Refrigerator
®
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 2314472
02-22-07
1
/
2" (1.25 cm)
2" (5.08 cm)
" (7.5 cm)
3
To ensure proper ventilation for your refrigerator, allow for 1⁄2 in. (1.25 cm) space
on each side and at the top. (At the top, when using half depth cabinet, use top
of cabinet height “D” dimension. When using full depth cabinet, use overall “E”
dimension.) When installing your refrigerator next to a fixed wall, leave 2 in. (5.08
cm) minimum on each side (depending on your model) to allow for the door to
swing open. If your refrigerator has an ice maker, allow extra space at the back for
the water line connections.
NOTE: Do not install the refrigerator near an oven, radiator, or other heat source,
nor in a location where the temperature will fall below 55°F (13°C).
4
1
E
overall
D
top of
cabinet
CC
D
top of
cabinet
B
B
not incl.
handle
A
Integrated
Model
Standard
Model
E
overall
A
Depth Cab. Width Door Width Cab. Height Overall Height
Model size “A” “B” “C” “D” “E”
STANDARD MODELS
18 cu.ft. 29 3/8” 29 1/2” 29 3/4” 65 1/2” 66 1/4”
19 cu.ft. 30 3/4” 29 1/2” 29 3/4” 65 1/2” 66 1/4”
21 cu.ft. 29 3/8” 32 1/2” 32 3/4” 65 1/2” 66 1/4”
22 cu.ft. 30 3/4” 32 1/2” 32 3/4” 65 1/2” 66 1/4”
INTEGRATED MODELS
19 cu.ft. 31 1/2” 29 1/2” 30 1/8” 65 1/2” 66 1/2”
22 cu.ft. 31 1/2” 32 1/2” 33 1/8” 65 1/2” 66 1/2”
LOCATION REQUIREMENTS
ER2CHMXP
ER2MHKXP
ET1CHEXS
ET1CHMXK
ET1FTEXS
ET1FTKXK
ET1LFKXK
ET1MHEXR
ET1MHKXM
ET1MHMXR
ET1PHKXP
ET8CHEXS
ET8CHKXK
ET8CHMXK
ET8FTEXR
ET8FTEXS
ET8LFKXK
ET8MHEXR
ET8MHKXM
ET8MHMXR
ET8WTEXM
ET8WTKXK
ET8WTMXK
GR2FHMXP
GR9FHKXP
GR9FHMXP
GT2SHKXM
GT2SHMXM
Electrical: A 115 Volt, 60 Hz., AC only 15 or
20 amp fused, grounded electrical supply is
required. It is recommended that a separate
circuit serving only your refrigerator be pro-
vided. Use an outlet that cannot be turned
off by a switch. Do not use an extension
cord.
Water: Connect the ice maker to a cold
water line with water pressure between 30
and 120 psi.
If a reverse osmosis water filtration system
is connected to your cold water supply, the
water pressure to the system needs to be a
minimum of 40 to 60 psi (276 - 414 kPa).
IMPORTANT: The pressure of the water
coming out of a reverse osmosis system go-
ing to the water inlet valve of the refrigerator
needs to be between 30 and 120 psi
(207 - 827 kPa).
