Whirlpool EV250NXTQ00 User manual

UPRIGHTFREEZER
For questions about features, operation/perlormance,
parts or service, call: 1-800-25a-1301.
In Canada, call for assistance 1-800-807-6777,
or visit our website at...
www.whirlpool.com or www.whirlpool.com/canada
CONGELATEUR
VERTICAL
Au Canada, pour assistance, composez le 1-800-807-6777.
ou visitez notre site web www.whirlpool.com/eanada
Table of Contents/Table des matieres .................. 2
W10326799A

TABLEOFCONTENTS
FREEZER SAFETY ....................................................................................... 3
Proper Disposal of Your Old Freezer or Refrigerator ............................... 3
INSTALLATION INSTRUCTIONS ............................................................... 4
Unpacking ................................................................................................. 4
Location Requirements ............................................................................. 4
Electrical Requirements ............................................................................ 5
Water Supply Requirements ..................................................................... 5
Connect the Water Supply ....................................................................... 6
Freezer Door ............................................................................................. 6
Adjust the Door ......................................................................................... 9
FREEZER USE ............................................................................................. 9
Ensuring Proper Air Circulation ................................................................ 9
Using the Control ...................................................................................... 9
Indicator Light ......................................................................................... 10
Key Eject Lock ........................................................................................ 10
Ice Maker ................................................................................................ 10
FREEZER FEATURES ............................................................................... 10
Refrigerated Shelves .............................................................................. 10
Door Bin .................................................................................................. 11
Storage Basket ....................................................................................... 11
Storage Gate ........................................................................................... 11
FREEZER CARE ........................................................................................ 11
Cleaning Your Frost-Free Freezer .......................................................... 11
Base Grille ............................................................................................... 12
Defrosting and Cleaning Your Manual Defrost Freezer ......................... 12
Changing the Light Bulb ......................................................................... 13
Power Interruptions ................................................................................ 13
Moving Care ........................................................................................... 13
TROUBLESHOOTING ............................................................................... 13
ASSISTANCE OR SERVICE ...................................................................... 15
In the U.S.A ............................................................................................. 15
In Canada ................................................................................................ 15
Accessories ............................................................................................. 15
WARRANTY ............................................................................................... 16
TABLEDESMATIERES
SECURITE DU CONGELATEUR ............................................................... 17
Mise au rebut appropriee de votre
vieux cong61ateur ou refrigerateur .......................................................... 17
INSTRUCTIONS D'INSTALLATION ......................................................... 18
Deballage ................................................................................................ 18
Emplacement d'installation .................................................................... 18
Specifications electriques ....................................................................... 19
Specifications de I'alimentation en eau .................................................. 19
Raccordement de la canalisation d'alimentation en eau ....................... 19
Porte du cong61ateur .............................................................................. 20
Ajustement de porte ............................................................................... 23
UTILISATION DU CONGleLATEUR .......................................................... 23
Pour s'assurer d'une circulation d'air appropriee .................................. 23
Utilisation de la commande .................................................................... 23
Temoin indicateur ................................................................................... 24
Serrure & ejection de cle ......................................................................... 24
Machine & gla£;ons .................................................................................. 24
CARACTI_RISTIQUES DU CONGI_LATEUR ........................................... 25
Clayettes de refrigeration ....................................................................... 25
Balconnet de porte ................................................................................. 25
Panier d'entreposage ............................................................................. 25
Barriere d'entreposage ........................................................................... 25
ENTRETIEN DU CONGleLATEUR ............................................................ 25
Nettoyage du cong61ateur sans givre .................................................... 25
Grille de la base ...................................................................................... 26
Degivrage et nettoyage du cong61ateur & degivrage manuel ................ 26
Remplacement de I'ampoule d'eclairage ............................................... 27
Pannes de courant electrique ................................................................. 27
Demenagement ...................................................................................... 27
DlePANINAGE ............................................................................................. 28
ASSISTANCE OU SERVICE ...................................................................... 30
Accessoires ............................................................................................. 30
GARANTIE .................................................................................................. 31
2

FREEZERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:To reduce the risk of fire, electric shock, or injury when using your freezer, follow these basic precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before servicing.
• Replace all parts and panels before operating.
• Use nonflammable cleaner.
[] Keep flammable materials and vapors, such as gasoline,
away from freezer.
[] Use two or more people to move and install freezer.
[] Keep key away from children.
• Remove doors or lid from your old freezer or refrigerator.
[] Disconnect power before installing ice maker (on ice maker
kit ready models only).
SAVE THESE INSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains a chemical known to the State of California to cause cancer.
WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.
Proper Disposal of
Your Old Freezer or Refrigerator
Suffocation Hazard
Remove doors or lid from your old freezer or
refrigerator.
Failure to do so can result in death or brain damage.
Before You Throw Away Your Old Freezer or Refrigerator:
• Takeoff the doors or lid.
• Leave the shelves in place so that children may not easily
climb inside.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned freezers or refrigerators are still
dangerous.., even if they will sit for "just a few days." If you are
getting rid of your old refrigerator or freezer, please follow these
instructions to help prevent accidents.

INSTALLATIONINSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install freezer.
Failure to do so can result in back or other injury.
Remove Packaging Materials
• Remove tape and glue residue from surfaces before turning
on the freezer. Rub a small amount of liquid dish soap over the
adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your freezer. For more
information, see "Freezer Safety."
When Moving Your Freezer:
Your freezer is heavy. When moving the freezer for
cleaning or service, be sure to cover the floor with cardboard
or hardboard to avoid floor damage. Always pull the freezer
straight out when moving it. Do not wiggle or "walk" the
freezer when trying to move it, as floor damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside of
your freezer before using it. See the cleaning instructions in
"Freezer Care."
important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from freezer.
Failure to do so can result in death, explosion, or fire.
IMPORTANT: Do not install the freezer near an oven, radiator, or
other heat source, nor in a location where the temperature will fall
below 40°F (5°C).
Check the strength of the floor before installing your freezer. It
should hold the weight of a freezer fully loaded with food.
Allow at least 3" (7.5 cm) of air space at the top and on both sides
of the freezer and 1" (2.5 cm) between the back of the freezer and
the wall. If the freezer is to be against a wall, leave extra space on
the hinge side so the door can open wider.
NOTE: This freezer may be installed side by side with another
refrigerator or freezer. Allow for a 3" (7.5 cm) clearance at the top
and sides and a 1/4"(0.64 cm) clearance between the appliances.
3" (7.5 cm)

Electrical Shock Hazard
Plug into agrounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your freezer into its final location, it is important
to make sure you have the proper electrical connection.
Recommended grounding method
A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your freezer be provided. Use an outlet that
cannot be turned off by aswitch. Do not use an extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the Temperature Control to the OFF
position as shown and then disconnect the freezer from the
electrical source.
<1
Read all directions before you begin.
IMPORTANT:
• If you turn the freezer on before the water line is connected,
turn the ice maker OFE
• All installations must meet local plumbing code requirements.
• Use plastic tubing and check for leaks. Install plastic tubing
only in areas where temperatures will remain above freezing.
TOOLS NEEDED: Flat-blade screwdriver, 7/le"and V2"open-end
wrenches or two adjustable wrenches, V4"nut driver, drill bit and a
cordless drill.
NOTE: Your freezer dealer has a kit available with a V4"(6.35 mm)
saddle-type shutoff valve, a union, and plastic tubing. Before
purchasing, make sure a saddle-type valve complies with your
local plumbing codes. Do not use a piercing-type or ¾e"
(4.76 mm) saddle valve which reduces water flow and clogs more
easily.
Water Pressure
A cold water supply with water pressure of between 30 and
120 psi (207 to 827 kPa) is required to operate the water
dispenser and ice maker. Ifyou have questions about your water
pressure, see "Troubleshooting" or call a licensed, qualified
plumber.
Reverse Osmosis Water Supply
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the system needs to be a
minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than 40
to 60 psi (276 to 414 kPa), a booster pump can be inserted into
the small tubing that goes from the cold water line to the reverse
osmosis system.
If the water dispenser is still not dispensing water properly:
• Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
• Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
• If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter.
If you have questions about your water pressure, refer to
"Troubleshooting" or call a licensed, qualified plumber.

