Whirlpool WFC 3C26 User manual

FEATURE DEFENITION
60 cm. Dishwasher
Single Rack Washing Option
Upper Rack Removability
14-Place Settings
Flexible Washing Option
Energy Efficient
SRP: 32,998php
8 Programs
9-liter Water Consumption
Start-delay Function

MAIN FEATURE

MAIN FEATURE

ACCESSORIES
Lower Basket
Upper Basket

TECHNICAL SPECIFICATIONS
SPECIFICATIONS WFC 3C26
EN Code 8003437205453
Contruction Type Free Standing
Type of Control Electronics
Wattage (W) 1750
Current (A) 13
Voltage (V) 220
Frequency (Hz) 60
Electrical Supply Cord (cm) 130
Plug Type Uk
Inlet hose length (cm) 155
Outlet hose length (cm) 150
Product Height 850
Width of the product 600
Depth of the product 590
Net Weight (kg) 47
Gross Weight(kg) 49

TECHNICAL SPECIFICATIONS
SPECIFICATIONS
WFC 3C26
Automatic Programs Yes
Max Temp water inlet (Celsius) 60
Start delay option Cont.
Start delay time max (hours) 24
Digital Countdown Indicator Yes
Salt light indicator Yes
Rinse aid light indicator Yes

MODEL AND SERIAL NUMBER LOCATION
Serial number and model can be found
on the right side of the door

PRE-INSTALLATION REQUIREMENTS
Required Power Outlet:
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and
the retaining elastic elements from the upper rack.

COMPONENT ACCESS
1. Upper Rack
2. Cutlery Rack
3. Foldable Flaps
4. Upper Rack Height
Adjuster
5. Upper Spray Arm
6. Lower Rack
7. Lower Spray Arm
8. Filter Assembly
9. Salt Reservoir
10.Detergent and Rinse
Aid Dispenser
11.Model and Serial
12.Control Panel

COMPONENT ACCESS
1. On-Off/Reset Button
2. Program Selection Button
3. Multizone Button / Key Lock Indicator
4. Eco Program Indicator
5. Key Lock Indicator
6. Display
7. Program number
8. Tablet tab Indicator
9. Closed water tap Indicator
10.Rinse Aid refill Indicator Light
11.Salt Refill Indicator
12.Sani Rinse Button Indicator
13.Delay Button
14.Start/Pause with Indicator/ Drain out

OPERATIONAL REQUIREMENTS
FIRST TIME USE
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
• It is important that the salt reservoir be never empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher (see
PROGRAMS DESCRIPTION) and should be filled when the SALT REFILL
indicator light in the control panel is lit.
1.Remove the lower rack and unscrew the reservoir cap (anticlockwise).
2.Position the funnel and fill the salt reservoir right up to its edge
(approximately 1 kg); it is not unusual for a little water to leak out.
3.Remove the funnel and wipe any salt residue away from the opening

OPERATIONAL REQUIREMENTS
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that the water hardness
setting is based on the actual water hardness in your house.
The factory setting is for average (3) water hardness.
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button START/PAUSE for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
• The current selection level number and the salt indicator light both flash.
• Press button P to select the desired hardness level.

OPERATIONAL REQUIREMENTS
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be filled when the
RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Carefully introduce the rinse aid as far as the maximum (110 ml) reference notch of the
filling space - avoid spilling it. If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.

OPERATIONAL REQUIREMENTS
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust the quantity of
rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
• Press button START/PAUSE three times - a beep will be heard.
• Switch it on using the ON/OFF button.
• The current selection level number and rinse aid indicator light flash.
• Press button P to select the level of rinse aid quantity to be supplied.
• Switch it off using the ON/OFF button

OPERATIONAL REQUIREMENTS
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device A. Introduce the detergent into
the dry dispenser B only. Place the amount of detergent for pre-washing directly inside
the tub.
1.When measuring out the detergent Compartment B comprises a level showing the maximum
quantity of liquid or powder detergent that can be added to each cycle.
2. Remove detergent residues from the edges of the dispenser and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until the closing device is secured in
place.

PROGRAMS TABLE

OPERATIONAL DESCRIPTION

LOADING THE RACKS

LOADING THE RACKS