Wicksteed Pick-up sticks Sevin User manual

PAGE OF1 4
Wicksteed Leisure Ltd, Digby Street, Kettering, Northants NN16 8YJ Tel: [phone] Fax: [phone]
www.wicksteed.co.uk E:[email protected]o.uk
No part of this document may be copied or used without the express written permission of WICKSTEED LEISURE LTD (c) 2013
FFH
SIZE
AGE RANGE
PROD. CODE
TECHNICAL DATA
MINIMUM SPACE REQUIRED
SUPERVISED PLAY
EQUIPMENT TYPE
LARGEST PART
RECOMMENDED
HEAVIEST PART
INSTALLATION DETAILS
1. READ INSTALLATION INSTRUCTIONS THROUGHLY BEFORE COMMENCING INSTALLATION OF UNIT
2. EXCAVATE FOUNDATIONS USING THE DETAIL AS SHOWN ON PAGE 2 OF THIS DOCUMENT
3. ENSURE TO CHECK AND TIGHTEN ALL FIXINGS USING PROTECTIVE CAPS WHERE NECESSARY
4. BACKFILL FOUNDATIONS WITH CUBIC M CONCRETE ALLOWING TO SET FOR 48 HOURS
5. REMOVE ALL ASSEMBLY AIDS BEFORE THE EQUIPMENT IS USED
THIS PRODUCT CONFORMS WITH BS EN1176- :2008
Version:
Date:
ACTION AND ADVENTURE
PICK UP STICKS 'SEVEN'
PICUS7
L: 6.84M W: 7.82M H: 2.4M
1.8M
7+ YEARS OLD
9.75M X 10.94M
HIGH LEVEL
4.6M X 0.125
34KG (POST 012)
0.096
1
A
09/08/13

PAGE OF2 4
ALL FOUNDATIONS ARE 400 X 400 X 700 DEEP
FOUNDATION PLAN
(1:50@A4)
2150.02850.0
2429.9
1600.0 2150.0
2104.0 1894.0 1767.0
1075.0
1075.0
2505.0
2766.0
2857.0
275.0
275.0
3129.0
3092.0 2825.0
2665.0

PAGE OF3 4
SCALE 1:60@A4
9567.7
10941.1
1587.2
1602.8
1120.3
1500.2
1500.2
1705.4
1547.2
1550.0
72.6 SQ METRES WETPOUR SURFACING
34.5 LINEAR METRES WETPOUR EDGING
MINIMUM SPACE

PAGE OF4 4
10000.0
11500.0
1749.8
2025.0
1711.1
2320.4
2487.9
62 GRASS SAVER TILES (1.5M X 1.0M)
MINIMUM SPACE

PAGE OF1 10
Wicksteed Leisure Limited, Digby Street, Kettering, Northamptonshire NN16 8YJ Tel: [phone] Fax: [phone] http://www.wicksteed.co.uk Email:[email protected]
No part of this document may be copied or used without the express written permission of WICKSTEED LEISURE LIMITED (c) 2012
3rd Angle
Projection
Date:
Drawn By:
Drawing Number:
Sheet:
Issue Date:
Sign:
Issue:Code:
High Level Pick Up Sticks Seven Installation/Assembly PICUS
PICUS7
PICUS7-IN-AY
AK
OF
110
12/08/13
Parts List
ITEM QTY PART NUMBER DESCRIPTION
1 1 FRTB00803 PICUS7 TIMBER SET
2 1 FRMS00804 PICUS7 ROPE SET
3 1 FRMT00801 PICUS8/12 GROUND ANCHOR
4 16 M12X180CHS M12 x 180 CHS
52 M12X230CB M12 x 230 Coach Bolt
Parts List
ITEM QTY PART NUMBER DESCRIPTION
6 21 M12X260CB M12 x 260 Coach Bolt
761 M12WASH 1/2" X 1 1/4" 12G WASHER
845 M12NYLOC M12 NYLOC NUT
9 61 PLC480DCAP GREEN POLY CAP 48
POST LABELS
(REFER TO TIMBER DRAWING FRTB00803)
EQUIPMENT NEEDED
n 13 AUGER DRILL BIT
n 8 DRILL BIT
NOTE: READ INSTRUCTIONS THOROUGHLY BEFORE COMMENCING INSTALLATION OF UNIT
004
003
002
001
007
005
006
008
010
009
12/08/13
A
AK
B
13/11/13
AK