Connect to Water Line
1. Unplug freezer or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a 1/2"to 11/4"(12.7 mm to 3.18 cm) vertical cold water
pipe near the freezer.
IMPORTANT:
• Make sure it is a cold water pipe.
• Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
4. Determine the length of plastic tubing you need. Measure from
the connection on the lower left rear of freezer to the water
pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"(6.35 mm)
O.D. (outside diameter) plastic tubing. Be sure both ends of
plastic tubing are cut square.
5. Using a cordless drill, drill a 1/4"(6.35 mm) hole in the cold
water pipe you have selected.
A. CoM wa_rp_e
B.Pipe c_mp
C. Copper _b_g
D. Compression nut
E. Compression sleeve
KShutoff valve
G. Packing nut
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
Do not overtighten or you may crush the plastic tubing.
7. Slip the compression sleeve and compression nut on the
plastic tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and turn
ON the main water supply. Flush the tubing until water is clear.
Turn OFF the shutoff valve on the water pipe. Coil the plastic
tubing.
Connect to Freezer
1. Attach the plastic tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do not
overtighten.
2. Use the tube clamp on the back of the freezer to fasten the
tubing to the freezer as shown. This will help avoid damage to
the tubing when the freezer is pushed back against the wall.
3. Turn shutoff valve ON.
4, Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
5=
A. Tube clamp
B. Tube clamp screw
C. Plastic tubing
D. Compression nut
E. Valve inlet
The ice maker is equipped with a built-in water strainer. If your
water conditions require a second water strainer, install it in
the 1/4"(6.35 mm) water line at either tube connection. Obtain
a water strainer from your nearest appliance dealer.
Electrical Shock Hazard
Plug into agrounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
6. Plug into a grounded 3 prong outlet.
TOOLS NEEDED: 8/le"hex head socket wrench, 5/8"hex head
socket wrench, 1/4"hex head socket wrench, 1/2"hex head socket
wrench, 3/8"hex head socket wrench, #2 Phillips screwdriver, flat-
blade screwdriver, 8/F open-end wrench, flat 2" putty knife.
IMPORTANT:
All graphics referenced in the following instructions are
included later in this section after "Final Steps." The graphics
shown are for a right-hand swing door (hinges factory installed
on the right).
• If you only want to remove and replace the door, see the
"Remove Door and Hinges" and "Replace Door and Hinges."
• Before you begin, turn the control OFF, and remove food and
adjustable door or utility bins from door.
6

