
CH+ TV channel up / to select the item in the menu
6. Power indicator
Illuminates red in standby mode, illuminates green when the display is
turned on
7.Remote Sensor
6
7
L15T11W-A, L15T11W-C,
L19T11W-A, L19T11W-C,
L20T11W-A,L20T11W-C,
L22T11W-A,L22T11W-C
SOURCE MENU VOL- VOL+ CH- CH+ POWER
23451
6
7
L19T12W-A,L19T12W-C,
L20T12W-A,L20T12W-C,
SOURCE MENU VOL- VOL+ CH- CH+ STANDBY
Or
(The description ofthe button maybe different, justsee the real.)
Customer helpline:0845 604 0105

Connection Options
COMPONENT Input
Connect a component
video/audio
device to thesejacks
VGA Input
Connect to theVGA
15PIN analog output
connector of thePC
display card forPC
display purpose
S-Video Input
Connect S-Video out
from an S-Video device
to the jacks.
Antenna Input
Connect cable or
antenna signals to
the TV, either direc-
tly or through your
cable box.
Earphone port
VGA /COMPONENT/
SVIDEO Audio Input
Connect the PC output
connector from aPC to
the audio inputport
SCART
Connect to the DVD/
VCR/broadcasting
receiver or other
equipment
ANT IN Y
Pr S-VIDEO TV SCART VGA IN
AUDIO IN Pb HDMI
HDMI
Connect to HDMI
output of other
equipment
ANT IN Y
Pr S-VIDEO TV SCART VGA IN
AUDIO IN Pb HDMI
The above figure is for reference only,
connections may differ depending upon
the models
DVD
STOP PLAY/PAUSE OPEN/CLOSE
PREV NEXT
DVD insert
Please see thereal set ofthe
DVD position
Customer helpline:0845 604 0105

Remote Control Key Functions(for TV/DVD Combi)
When using the remote control, aim it
towards the remotesensor on the TV
Stand By
DVD Open/close
Picture Mode
Scan
DVD 10+
Mute
Swap
Call Screen Display
Program Number
NICAM
Source Exchange
Digital Selector
DTV/DVD
Volume/Channel Selection
MENU
Zoom
DVD Audio
DVD STOP
Tune Menu Button
DVD SETUP
DVD PAUSE/STEP
DVD FAST REVERSE
DVD FAST FORWARD
DVD/DVB-T MENU
DVD NEXT
DVD PREVIOUS
Exit Screen Display
DVD PLAY/ENTER/DVB-T ok button
DVD PROGRAM/ DVB-T EPG button
DVD /DVB-T Cursor Move button
DVD /DVB-T SUBTITLE
DVD ANGLE/ DVB-T favourite
DVD SEARCH
DVD A-B REPEAT
DVD TITLE/PBC/DVB-T information button
DVD SLOW
DVD CALL
TELETEXT BUTTONS
DVD REPEAT
RED button
Green button
Yellow button
Blue button
Buttons on the remote control
UP
DOWN
LEFT RIGHT
STANDBY OPEN/CLOSE
SCAN SWAP CALL MUTE
1234
5678
9900-/---/--
SOURCE
DTV/DVD
P+
P-
V- V+
MENU
ZOOM AUDIO
STOP SETUP PAUSE/STEP
REV FWD .PREV NEXT
D.MENU EXIT PROGRAM
PLAY/ENTER SUBTITLE
ANGLE TITLE/PBC SEARCH
SLOW D.CALL
10+
A-B
TUNE
NICAM
P.STD
EPG
OK
FAV i
REPEAT
SIZE TIME
REVEAL MODE
MIX TEXT
SUBCODE HOLD
(For TV/DVD CombiModels)
Fast text buttonin analog
signal
Function button inDVBT
(just reference theOSD)
Customer helpline:0845 604 0105

Remote Control Key Functions(for TV only)
When using the remote control, aim it
towards the remotesensor on the TV Buttons on the remote control
Stand By
NICAM
Picture Mode
Switch to PC mode
Return the last watched program channel
Mute
Automatically adjust in PC mode
Call Screen Display
Program Number
Picture mode
Source Exchange
Digital Selector
DTV/TV
Volume/Channel Selection
MENU
Sound mode
Zoom
TELETEXT BUTTONS
DVB-T MENU
TEXT BUTTON
DVB-T EPG button
DVB-T ok button
DVB-T SUBTITLE
DVB-T Cursor Move button
DVB-T favourite
Exit Screen Display
DVB-T information button
RED button
Green button
Blue button
Yellow button
UP
DOWN
LEFT RIGHT
STANDBY NICAM
PC AUTO AD DISPLAY MUTE
1234
5678
90-/---/--
SOURCE
DTV/TV
P+
P-
V- V+
MENU
S SM ZOOM
SUBCODE MIX MODE
REVEAL SIZE TIME INDEX
D.MENU TEXT EPG
SUBTITLE
FAV INFO EXIT
HOLD
P.STD
SLEEP
OK
i
Q.VIEW
(For TV Models)
Note:
The instructions onthis manual is just
take remote controlforTV/DVD Combi
for example.
Customer helpline:0845 604 0105

