Wildfire WF-DBLSBRN-RH Quick start guide

IMPORTANT: Read all instructions and warnings before using this product! Use of this product, as with any
similar outdoor side burner, will involve risks from high temperatures and from exposure to smoke and
fumes. Please exercise caution and common sense.
To installer or person assembling Side burner: Leave this manual with Side burner for future reference.
To consumer: Keep this manual for future reference as it contains important Warnings and Instructions.
Conforms to ANSI STD Z21.58-2018
Certied to CSA STD 1.6-2018
Outdoor Cooking Gas Appliance
FOR OUTDOOR USE ONLY
052022_V1
AFFIX SERIAL NUMBER
LABEL HERE

1
Welcome to Wildre Outdoor Living
Please read this manual carefully to understand all the instructions about how to install, operate and
maintain your side burner for your safety and for optimum performance and longevity. We know you’ll
enjoy your new side burner and thank you for choosing our product. We hope you consider us for
future purchases.
Read and save the instructions
Obey all Warnings and Instructions.
This Manual provides specic operating instructions for your model. Use your side burner only as
instructed in this manual. These instructions are not meant to cover every possible condition and
situation that may occur. Common sense and caution must be practiced when installing, operating
and maintaining any appliance. If you lose this Manual, a replacement copy can be downloaded from
our website at www.wildreoutdoorliving.com or call Customer Service at 602-344-4840.
Slide-In Side burner
WF-DBLSBRN-RH

2
Table of Contents & Critical
Safety Warnings
General Safety Instructions .................... 3
Limited Lifetime Warranty....................... 5
Side burner Models ................................ 6
Locating the Side burner ........................ 7
Gas Requirements................................ 11
Liquid Propane Gas Supply.................. 12
Natural Gas Supply .............................. 16
Operating the Side Burner.................... 18
Lighting Your Side Burner..................... 19
Using Your Side Burnering Safely ........ 20
Care & Maintenance............................. 21
Troubleshooting Your Side Burner........ 24
Exploded Parts View ............................ 27
Parts Listings........................................ 28
DANGER
IF YOU SMELL GAS:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. Open Lid.
4. If odor continues, keep away from the
appliance and immediately call your gas
supplier or your re department.
WARNING
WARNING:
1. DO NOT store or use gasoline or other
ammable liquids or vapors in the vicinity
of this or any other appliance.
2. A Liquid Propane (LP) cylinder not con-
nected for use shall not be stored in the
vicinity of this or any other appliance.
FOR OUTDOOR USE ONLY:
NEVER operate side burner in enclosed
areas, as this could lead to gas accumu-
lating from a leak, causing an explosion
or a carbon monoxide buildup which will
result in injury or death.
DO NOT use your side burner in garages,
breezeways, sheds or any enclosed area.
NOT FOR USE BY CHILDREN. If these
instructions are ignored, a hazardous re
or explosion could result in physical injury,
death or property damage!
DANGER
WARNING
CAUTION
DANGER means if the danger is not avoided.
It will cause death or serious injury.
WARNING means if the warning is not heeded.
It can cause death or serious injury.
CAUTION means if the precaution is not taken.
It can cause minor or moderate injury or prop-
erty damage.
DANGER