Remove Door and Hinges
5_6" Hex Head Hinge Screw
1. Unplug freezer or disconnect power.
2. Open freezer door and remove base grille from the bottom
front of the freezer. See Base Grille Graphic 1A.
3. Close the freezer door and keep it closed until you are ready
to lift it free from the cabinet.
NOTE: Provide additional support for the door while the
hinges are being moved. Do not depend on the door magnets
to hold the door in place while you are working.
4. Remove the parts for the top hinge as shown in Top Hinge
Graphic 1B.
5. Lift the freezer door free from the lower hinge and cabinet and
set aside.
6. Remove three hex head hinge screws and bottom hinge
assembly. See Bottom Hinge Graphic 1C.
Reverse Door (optional on some models)
2.
3.
4.
5.
IMPORTANT: If you want to reverse your door so that it opens in
the opposite direction, continue with "Reverse Door (optional on
some models)" instructions. If you are not reversing the door, see
"Replace Door and Hinges."
Cabinet
1. Remove the cabinet hinge hole plugs from the cabinet top and
move them to the opposite side hinge holes as shown in
Graphic 2.
Remove the door stop screws from the Bottom Hinge bracket.
See Bottom Hinge Graphic 1C.
Remove the Hinge Pin Nut and Hinge Pin from the hinge
bracket.
Rotate the hinge bracket for installation on the opposite side
of the cabinet. See Graphic 3.
Reinstall the Hinge Pin Nut and Hinge Pin to the hinge
bracket. Hinge Pin must point "up" when hinge bracket is
installed to the cabinet.
6. Invert the door stop so that the countersunk holes line up with
the screw holes in the hinge assembly. See Graphic 4.
7. Reinstall the door stop screws. See Graphic 3.
8. Reinstall the hinge bracket to the cabinet with the 3 hex head
hinge screws.
Handle
Move the door handle from one side of the door to the other.
Style 1
1. Grasping the lower part of the handle firmly, slide it up and pull
the handle straight out from the door. See Graphic 1-1.
2. Using a %" hex head socket wrench, remove the grommets
from the door.
3. Reinstall the grommets on the opposite side of the door.
4. Position the handle so that the large holes in the mounting
clips are down and align the holes with the grommets.
5. Rotate the handle so that the mounting clips are flat against
the door and slide the handle down to engage.
Style 2
1. Loosen setscrews located on side of handle at each end. See
Graphic 1-2.
2. Remove handle from grommets.
3. Using a 1/4"hex head socket wrench, remove the grommets
from the door.
4. Position the grommets on the opposite side of the door and
reinstall.
5. Position the handle over grommets on the opposite side of the
freezer door.
6. Ensure grommets are fitted into handle holes.
7. Tighten the upper and lower setscrews with hex key provided.
Do not overtighten setscrews.
Style 3
1. Slide the handle up and off the clips. See Graphic 1-3.
2. Using a flat-blade screwdriver, remove the screws from the
clips and remove the clips from the door.
3. Position the clips on the opposite side of the freezer door and
reinstall the screws.
4. Position handle over the clips.
5. Apply even pressure and push down to lock in place.
Replace Door and Hinges
NOTE: Graphic may be reversed if door swing is reversed.
1. Replace the parts for the bottom hinge as shown and tighten
screws. See Bottom Hinge Graphic 1C. Replace the freezer
door.
NOTE: Provide additional support for the door while the
hinges are being moved. Do not depend on the door magnets
to hold the door in place while you are working.
2. Assemble the parts of the top hinge as shown in the Top
Hinge Graphic 1B. Do not tighten the screws completely.
3. Line up the door so that the bottom aligns evenly with the
cabinet. Tighten all screws.
Final Steps
1. Check all holes to make sure that hole plugs and screws are in
place. Reinstall top hinge cover. See Top Hinge Graphic 1B.
2. Replace the base grille. See Base Grille Graphic 1A.
Electrical Shock Hazard
Plug into agrounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
3. Plug into a grounded 3 prong outlet.
4. Reset the control. See "Using the Control."
5. Return all removable door parts to door and food to freezer.

A. Door Stop Screws
B. Door Stop
C. Hinge Pin
D. Hinge Pin Nut
A................................_
A. Cabinet Hinge Hole Plugs
n
Left Hand Hinge Right Hand Hinge
Door Stop Door Stop |
•..... :':'.. :,:. Oo.. o
[
;:::-,.............._,:................
D.................................'_
A. Door Stop Screws
B. Door Stop
C. Hinge Pin
D. Hinge Pin Nut
E. %" Hex-Head Hinge
Screws
/
I
/
Style 1
A. Grommet
B. Clip
C. Handle
A
Style 2
A. Grommet
B. Handle
C. Setscrews
o
Door Handle
Seal Screw
Style 3
A. Clips
B. Handle Screws
C. Handle
8