PAGE OF2 10
010
009
006
005
003
002
012
011
SURFACE LEVEL
POST ASSEMBLY & INSTALLATION
Excavate the foundations as detailed using sheet PICUS7-SPEC. Posts labelled 002,003,005 & 006 on this part of the unit should all be leaning at a 10
~
angle away from posts 009 & 010. All posts should all be pre-drilled and of the correct location to achieve this angle. Ensure all bolts are loosely fitted to
give enough movement for ropes and timbers to have the appropriate tensioning.
To use as a starting point, prop and concete posts 009 & 010 into the corresponding foundation holes ensuring the posts are rotated correctly to aid with
later stages of this installation. Prop posts 003 & 006 into the foundation holes. As illustrated below add the horizontal post 012 through the uprights and
secure to posts 003 & 006 using the supplied Coach Bolts. With the two posts secured use another Coach Bolt to secure post 012 to center post 010.
(posts 009 & 010 do not have a pre-drilled hole to secure post 011 & 012 so this will need to be pre-drilled prior to securing with a Coach Bolt)
Repeat this step for 002, 005, 009 & 011.
006
005
003
002
011
012
Note: Use the dimesions below to ensure the correct height is being obtained and the correct pre-drilled holes are being utilised
80.0°
1540.0
1944.0
629.5
650.0
6
9
7
8
6
7
89

PAGE OF3 10
Create stability to the two frames created on page 2 by adding the horizontal timbers pictured below. First, attach horizontal timber 014 to the two
uprights 005 & 006 using the supplied Coach Bolts. (Timber 014 will have a hanging net attachment later on in this instruction so ensure the double
counterbores are positioned in the correct places). Use the below diagram to position post 014 into the correct pre-drilled hole.
SURFACE LEVEL
With post 014 positioned in place, start to position and secure 6 x post 021 into place using the supplied Coach Screws. NOTE: Posts 011 & 012 do not
have pre-drilled pilot holes so before securing with a Coach Screw, create a 8mm pilot hole to prevent the timber from splitting.
Use the dimensions on page 4 to position, mark and pilot hole posts 021 onto posts 011 & 012.
012
003
002
011
009
010
006
005
013
014
1726.0

PAGE OF4 10
006 005
014
013
012
011
NOTE: Use dimensions to measure parallel to posts 011 & 012
950.0
400.0
700.0
800.0
750.0
460.0
650.0
700.0
400.0
1100.0
450.0
820.0

PAGE OF5 10
1465
Prop posts labelled 004 & 008 into the foundation holes. Using the dimensions below, secure post 015 to posts 004 & 008 using the supplied Coach Bolts
into the pre-drilled holes. Again, using the reference dimensions below, secure post labelled 016 to the upright 004 with the other end resting on angled
timber 012. Secure to post 004 using the supplied Coach Bolt.
As illustrated, with the other end approx 1465mm from the end of post 012, mark and drill a n 8mm pilot hole. Re-position post 016 and secure to post
012 using the supplied Coach Screw. NOTE: Ensure a pilot hole has been drilled to prevent timber splitting.
SURFACE LEVEL
013
011
012
016
015
004
008
479
6789
220.0480.0
588.5
004
008
015
016
012
REFERENCE DIMENSIONS
NOTE: Use dimension to measure parallel to post 012

PAGE OF6 10
003
017
Use the pre-drilled hole to position post labelled 017 against upright 008 and loosely secure using the supplied Coach Bolt. Ensure post 017 runs on the
underside of post 016 and up against post labelled 003. Mark the hole position on 003 and remove post 017. Drill a n 13 hole through post 003, re-position
post 017 and secure with the supplied Coach Bolt.
The point at which post 016 rests on post 017 use the pre-driled counterbore hole in 016 to mark a hole and drill a n 8mm pilot hole into post 017. Secure
both posts together using the supplied Coach Screw.
SURFACE LEVEL
008 006
018
016
MARK & DRILL n 13 HOLE
6789
47
9
017 018
006
003
017
838.5550.0
250.01250.0
REFERENCE DIMENSIONS