3
Important Warnings and Safety Instructions
CAUTION
Improper installation, adjustment, alteration, service, maintenance or use can cause injury or
property damage. Read the installation, operating and maintenance instructions thoroughly
before installation or servicing of this equipment.
1. For Outdoor Use Only.
2. Wildre side burners are only intended for residen-
tial use and are not intended for commercial use,
where anyone other than the original purchaser
(homeowner) would be using and maintaining the
Side burner.
3. NEVER use indoors or in any type of enclosed
area, such as a garage, shed or breezeway. Keep
clear of trees and shrubs. The side burners are not
intended for installation in or on recreational vehi-
cles, portable trailers, boats or any other moving
installation.
4. To reduce the risk of serious or fatal injury from
breathing toxic fumes and from explosion and re
as a result of leaking gas, use only outdoors in an
open area with good ventilation. NEVER obstruct
the ow of combustion and ventilation air.
5. Fire Hazard: The area surrounding your new Side
burner should be kept clean and free from amma-
ble liquids and other combustible materials such
as mops, rags or brooms, as well as solvents,
cleaning uids, lighter uid and gasoline.
6. NEVER use the side burner in windy conditions.
If located in a consistently windy area (oceanfront,
mountaintop, etc.), a wind break is
required. Always adhere to the clearances. Spec-
ied on the "Locating the Side burner" section of
this manual.
7. NEVER leave the side burner unattended while
cooking.
8. Risk of Explosion: NEVER use natural gas in a
unit designed for liquid propane gas or vice versa.
9. Do not use lighter uid in/on a gas side burner.
10. NEVER allow children to use or play near the side
burner. Keep children and pets away from a hot
side burner at all times
11. Installation and any repairs or replacement of
parts should be performed by a qualied service
technician. If you are not qualied to install, repair,
or replace parts of your side burner, please retain
a qualied professional contractor or technician to
do so.
12. Burn Hazard: NEVER lean over an open side
burner. Do not place clothing or other ammable
material on or near the side burner. Do not wear
loose-tting clothes or long sleeves while using the
side burner as some fabrics can be highly amma-
ble and, if ignited, may result in personal injury or
death.
13. Burn Hazard: When using the side burner, do
not touch the side burner rack, burner grate, or
immediate surroundings as these areas become
extremely hot and can cause burns. Always use
a covered/gloved hand when opening the Side
burner hood and only do so slowly to allow heat
and steam to escape.
14. ALWAYS: have an ABC re extinguisher
accessible.
15. NEVER attempt to extinguish a grease re with
water or other liquids as this may cause a ash-
back that could result in personal injury or death.
16. NEVER use aluminum foil to line the side burner
racks or the drip trays, this can alter airow for
proper combustion and also build up heat in the
control area causing damage to the knobs.
17. NEVER allow grease or other hot material to drip
from the side burner onto the valve, hose,
or regulator. If that occurs, turn off the fuel supply
immediately. After the side burner has cooled,
determine the cause of the dripping and correct
it. After cleaning the valve, hose and regulator,
perform a soapy water leak test before continuing
use. If a leak is discovered, call a qualied techni-
cian for service.
General Safety Instructions

4
18. NEVER heat any unopened glass or metal
container of food on the side burner. Pressure
may build up and cause the container to burst,
possibly resulting in death, serious personal inju-
ry, or property damage.
19. ALWAYS: Keep any electrical supply cords away
from water or heated surfaces. Electrical cords
should be placed away from walkways to avoid
tripping hazard.
20. ALWAYS: Keep gas supply lines as short as
possible.
21. NEVER move the side burner when hot.
22. NEVER use side burner while under the inu-
ence of drugs or alcohol.
23. NEVER store a spare gas cylinder under or near
your side burner.
24. Fire Hazard: NEVER side burner without the drip
tray in place; hot grease could leak downward
and produce a re or an explosion. Drip tray
should be pushed all the way to the rack located
just under the side burner.
25. Fire Hazard: Grease is extremely ammable.
Let hot grease cool down before attempting to
handle or dispose of it. After use and cool-down,
the drip tray should be cleaned on a regular
basis and kept free of grease.
26. In the event that a burner goes out, turn burner
knobs to the full OFF position, fully open the side
burner hood and let it air out. NEVER attempt to
use the Side burner until the gas has had time to
dissipate.
27. Do not use a side burner until a leak check has
been completed.
28. ALWAYS: Turn off the LP cylinder tank valve
when your side burner is not in use.
29. ALWAYS: Ensure the control knobs are in the
"OFF" position when not in use.
30. ALWAYS: Use only a Ground Fault Interrupter
(GFI) protected circuit with this outdoor cooking
gas appliance.
General Safety Instructions (continued)
DO NOT RELY JUST ON THIS SAFETY SECTION. USE CAUTION AND COMMON SENSE AT ALL TIMES.
PLEASE READ THE REST OF THIS MANUAL CAREFULLY FOR OTHER IMPORTANT SAFETY WARNINGS.
WARNING
CALIFORNIA PROPOSITION 65 - WARNING: The burning of gas cooking fuels (propane gas) generates
some byproducts (including Benzene) which are on the list of substances which are known by the State of
California to cause cancer (birth defects) or reproductive harm. California law requires businesses to warn
customers of potential exposure to such substances. To minimize exposure to these substances, always
operate this unit according to the Use and Care Manual, ensuring you provide good ventilation when
cooking with gas.

