Wickes MONO SINK MIXER User manual

Please note: Tap heads shown are for illustration purposes only.
MONO SINK MIXER
INSTRUCTION MANUAL

CONTENTS
GUARANTEE
GENERAL SAFETY INSTRUCTIONS
PARTS SUPPLIED
HOW TO INSTALL
AFTER CARE
GUARANTEE
All products parts are manufactured to the highest standard and are covered by a 10 year
manufacturing guarantee.
GENERAL SAFETY INSTRUCTIONS
Prior to drilling into walls, check there are no hidden electrical wires, cables or water supply pipes
with the aid of an electronic detector.
Always wear protective equipment such as safety glasses and hearing protection whilst using power
tools.

HOW TO INSTALL
BEFORE YOU START
If the tap is installed into a low pressure (tank fed) system, the minimum height from the outlet
of the nozzle to the underside of the water tank, should be at least 2 metres to ensure adequate
performance.
This product must be connected to the water supply in accordance with the Water Supply (Water
Fittings) Regulations 1999, and also to comply with UK Building Regulations. If you are in any doubt
about these requirements, contact a qualified plumber, your local Water Company or the Water
Regulations Advisory Service (WRAS).
a. Identify all components and check pack contents.
b. TURN OFF WATER MAINS SUPPLY. The mains stopcock is usually situated where the supply enters
the building.
c. It is also recommended that the water heating arrangements are turned off.
d. Isolate the hot and cold supply pipes and drain both water systems. It is recommended to ensure
complete drainage, that all taps are open. There is no need to drain the heating system.
PARTS SUPPLIED
LIST
Tap Body & Valve
Body Seating
Flange
Washer(Anti-Rotational)
Rubber Horseshoe Washer
Metal Horseshoe Washer
Fixing Nut
Threaded Studs
Braided Connector
1 SETS
1 PCS
1 PCS
1 PCS
1 PCS
1 PCS
1 PCS
1 PCS
2 PCS

AFTER CARE
Your fitting has a high quality finish and should be treated with care to preserve the visible surfaces.
All surfaces will wear if not cleaned correctly. The only safe way to clean your fitting is to wipe with
a soft damp cloth using clean soapy water. Stains can be removed using a little washing up liquid. Do
FITTING INSTRUCTIONS
1. Screw Threaded Stud(8) into Tap Body(1).
2. Fit Body Seating(2) to the Tap Body(1), make sure the
convexity of Body Seating(2) will keep upturned, and then put
diagonal of the Grub Screw into diagonal the hole at the bottom
of Tap Body(1).
3. Check that Anti-Rotational Washer(4) is fitted to Flange(3).
Assemble Flange(3) to Tap Body(1), Screw the Braided
Connector(9) to the Tap Body(1), and then locate the tap
assembly down though hole in the sink.
4. Fit Rubber Horseshoe Washer(5) and Metal Horseshoe
Washer(6) onto Threaded Stud(8). Now fit Fixing Nut(7) onto
Threaded Stud(8). DO NOT OVERTIGHTEN.
5. Bend the Braided Connector(9) to the water supply using
suitable plumbing joints.
6. Turn on the water supply and re-fill the system. Check
immediately for leaks. It is always advisable at this stage to
flush out the system. To do this, open both valves fully and
allow water to flow for approximately 1 minute. This will
remove any foreign matter within the tap body.
7. Finally turn on all the water heating arrangements.
Please note:
Tap heads shown are for illustration
purposes only.
(1)
(2)
(3)
(4)
(5)
(6)
(8)
(7)
(9)
not use any other cleaning materials (even non-scratch type) as these will affect the visible surface.
Do not use abrasive cloths or wire cleaners.
If the cloth used to clean the tap has previously been used with a cleaner that contains bleach ,
take special care to thoroughly rinse the cloth with clean water before use.
W INST 24 (Rev. 1.2)
Wickes Building Supplies LTD
Lodge Way House, Lodge Way
Harlestone Road
Northampton NN5 7UG
Customer service number ：0330 1234 123