Whitmor 6905-12310-5-SIOC User manual

6905-12310-5-SIOC Leaning Shoe Rack
Tools Needed:
Phillips Screwdriver
Hammer
A1 ea
Left Top
C3 ea
Left Middle
I2 ea
Sticky Hooks
G15 ea
Horizontal Tubes
E1 ea
Right Foot
B1 ea
Left Foot
Part Reference
F11440
F11441
F11442
F11443
F11444
F11445
F11446
F11447
F11448
F11449
F11450
A
B
C
D
E
F
G
H
I
J
K
F3 ea
Right Middle
©2021 Whitmor, Inc.
H2 ea
Buckles
STEP 1: Assemble Left and Right Side Frames.
Start by assembling the left side frame.
Attach top left piece (A) to top left middle piece (C).
Attach top left middle piece (C) to left middle piece (C).
Attach left middle piece (C) to bottom left middle piece (C).
Attach left foot piece (B) to bottom left middle piece (C).
Repeat to assemble the right side frame.
L
L
L
L
R
D1 ea
Right Top
R
R
R
J2 ea
Tapping Screws
K2 ea
Dry Wall Anchor
R
R
R
R
R
R
R
R
R
NOTE: Make sure to attach
right pieces to right side frame
and left pieces to left side
frame. Displayed on each
piece is a “L” signifying left side
or “R” signifying right side.
A
D
C
C
C
B
F
F
F
E
.
NOTE: Fasten side frame
pieces using slide and
lock mechanism located
onto the bottom of each piece.
L
L R
R
R
L

STEP 2: Connect frames by attaching horizontal tubes.
Insert 15 horizontal tubes (G) into the holes located on left
side frame.
Align tubes with right frame starting from the holes on the bottom.
Gently push the right frame onto the tubes.
Flip unit on the opposite side and push the tubes in all the way.
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
R
R
R
R
R
R
R
R
NOTE: Pull out four
accessory hooks for
additional storage
located on the outer
sides of the left and
right top pieces.
R
R
R
R
R
R
R
R

Wall
STEP 1: Create pencil marks to show guides
for dry wall anchors.
Slide two buckles (H) onto top back of
both frames.
R
R
R
R
R
R
R
R
R
STEP 2: Drywall installation.
Use the pencil marks as a guide to place dry wall
anchors (K) into the wall.
Take a nail-set, awl, or nail and tap approximately
3/16 in (5mm) “pilot holes” into the pencils marks
located on the wall. DO NOT make the holes wider
than the anchors.
Place the dry wall anchors (K) over the hole and
firmly tap them in until they are flush with the wall.
Wall
HH
H
K
H
H
J
J
K
K
STEP 3: Attach unit to wall using taping screws.
Remove both buckles (H) from unit.
Attach both buckles (H) onto the wall anchors using
two tapping screws (J) and a Phillips screwdriver
(not included).
Slide the top of the unit onto the buckles (H)
Use pencil to mark on the wall where the screws
holes are located.
Wall
OPTION 1: Attach unit to wall using tapping
screws (J) , dry wall anchors (K), and
buckles (H) .

I
STEP 1: Attach sticky hooks to the wall.
Place two sticky hooks (I) and stick onto the wall.
OPTION 2: Attach unit to wall using sticky hooks (I).
Rev#0 | 04.22.21 Printed in China
8680 Swinnea Road • Suite 103 • Southaven, MS • 38671
NEED HELP? For help with assembly, or if you are missing a part, please call Whitmor’s Consumer Care Team, 1-888-944-8667 between 8 a.m. and 4:30 p.m.
(Central Standard Time) Monday through Friday, or email: [e-mail]. Visit us online at www.whitmor.com
STEP 2: Attach unit to sticky hooks on the wall.
Once sticky hooks (I) are attached onto the wall, slide the top of the unit onto the sticky hooks (I).
R
R
R
R
R
R
R
R
R
Wall
I
II