5
Limited Lifetime Warranty
TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS LIMITED LIFETIME WARRANTY AND THE
REMEDIES SET FORTH BELOW ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. TO THE
MAXIMUM EXTENT PERMITTED BY LAW, WILDFIRE OUTDOOR LIVING ALSO SPECIFICALLY
DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION,
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
WILDFIRE OUTDOOR LIVING PRODUCTS LIMITED LIFETIME WARRANTY –Wildre Outdoor Living
warrants to the original purchaser at the original site of delivery with proof of purchase of each Outdoor
Gas side burner/side burner that when subject to normal residential use, it is free from defects in work-
manship and materials for the periods specied below. This warranty excludes Side burners used in
rental and commercial applications. This warranty excludes surface corrosion, scratches and discolor-
ation which may occur during normal use. It does NOT cover labor or labor related charges. There will
be shipping and handling charge for the delivery of the warranty part(s).
This product has a limited lifetime warranty that starts at date of purchase and continues throughout the
life of the product.
Under this warranty, Wildre has the option to repair or replace any defective part of the product during
the warranty period. This warranty does not cover normal wear of parts, damage resulting from any of
the following: negligent use or misuse of the product, use on improper fuel/gas supply, use contrary to
operating instructions, or alteration by any person other than a factory service center. The warranty peri-
od is not extended by such repair or replacement.
WARRANTY CLAIM PROCEDURE: If you require service or parts for your Wildre side burners, please
contact our Warranty Service Center for factory direct assistance. Our hours of operation are 8 am to
4:30 pm MST. The phone number is 602-344-4840 and the email address is support@wildreoout-
doorliving.com. Please have your model number, serial number and proof of purchase available for
any warranty claim.
Wildre Outdoor Living may require the return of defective parts for examination before issuing replace-
ment parts. If you are required to return defective parts, shipping charges must be prepaid by the
customer. Upon examination and to Wildre Outdoor determination, if the original part is proven defec-
tive, Wildre Outdoor Living may approve your claim and elect to replace such parts without charge. In
every instance, the customer is responsible for shipping and handling of replacement parts. Component
repair or replacement is the exclusive remedy under this limited warranty and Wildre Outdoor Living
shall not be liable for any incidental or consequential damages.

6
Slide-In Side burner Models
Product BTU/HR Knob Electric
Model No. Width (Front/Back) Burner(s) Lights Required
W x D x H
WF-DBLSBRN-RH 14" x 23-1/2" x 10-1/2" 15,000/15,000 2 Burners Yes Yes - Qty 1
* Each burner is capable of producing up to 12,000 BTUs. Each side burner has been optimized for fuel efciency and
cooking performance. Please contact Wildre Customer Service for additional information on BTU output.
Slide-In Side burner
WF-DBLSBRN-RH

