Whip Mix Denar User manual

Denar® Universal Occlusal Stand
For mounting the working casts
at Bonwill’s Equilateral Triangle
on Denar, Hanau, and Whip Mix
articulators.
Includes two interchangeable tables:
Flat table for mounting; also accepts Kois Index
Tray from Panadent.
Curved table for mounting.
Both the at and curved table may sit at or at a 10 degree
angle. Only a small height adjustment is needed to set
either position at Bonwill’s Triangle.
The universal occlusal stand ts the Mark 300 magnetic
series articulators, the Denar and Hanau screw type
articulators, and the Whip Mix articulators with Quick
Mount magnetic system.
Product Includes:
•Occlusal Stand • 2 Taper Pins (for using on Mark 300 series)
•Denar / Hanau Thread Adapter •Two Tables: Flat and Curved
•Fence in Bag •Instructions •1⁄8” Hex Key
•5/64” Hex Straight Wrench
Denar®
Universal Occlusal Stand
Instruction Manual
Whip Mix Corporation
361 Farmington Avenue
Louisville, KY USA 40209
Toll-Free: 800-626-5651
Phone: [phone]
Fax: [phone]
www.whipmix.com
Whip Mix®, Denar® and logos are registered
trademarks of Whip Mix Corporation.
©2019 Whip Mix Corporation
FN 2 0 0117 19 - F A E R1119
Flat or Curved Table:
Using the top set screw and 1/8”
Hex Key, loosen the screw until
you are able to remove either
the at or curved table. Set in
the table you choose to use, and
tighten the top set screw.
Bonwill Settings:
Mounting without Kois
Index Tray
Using the front set screw on
the bottom cylinder and 5/64”
straight wrench, loosen the
screw until you are able to
move the middle cylinder up
and down.
Set the middle cylinder at its highest point and lock
into place.
Mounting with Kois
Index Tray
Use the at table with the
angle set to 0˚ (at).
Using the front set screw
on the bottom cylinder and
5/64” hex wrench, loosen
the screw until you are able
to move the middle cylinder
up and down. Set the middle
cylinder at its lowest point
and lock into place.
Adust the top cylinder to
the “0” setting for either the
Denar/Hanau or Whip Mix
articulator depending on
which you are using.
(See page 4.)
Attach Kois plate through holes in the mounting plate.
Table Angles
The table may be set at
either a at (0˚) angle or
10˚ angle. Using the Flat
Head screw on the side
underneath the table and
the 1/8” Hex Key, loosen
the screw until you are
able to freely move the
table to a at or angled
position. Set the table to
the desired position and
secure by tightening the
Flat Head screw.
Set
Screw
Set
Screw
Top Set
Screw
Flat Head
Screw
1 2 3

Key # Part # Description
1Base*
2 Base Post (Lower Cylinder)*
3 Extension (Middle Cylinder)*
42 0 011711 Thread Adapter
5R 20 0117 14 10-32 Flat Head Screw
62 0 011713 Flat Plate
72 0 0116 65 Taper Pin
820011717 Fence Assembly
9R3556 1/8” Hex Key
10 010727-000 5/64” Hex Key
11 34213 Curved Plate
*Requires Factory Repair
Articulator Mounting
Denar® Mark 300 series articulators
Be sure the two taper
pins are in place on the
bottom of the occlusal
stand. If not, snap into
place.
Leave the Denar /
Hanau thread adapter
in place for additional
magnetic strength.
After cleaning each
surface, place the
stand on the lower member of the articulator by lining
up the pins to the divots on the articulator.
Be sure the stand is fully seated on the articulator.
Denar / Hanau articulators*
Remove the two taper pins if
they are in place by using the
5/64” hex key to push through
the holes above the pins on
top of the stand base. Be sure
to save the taper pins in your
fence bag in case they are
needed in the future.
If needed, remove magnetic
converter plate from the lower member of your
articulator.
After cleaning each surface, attach the occlusal stand to
the lower member of the articulator by locating on the
dowel pins and tightening the mounting screw.
* Plate does not sit at Bonwill on Hanau-Mate™ or Ulti-Mate™ articula-
tors.
Whip Mix articulators with Quick Mount magnetic
system
Remove the two taper pins if they are in place by using
the 5/64” straight wrench to push through the holes
above the pins on top of the stand base. Be sure to save
the taper pins in your fence bag in case they are needed
in the future.
Articulator Setting
Using the side set screw on the middle cylinder and the
5/64” straight wrench, loosen the screw until you are able to
raise and lower the top cylinder.
You will notice four markings on the cylinder:
WM
–0
D/H
–0
WM
–10
D/H
–10
If you are using a Whip Mix
articulator with the table at 0˚
move the cylinder so that the
WM –0 line is positioned at the
top of the middle cylinder. The WM –0 lettering should be
visible if aligned correctly. Tighten the set screw to secure
the cylinder position.
If you are using a Denar or Hanau articulator with the table at
0˚, use the D/H – 0 position.
If you are using a Whip Mix articulator with the table at 10˚,
use the WM – 10 position.
If you are using a Denar or Hanau articulator with the table at
10˚, use the D/H – 10 position.
When using the at table at a
0° angle (at), the fence may be
used to line up the incisal edge
of the casts. Be sure the text
Flat on the fence is next to the
casts.
When using the at table at
a 10° angle, the fence may be
used to line up the incisal edge
of the casts. Be sure the text
10 Degree on the fence is next
to the casts.
Using a at screwdriver or coin, loosen the Denar / Hanau
thread adapter and remove. Be sure to save the thread
adapter in your fence bag in case needed in the future.
After cleaning each surface, snap the occlusal stand on
to the quick mount system on the lower member of the
articulator.
For Whip Mix screw type articulators, please contact
customer service for information on converting to a
magnetic system.
1
47 7
2
10
9
3
5
6
8
511
Set
Screw
Settings
Taper Pins
Thread
Adapter
4 5 6