Remote Control Key Functions
Installing Batteries
3
2
1
1.Open the coverof the battery compartment at the back of the remote
control.
2.Insert twoAA alkaline batteries in the compartment. (plus and minus poles to
respective mark)
3.Replace the coverof the battery compartment.
Precautions
Make sure that there is no
obstacle between theremote
controller and televisionset.
As strong light may interfere the
signals, change yourposition to
operate the remote controller if
the television cannot be turned
on or off as youexpect.
Keep the remote controller
away from heat source or
humid area toensure
effective performance of
the remote controller.
Make sure that two AA 1.5V alkaline
batteries are loaded. The batteries
must be of the same type. The batteries
must be located properly. The batteries
are not rechargeable.
Customer helpline:0845 604 0105

Connection Instructions
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connectingit to telephone wires, lightening rods, or gas pipes.
Grounding
External Equipment Connections
Antenna Connection
- Antenna or Cable Service with a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wallantenna socket)
wall antenna
socket
VHF antenna
UHF antenna
outdoor
antenna
Single-family Dwellings /Houses
(Connect to walljack for outdoor antenna)
Be careful notto bend the bronze
wire when connectingthe antenna.
To improve picture quality in a poor
signal area, purchase and install a
signal amplifier.
If the antenna needs to be split for two
TV s, install a 2-Way Signal Splitter
in the connections.
If the antenna is not installed properly,
contact your dealer for assistance.
NOTE: All cables shown are just for example.
RF coaxial wire(75 ohm)
ANT IN
ANT IN
Customer helpline:0845 604 0105

Connection Instructions
You can use your LCD-TV as a monitor for your personal computer using a VGA
cable (not supplied).
VGA Input
Connection and use steps:
1.Read the userguide supplied with
your computer and ensure that it has
a VGAconnector;
2.Make sure that the power of the LCD
-TV and thePC are off;
3.Connect a Dtype 15-pin VGAinterface
cable ( not supplied ) to the VGA video
interface connector on the PC. Then
connect the other end to the PC video
interface connector on the back of the
LCD-TV.Tighten the screwson the VGA
connectors once they are firmly
connected;
4.Turn on the power ofthe LCD-TV first ,
and then turn on the power of the PC;
5.Press the SOURCE button to set the video
input mode ofthe LCD-TV to PC-RGB;
6.Check the image on your TV. There may be noise associated with the resolution,
vertical pattern, contrast or brightness in PC mode. If noise is present, change
the PC mode to another resolution, change the refresh rate to another rate or
adjust the brightness and contrast on the menu until the picture is clear. If the
refresh rate of the PC graphic card cannot be changed,change the PC graphic
card or consult the manufacturer of the PC graphic card.
Frame frequency (Hz)Line frequency (Khz)
VGA
SVGA
XGA
640*480 31.5KHz 60Hz
800*600 37.9KHz 60Hz
1024*768 48.4KHz 60Hz
Resolution
Mode Resolution
Note: Allabove listed are subject to VESACriteria.
YPbPr Input
How to connect
Connect the DVD video outputs (Y, PB, PR)
to the COMPONENT(Y, Pb, Pr) IN socks on
the TV and connect theDVD audio outputs
to the AUDIO IN jacks on the TV, as shown
in the figure.
NOTE: If your DVD player does not have
component video output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the SOURCE button on theremote control toselect
VGA IN
Customer helpline:0845 604 0105