7
Locating the Side burner
Check your local building codes for the proper method of installation. In the absence of local
codes, this unit should be installed in accordance with the National Fuel Gas Code No. Z223.
1-1998 USA or CAN/CGA-B149.1/.2 Natural Gas/Propane Code (Canada) latest edition or the
National Electrical Code ANSI/NFPA No. 70 or the Canadian Electrical Code CSA C22.1, 1990
or latest version.
• Before installing built-in side burners in enclosures, copy all product information such as model number,
serial number and type of side burner (e.g. natural gas or LP) and store information in a safe place.
• If the side burner is installed by a professional installer or technician, be sure that he or she shows you
where your gas supply shut-off is located. All gas lines must have a shut-off that is readily and easily ac-
cessible. If you smell gas, check for gas leaks immediately. Check only with a soap and water solution.
Never check for gas leaks with an open ame.
Notice: We strongly recommend professional installation of your WILDFIRE side burner. These instructions
provide the measurements necessary to construct a masonry structure to house your outdoor gas Side
burner.
IMPORTANT: Gas ttings, regulator, and installer supplied shut-off valves must be easily accessible.
LOCATION OF YOUR side burner:
Locate the side burner only OUTSide in a well-ventilated area. Never locate the side burner in a building,
garage, breezeway, shed or other such enclosed areas without an approved ventilation system. When
in use, the side burner will generate a lot of smoke. When installing your side burner, select an outdoor
location that will ensure there is adequate area for the smoke to dissipate IN ORDER TO AVOID INHA-
LATION OF POTENTIALLY TOXIC FUMES.
Ventilation Requirements for Proper Operation of your Wildre side burner
• Ventilation for a gas side burner is absolutely mandatory to ensure that your side burner performs as in-
tended and to ensure the safety of you, your family, and guests. Proper ventilation is necessary to allow
heat inside your side burner to escape and also to allow any gas that has leaked from a tank or connec-
tion to escape before a buildup of such gas can occur and possibly ignite.
Failure to provide proper ventilation cause a risk of bodily injury or death.
• If you elect to install your side burner into an island, the island itself must be ventilated properly. Any
such island must have a minimum of 2 vents (but optimally 4 vents) per cabinet that has any sort of gas
supply or connection. Each vent must be at least 20 sq. in in size and have access to outside/fresh air.
Those vents will allow heat that is trapped inside due to wind to be able to dissipate out of the island
vents. However, if the island is not ventilated properly and the wind is coming from the back, then the
heat will try to escape through the easiest exit, which will most likely be through the bottom of the side
burner and front control panel.

8
• A simple way to think of what is occurring inside your side burner is that when your burners are on, they
are emitting a ame that creates the heat to cook your food. This heat must exhaust or escape from the
Side burner, otherwise you would eventually have a unit that would not only build up intense heat but also
dangerous pressure. This could cause severe damage to not only the sSide burner but any operators or
people or property near-by. The side burner itself allows for ventilation mainly through the rear of the unit
above the rear panel but below the top of the hood. However, wind can act as a barrier to ventilation and
exhaust. This blockage of exhaust can cause problems and hazardous conditions. Therefore, great care
must be taken in selecting a location for your side burner and in the installation of it into any masonry
island or other outdoor structure. This can cause the control panel and knobs to get hot to the touch and
possibly even burn your ngers, not to mention that it can melt all rubber gaskets on the valves and dam-
age the ignition system to where it will need full replacement.
• Ventilation and typical wind direction and conditions must always be considered when planning your out-
door cooking island. Just the same as you would plan the layout and measure your indoor kitchen,
you must also do the same for the outdoors.
.
Clearance:
• FROM NON-COMBUSTIBLE MATERIALS: Wildre side burners can be placed directly on, or adjacent
to, non-combustible materials, subject to ventilation requirements. The hood on a Wildre side burner
pivots mainly on the body. If you have a wall or partition behind the unit that would block ventilation, then
a minimum of 7" clearance from the back of the side burner to the wall is needed for the purpose of venti-
lation. If you do not have a wall or partition blocking the ventilation of the unit, then you only need an extra
2" behind the unit for the hood to open fully. If you wish to use the rotisserie option, you will want to make
sure that you leave adequate space (at least 6") on each side of the Side burner so that the motor and
rotisserie spit handle will have room on the counter, as these extend past the overall dimensions of the
Side burner body.
• FROM COMBUSTIBLE MATERIALS: Wildre Side burners must have at least 24" clearance from any
combustible materials (in any direction) for the safety of the homeowner and for any Wildre Warranty to
remain in effect.
• You CANNOT locate the Side burner under any combustible material without an approved ventilation
system located directly above the unit. To elaborate, Wildre denes an approved ventilation hood as:
• The ventilation hood chosen must be UL certied, produced for outdoor use and must be installed
according to the hood manufacturer’s specications.
• The hood must be installed at least 30" above the top of the cooking surface.
• The hood must be at least 6" wider that the Side burners frame (3" on each side), not just the cooking
surface.
Locating the Side burner