Locate the two front leveling legs taped among the packing
materials.
1=
2. Screw these legs into the front holes on the bottom of the
freezer. The back of the freezer rests on two fixed supports.
3. Adjust the front legs enough to lift the cabinet up off of the
floor.
4=
NOTE: If your model is equipped with rollers, the front legs
should be lowered enough to lift the rollers off of the floor to
ensure the freezer does not roll forward when the door is
opened.
Place a leveling tool on top of the freezer first side to side,
then front to back. Turn leg counterclockwise to raise a corner.
Turn leg clockwise to lower a corner.
5. Repeat Step 4 until freezer is level.
6. After freezer is fully loaded with food, recheck with level as in
Step 4.
FREEZERUSE
In order to ensure proper temperature, you need to permit proper
airflow in the freezer. As shown in the illustration, cool air enters
through the freezer wall and moves down. The air then
recirculates through the vent near the bottom.
Do not block any of these vents with food packages. If the vents
are blocked, airflow will be restricted, and temperature and
moisture problems may occur.
IMPORTANT: To avoid odor transfer and drying out of food, wrap
or cover foods tightly.
Turn the freezer temperature control to 4. This setting is designed
to maintain the temperature at or near 0°F (-17.8°C) under normal
operating conditions.
Allow the freezer to cool 6 to 8 hours before filling with frozen
food. Let the freezer cool overnight before adding large amounts
of unfrozen food. Do not add more than 2 to 3 Ibs (907 to 1,350 g)
of unfrozen food per cubic foot (28.32 L) of freezer space.
NOTE: When the freezer is first started, the compressor will run
constantly until the freezer is cooled. It may take up to 6 or
8 hours (or longer), depending on room temperature and the
number of times the freezer door is opened. After the freezer is
cooled, the compressor will turn on and off as needed to keep the
freezer at the proper temperature.
The outside of your freezer may feel warm. This is normal. The
freezer's design and main function is to remove heat from
packages and air space inside the freezer. The heat is transferred
to the room air, making the outside of the freezer feel warm.
Adjusting Control
Turn control to a higher number for colder temperatures.
Turn control to a lower number for less cold temperatures.
NOTE: The small snowflake icon represents the number 1 or
the least cold setting. The large snowflake icon represents 6 or
the coldest setting.
Fast Freeze (on some models) _
This setting causes the freezer to run continuously, driving the
freezer temperature to the coldest possible temperature. To
activate, adjust the control knob to the igloo icon, which
represents the fast freeze setting. Use this feature just before
adding large amounts of unfrozen foods. For best food quality, do
not exceed 3 Ibs (1,350 g) per cubic foot (28.32 L). Return to your
normal setting after 24 to 48 hours.

Temperature Alarm (on some models)
The temperature monitor alarm is located to the left of the
temperature control and sounds an audible alarm if the
temperature reaches 10°F (-12°C) or more above normal for the
selected setting.
The alarm is controlled by a three-position switch.
I
0
The proper setting for normal freezer use. The alarm
is on, and the amber light will be illuminated.
Keeps the alarm from sounding when the freezer is
warm, such as during start-up or defrosting.
Tests the alarm regardless of temperature.
The indicator light assures you that your freezer is running. If the
indicator light is not glowing, immediately check for:
• Power interruption.
• An unplugged power cord.
• An open circuit breaker or blown fuse.
• A burned out indicator light.
To lock or unlock the freezer, you must hold the key in the lock
while turning. The lock is spring loaded, so the key cannot be left
in the lock.
If the key is lost, contact your dealer for a replacement. Always
give the model and serial number of your freezer when requesting
a replacement key.
ToTurn the Ice Maker On/Off
NOTE: Do not force the wire shutoff arm up or down.
• To turn the ice maker on, simply lower the wire shutoff arm.
NOTE: Your ice maker has an automatic shutoff. As ice is
made, the ice cubes fill the ice storage bin and the ice cubes
will raise the wire shutoff arm to the OFF (arm up) position.
• To manually turn the ice maker off, lift the wire shutoff arm to
the OFF (arm up) position and listen for the click to make sure
the ice maker will not continue to operate.
Ice Production Rate
The ice maker should produce approximately 7 to 9 batches of ice
in a 24-hour period. If ice is not being made fast enough, turn the
Temperature Control toward a higher (colder) number in half
number steps. (For example, if the control is at 3, move it to
between 3 and 4.) Wait 24 hours and, if necessary, gradually turn
the Temperature Control to the highest setting, waiting 24 hours
between each increase.
Remember
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
The quality of your ice will be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If asoftened water supply cannot be avoided,
make sure the water softener is operating properly and is well
maintained.
Do not store anything on top of the ice maker or in the ice
storage bin.
FREEZERFEATURES
This manual covers several different models. The freezer you have
purchased may have some or all of the items listed. The locations
of the features may not match those of your model.
Your freezer is equipped with refrigerated interior shelves.
Packages in direct contact with the shelves will have the best
refrigeration. Fresh, unfrozen food packages should be stored
directly on the shelves and not on top of already frozen food
packages.
10