Connection Instructions
COMPONENT (If connected to S-VIDEO,select the S-VIDEO external
input source.)
3. Refer tothe DVD player's manual for operating instructions.
Component Input ports
To get better picture quality, connect a DVD player to the component
input ports as shown below.
S-VIDEO Input
Connection and use steps:
1.Read the user guide supplied with your AV devices and ensure that it has
S-Video connectors;
2.Make sure that the power of the LCD-TV and the AV device are switched off;
.Turn on the power of the LCD-TV first ;
and then turn on the power of the AV
device;
4.Press the SOURCE button to set the video
input mode of the LCD-TV to SVIDEO
mode .
Connection Option 1
Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.
Connection Option 2
1. Connect the audio and S-VIDEO cables
from the VCR's output jacks to the TV
input jacks, as shown in the figure.
2. Insert a video tape into the VCR and
press PLAY on the VCR. (Refer to the
VCR owner s manual.)
3
- To avoid picture noise (interference), leave an adequate distance between the
VCR and TV
.
VCR
1
2
Customer helpline:0845 604 0105

Connection Instructions
SCART Input
1.Connect the scartlead from the external device(DVD
players, settop boxesor game consoles, to the TV SCART
socket.
2.Press SOURCE to select SCART mode.
3. Press Play button on external equipment and it should
appear on the screen.
HDMI
HDMI
HDMI Input
HDMI Devices
Connect the cablefrom the HDMI devices
to the TV HDMI, as shown in thefigure.
How to use
1. Select theiHDMI source by using the SOURCE
button on theremote control.
2. Operate thecorresponding external equipment.
Refer to externalequipment operating guide.
SCART
External equipment
Note: The audio cableincluded with the TV should be used whenconnected with PC/
COMPONENT/S-VIDEO.
TV
HDMI Devices
Customer helpline:0845 604 0105

Basic Operating Instructions
Turn on the LCD-TV
When the POWER(STANDBY) button on the remote control
is pressed and the LCD-TV is turned on, the indicator light on
the front of the LCD-TV changes from red to green. When the
LCD-TV is turned off using the POWER(STANDBY) button,
the LCD-TVwill go into standby mode and the indicator light
turns red.
You can also turn on the TV from standby mode by pressing
the digits(1-9) orP+/- .
Audio Control
1.Press the V+ button to increase the volume.
2.Press the V- button to decrease the volume.
Mute
1.Press the MUTE button to mute the sound temporarily. A mute icon
appears on the screen.
2.Press the MUTE button again or V+ to restore the sound.
The mute icon disappears.
The display will appear on the screen when the TV is turned on the first time:
AUTO SEARCH
UNITED KINGDOM
NO
Press V+/- to adjust the region and P+/- to select the YES and MENU to confirm.
All channels willbe stored after the process.
YES
POWER OPEN/CLOSE
SCAN SWAP CALL MUTE
1234
5678
9900-/---/--
TV/AV
DTV/DVD
P+
P-
V- V+
MENU
ZOOM AUDIO
STOP SETUP PAUSE/STEP
REV FWD .PREV NEXT
D.MENU EXIT PROGRAM
PLAY/ENTER SUBTITLE
ANGLE TITLE/PBC SEARCH
SLOW D.CALL
10+
A-B
TUNE
NICAM
P.STD
EPG
OK
FAV i
REPEAT
SIZE TIME
REVEAL MODE
MIX TEXT
SUBCODE HOLD
Customer helpline:0845 604 0105

Basic Operating Instructions
Select the TV Channel You Want
You can use the number keys on the remote control to directly select TV
channels.
The LCD-TV can store up to 100 channels , and you can press the keys on the
remote control or on the panel to make a selection.
1. if you want to choose any channel from 0 to 9, please press the -/-- button
until -is indicated on the screen and then press the relevant key on the
remote control. for example: if you want to choose channel 8, just press the
Key number 8.
2.If you want to choose a channel bigger than 9, please press the -/-- button
until -- is indicated on the screen. Enter the two digits of the channel
number you want to watch.. for example: select channel 16
Note: if you want to choose one digit channel in this condition, you should press
0 first and then one digit number key.
Picture Mode
Press P.STD button on the remote control for menu display . For desired mode as
follows:
PERSONAL STANDARD MILD FRESH
Program Swap
1
2
3
Suppose the channel number you used channel now is 8 and the channel number you
are using is 18 (as shown in the figure).
If you want to return to the last watched program channel 8, you can simply press the
SWAP(Q.VIEW) button.
If you want to return to channel 18, press the button again. Through this function, you
can easily change between the channel you are using and the channel you used last time.
Customer helpline:0845 604 0105