9
For Built-in Installations
A built-in side burner is designed for easy installation into masonry enclosures. For non-combustible applica-
tions, the side burner drops into the opening (as shown in cut-out detail drawing - Fig. A) and hangs from
the side burner body itself. A bottom deck is not required to support the Side burner from the bottom. It is
also required that:
• A minimum of two ventilation holes in the enclosure, of at least 20 sq. inches in size (per vent), must be
present to help release any leaking gas from the enclosure.
• As Propane is heavier than air, for propane Side burners locate your vents at the tank valve height or
lower
• As Natural Gas is lighter than air, for natural gas Side burners locate your vents at the gas connection
height or higher
• The counter should be at and level relative to the oor.
LP TANK STORAGE MUST BE ISOLATED IN A SEPARATE
COMPARTMENT FROM THAT OF THE Side burner AND IT MUST BE
VENTED AS WELL.(RECOMMEND BOTTOM VENTS FOR LP)
The two illustrations demonstrate how the slide-in type unit is designed to t into open- front enclosures, and
supported at the Countertop.
Do not install this unit under unprotected ammable surfaces. Do not install or use this appliance inside a
building, garage, or any other covered area. It must not be used in or on recreational vehicles or boats.
High Elevation Installation and Use
Wildre Side burners are designed to operate most efciently at 0-2000 feet above sea level. From 2000-
4000 feet above sea level you will not notice any substantial decrease in your heat, although more gas is
combusting within the burners due to less oxygen. Above 4000 feet, you may experience longer cooking
times on your side burner than experienced at sea level. This is due to the air/fuel mixture taking place
within the burners. If you have questions or concerns regarding your location or elevation, please contact
Wildre Customer Service for assistance.
Fig. A

10
Minimum of 2 vents, but optimally 4 vents, per cabinet that has any sort of gas supply or connection.
Each vent must be at least 20 sq in in size and have access to outside/fresh air.
Two vents on each side will facilitate and improve airow and ventilation
Model Cutout Dimensions Overall Dimensions Total BTU Ratings Electrical Outlets
Needed (120V)
Side burner Height Width Depth Height Width Depth LP NG Rotisserie Lights
WF-DBLSBRN-RH 10-1/2" 13" 20" 10-1/2" 14" 23-1/2" 30,000 30,000 No Yes

11
Gas Requirements
NOTE: Wildre strongly recommends that a qualied service technician perform
the initial installation and all conversions or modications to the gas supply.
Never attach an unregulated gas line to the appliance. Connection to an unregulated gas
line can cause excessive heat or re and the risk of property damage, bodily injury, or death.
Gas valves are preset at the factory to operate on liquid propane or natural gas.
If you wish to convert, be sure to contact your side burner dealer FIRST!
IMPORTANT: Before connecting your side burner to a gas source, make sure side burner control knobs are
in the "OFF" position.
• Verify the type of gas supply to be used, either natural or liquid propane, and make sure the marking on the
appliance rating label agrees with that of the gas supply. Do not connect a Wildre liquid propane gas Side
burner to a natural gas supply, and do not connect a Wildre natural gas side burner to a liquid propane gas
supply.
• All pipe sealants must be an approved type and resistant to the actions of LP gas. Never use pipe sealant
on are ttings.
• The installation of this appliance must conform with local codes or, in the absence of local codes, with
either National Fuel Gas Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane Installation Code,
CSA B149.1, or Propane Storage and Handling Code, B149.2, or the Standard for Recreational Vehicles,
ANSI A 119.2/ NFPA 1192M, and CSA Z240 RV Series, Recreational Vehicle Code, as applicable.

12
Liquid Propane Gas Supply
Always check the rating plate to make sure gas supply to which you connect the side burner is the gas type for
which the side burner is manufactured. A Wildre liquid propane (LP) gas side burner is designed to operate
on propane gas ONLY, at a pressure regulated at 11" (279.4mm) water column (W.C.) when equipped with the
correct propane orices on the valves and a propane regulator on the supply line regulated at the residential
meter. A Wildre liquid propane gas side burner comes with a propane regulator that is designed to be used
with a standard 20 lb. gas cylinder and those cylinders must be constructed and marked in accordance with
specications of the US Department of Transportation for propane gas cylinders.
• Liquid propane (LP) gas is ammable and hazardous if handled improperly. Know its characteristics
before using any propane products.
• Propane characteristics include: ammable, explosive under pressure, heavier than air and settles
in pools and low areas.
• In its natural state, propane has no odor. For your safety, an odorant typically is added. ALWAYS
purchase or rell your propane tanks from a reputable propane gas supplier.
• Contact with propane can cause freeze burns to the skin.
• NEVER use a propane cylinder with a damaged body, valve, collar or footing.
• A dented or rusted propane cylinder may be hazardous.
• Always keep LP cylinder securely fastened in an upright position.
• Never connect an unregulated propane gas cylinder to the Side burner.
• NEVER subject (expose) propane cylinders to excessive heat.
• Never store an LP gas cylinder inside a building or in the vicinity of any gas-burning appliance.
Cylinder Specications
• Any L.P. gas supply cylinder used with this Side burner must be approximately 12 inches
diameter and 18 inches high. The maximum fuel capacity is 80% and is approximately 20 pounds
of propane.
• The L.P. cylinder must have a shut-off valve (see picture) terminating in a Type 1 L.P.
• A Type 1 compatible cylinder with a Type 1 cylinder valve has a back-check valve which does not
permit gas ow, until a positive seal has been obtained.
• The cylinder must be arranged for vapor withdrawal. It must also include a collar to protect the
cylinder valve. A safety relief device having direct communication with the vapor space of cylinder
must be provided. This will expel high pressure gas if the cylinder is overlled or overheated which
could result in re or explosion.

13
• All L.P. gas cylinders used with this appliance shall be constructed and
marked in accordance with the specications for L.P. gas cylinders of the
U. S. Department of Transportation (DOT) or the National Standard of Can-
ada, CAN/CSA-B339, Cylinders, Spheres and Tubes for Transportation of
Dangerous Goods; and Commission, as applicable; and shall be provided
with a listed overlling prevention device.
• Read labels on the L.P. Gas Supply Cylinder.
• New cylinders are always shipped empty for safety.
• Allow only qualied L.P. gas dealers to ll or repair your L.P. gas
supply cylinder.
• Inform the gas dealer if it is a new or used cylinder to be lled.
• After lling, have the gas dealer check for leaks and to see that the relief valve remains effective and in
good repair.
Hose and Regulator (Comes standard with the Side burner)
The Type 1 connection system has the following features:
• The system will not allow gas to ow until a positive connection has been
made.
The cylinder control valve must be turned off before any connection is
made or removed.
• The system has a thermal element that will shut off the ow of gas in the
event of a re.
• The system has a ow limiting device which, when activated, will limit the
ow of gas to 10 cubic feet per hour.
• NEVER use Side burner without leak testing this connection.
LP (Propane) Gas Supply Connection
1. The tank valve should be in the "OFF" position. If not,
turn the knob clockwise until it stops.
2. Make sure all burner valves are in the "OFF" position.
3. Always connect the gas supply regulator as follows:
Insert the regulator inlet into the tank valve and turn the coupling nut clockwise until the coupler tightens
up (see Figure 1). Do not over-tighten the coupler. Turn the main tank valve on, and turn the burner con-
trol valves on the unit to the "HIGH" position for about 20 seconds to allow the air in the system to purge
before attempting to light the burners.