Menu Operations
Picture Menu Options
1. Press MENU button to display the main menu, and V+/V-to select the
main menu .
2. Press P+/P- to scroll through the options
3. Press V+/V- buttons to make changes to the parameters
4. Press the EXIT button to exit the menu
Picture quality can be adjusted for any input separately .
The picture qualityon the screen can be adjustedas follows:
1. Press MENU button and V+/V- until the following menu appears
on the screen.
2. Press P+/P- button to enterthe picture menu and to go up and down to
select the desired option .
TV/S-VIDEO SCART MENU/DVD/
PC MENU
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
COLOUR TEMP.
30
30
30
2
COLD
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
H.POSITION
V.POSITION
COLOUR
30
30
30
2
30
HDMI/COMPONENT MENU
0
0
BRIGHTNESS
CONTRAST
SHARPNESS
NOISE REDUCE
HUE
COLOUR
PICTURE
50
50
2
50
OFF
Only available inNTSC system
50
Customer helpline:0845 604 0105

Menu Operations
3.Press V+/V- button to increaseand decrease the level to matchyour preference .
4. Repeat step 2 and step 3 until desired picture quality has been achieved .
Functions:
BRIGHTNESS :Adjust the brightness of the picture . By increasing the level, it
will add more light to dark parts of the picture and by decreasing the level ,it will
add more dark to light parts of the picture.
CONTRAST : The image becomes higher as the number increase.
SHARPNESS : By increasing the level, it will show cleaner and clearer images
and by decreasing the level, it will make picture smoother.
COLOUR : PressV+/V- to adjust the colour
NOISE REDUCE:Adjust the quality of the pictureby selecting OFF,LOW,MID,HIGH.
HUE :Adjust the tone of the picture. Appear and be adjustedonly under NTSC
mode
COLOUR TEMP. : Press to select the colour temperature from WARM/NORMAL/
COLD
H.POSITION : Picture horizontal adjust
V.POSITION : Picture verticalposition adjust .
.
Picture Menu Options continued
Audio Menu Options
Sound can beadjusted for as follows:
1. Press MENU and V+/V- button until the following menu appears on
the screen
VOLUME
BALANCE
BASS
TREBLE
AUDIO MODE
AVL
AUDIO
50
50
50
50
VOICE
OFF
Customer helpline:0845 604 0105

Menu Operations
Audio Menu Options continued
2. Press P+/P- button to enterthe audio menu and to go up and down to
select the desired option .
3.Press V+/V- button to increaseand decrease the level to matchyour preference .
4. Repeat step 2 and step 3 until desired sound quality has been achieved .
Functions :
VOLUME :Adjust the volume of your TV
BALANCE : Adjust the balance of the audio output from left to right . When
indication value of balance increases toward 100 , sound of the left speaker
becomes weaker .When indication value of balance decreasestoward 0 ,
sound of the right speaker become weaker .
BASS : Adjust the bass of the sound . Can only be adjust under PERSONAL mode .
TREBLE : Adjust the treble of the sound . Can only be adjust under PERSONAL
mode .
AUDIO MODE : Press V+/V- to select among PERSONAL, VOICE, MUSIC and
THEATRE .
AVL: Automatic Volume Limit Control reduces the effect of the large volume by
the same volume of all the channels .
Customer helpline:0845 604 0105

Menu Operations
Function Menu Options
Menu Language Selection:
The menus canbe shown on the screen inthe selected language. First select
your language.
1. Press MENU and V+/V- button until the following menu appears on the screen
2. Press P+/P- button to selectLANGUAGE.
3. Press V+/V- button to select your desired language.
From this point on, the on-screen menus will be shown in the language of your
choice.
1. Press MENU button and V+/V- until the following menu appears
on the screen.
2. Press P+/P- button to enterthe sound menu and to go up and down to
select the desired option .
3.Press V+/V- button to increaseand decrease the level to matchyour preference .
4. Repeat step 2 and step 3 until desired picture quality has been achieved .
Functions:
1. INPUT SOURCE : PC, COMPONENT , DVD ,HDMI , DTV, TV, SCART, S-VIDEO
2. TXT LANGUAGE: To switch the teletext languages.
3. TXT EAST/WEST:To select EASTor WEST ..
INPUT SOURCE TV
LANGUAGE ENGLISH
TXT LANGUAGE PAN EUROPEAN
TXT EAST/WEST EAST
BLUE SCREEN ON
DISPLAY MODE 4:3
RESET
CHILD LOCK
FUNCTION
INPUT SOURCE TV
LANGUAGE ENGLISH
TXT LANGUAGE PAN EUROPEAN
TXT EAST/WEST EAST
BLUE SCREEN ON
DISPLAY MODE 4:3
RESET
CHILD LOCK
FUNCTION
Customer helpline:0845 604 0105