14
Pre-Operation Leak Testing
1. Do not insert any tool into the valve outlet or safety relief valve. You may damage the valve and cause
a leak. Leaking propane may result in explosion, re, severe personal injury, or death.
2. If a leak is detected at any time, or you cannot stop a gas leak, immediately close the tank’s shut-off valve
(gas supply from LP tank to the Side burner) and call LP gas supplier or your re department!
3. Check all gas supply ttings before each use and each time the gas supply cylinder is connected to the
regulator. Have a qualied service technician leak test the Side burner any time a part of the gas system
is replaced.
Never attempt to attach this Side burner to the self-contained LP gas system. Do not use the Side burner until
leak testing has been completed.
Leak Testing Valves, Hose and Regulator
1. NEVER smoke while leak testing.
2. Extinguish all open ames. Never leak test with an open ame.
3. Mix a solution of mild detergent or liquid soap and water.
4. Turn all Side burner control knobs to OFF.
5. Ensure that the connections from the regulator to the Side burner
and tank are tight and secure (Figure A).
6. Completely open LP tank valve by turning cylinder valve knob
counterclockwise. If you hear a rushing sound, turn gas off
immediately. There is a major leak at the connection.
Correct before proceeding by calling the Wildre Customer Service line at 602-344-4840.
7. If no rushing sound, brush soapy solution onto areas where bubbles are shown in LP tank (Figure 2).
8. If "growing" bubbles appear, there is a leak. Close LP tank valve immediately and retighten connections.
If leaks cannot be stopped, do not try to repair the regulator, or tank valve, by yourself and contact the
Wildre Customer Service line at 602-344-4840.
9. Always close LP tank valve after performing leak test by turning cylinder valve knob clockwise.
NOTE: When leak testing this appliance, make sure to test and tighten all loose connections. A slight leak in
the system can result in a low ame, or a hazardous condition that could result in a re or explosion.

15
LP Gas Supply Cylinder Disconnection
In order to disconnect the LP tank from the side burner:
1. Turn the burner valves off.
2. Turn the tank valve off. (Turn shut-off clockwise to stop).
3. Detach the regulator assembly from the tank valve by turning the quick coupling nut counterclockwise.
LP Tank Removal, Transport and Storage
• Turn OFF all control knobs and LP tank valve. Turn coupling nut counterclockwise by hand only - do not
use tools to disconnect.
Install safety cap onto LP tank valve. Always use cap and strap
supplied with valve.
Failure to use safety cap as directed may result in serious
personal injury and/or property damage.
A disconnected LP tank in storage or being transported must have
a safety cap installed (Figure 3).
• Never leave a LP tank inside a motor vehicle. (Heating of the vehicle
could cause an increase in the gas pressure which may open the
release vale allowing gas to escape resulting a serious risk of re
or explosion.)
• Do not store an LP tank in enclosed spaces such as a store room, garage, shed, covered patio or
other building.
• Do not store LP tank in an area where children play.
LP Tank Filling
• Use only licensed and experienced LP dealers.
• LP dealer must purge tank before lling.
• Dealer should NEVER ll LP tank more than 80% of LP tank volume. Volume of propane in tank will vary
by temperature.
• A frosty regulator indicates gas overll. If frosty, immediately close LP tank valve and call local LP gas
dealer for assistance.
• Do not release liquid propane (LP) gas into the atmosphere. This is a hazardous practice.
• To remove gas from LP tank, contact an LP dealer or call a local re department for assistance.
LP Tank Exchange
• Exchange your Type 1 cylinder for OPD safety feature-equipped replacement tank ONLY.
• Always keep new and exchanged LP tanks in upright position during use, transit or storage. Leak test new
and exchanged LP tanks BEFORE connecting to Side burner.

16
Large Capacity Propane Tanks and Homes:
If your entire house is plumbed for propane gas use, and you have an exterior connection for such use, then a
standard LP Side burner from Wildre can be connected to such outdoor propane connection, but you must be
aware of the following:
o Wildre does not supply any gas ttings or lines, other than the regulator needed within the side burner
box.
o All Wildre LP side burners come with a 20lb tank regulator. This regulator cannot be used or modied to
work on any other setup.
o If you are running off of a large capacity tank (more than 20lbs), then an "in-line" LP regulator is needed,
which can be purchased from any Wildre authorized dealer or plumbing supply company. However, it is
the responsibility of the owner/installer to verify that the correct regulator is purchased for the intended
application and that it is installed properly.
o As codes vary from state to state, it is the responsibility of the owner/installer to ensure that all county,
state and federal codes are followed for any gas installation.
NATURAL GAS SUPPLY
Always check the rating plate to make sure the gas supply to which you connect the Side burner is the gas
type the side burner is manufactured for.
A Wildre natural gas (NG) side burner is designed to operate on natural gas ONLY, at a pressure regulated
at 4" (101.6mm) water column (W.C.) when equipped with the correct natural gas orices on the valves
and a natural gas regulator on the supply line regulated at the residential meter.
Never connect the Side burner to an unregulated gas supply.
NATURAL GAS CONNECTIONS MUST BE PERFORMED BY A LICENSED
CONTRACTOR OR LOCAL GAS COMPANY REPRESENTATIVE.
Natural Gas Regulator
NEVER use Side burner without leak testing this connection.
Natural gas regulator model: GR120
Gas pressure: 4" (101.6mm)
Maximum rate working pressure: 1/2 Psig

17
Leak Testing Valves, Hose and Regulator
1. NEVER smoke while leak testing.
2. Extinguish all open ames. Never leak test with an open ame.
3. Mix a solution of mild detergent or liquid soap and water.
4. Turn all Side burner control knobs to OFF.
5. Ensure the connections from the regulator to the side burner and tank are tight and secure.
6. Completely open the shut-off valve. If you hear a rushing sound, turn gas off immediately.
There is a major leak at the connection. Correct before proceeding by calling the
Wildre Customer Service line at 602-344-4840.
7. If no rushing sound, brush soapy solution onto all connection points.
8. If "growing" bubbles appear, there is a leak. Close the shut-off valve immediately and retighten connec-
tions. If leaks cannot be stopped, do not try to repair the regulator, or shut-off valve, by yourself and con-
tact the Wildre Customer Service line at 602-344-4840.
NOTE: When leak testing this appliance, make sure to test and tighten all loose connections. A slight leak in
the system can result in a low ame, or a hazardous condition that could result in a re or explosion.
Natural Gas Supply and Connection
1. Make sure all burner valves are in the "OFF" position
2. All NG units need to have a regulator and shut-off valve on the supply line.
3. All Pipe threads need to have proper, gas-rated, outdoor-rated thread sealant.
Flare ends do not need or utilize pipe sealant.
4. Your NG Wildre side burner comes with a ½" pressure regulator, nd gas hose with NG pressure
regulator on rear of Side burner.
a) Attach connection hose (not included) to the side of the NG regulator (it is also ½" MIP)
i. We suggest using ½" stainless steel corrugated hoses for all NG Side burners
ii. Make sure that you purchase a hose of adequate length and capacity for the intended application.
b) Connect the other end of this hose to shut-off valve at the gas source.
i. Depending on your choice of hose and shut-off, the nipple going into the shut-off valve may vary.
c) Test all connections for leaks with a soap and water solution.
Wildre is not responsible for the selection or performance of the contractor or
installer who performs the connection of the natural gas supply to the side
burner.
1. Transformer for LED Lights - Your side burner’s electrical transformer will
connect on the left side of your side burner (looking at it from the front) and
operates the LED lights. Follow the pictures and insert the white male plug
into the white female socket, on the left side of your side burner and then
plug the transformer into a standard 110v outlet. If you have any questions
or concerns, please consult or use a qualied electrician.

18
Operating the Side burner
• Failure to open the lid prior to igniting the barbecue’s burners, or not waiting 5 minutes to
allow the gas to clear if the barbecue does not light, may result in an explosive ame-up
which can cause serious bodily injury or death.
NEVER leave the side burner unattended while cooking!
• Check that the end of each burner tube is properly located over each valve orice.
• Light the side burner burners using the instructions provided in this manual.
• Adjust heat settings to your desired cooking temperature.
• Allow side burner to cool down, wipe off any splatters or grease and clean the drip tray.
• NEVER put a cover on the side burner while it is still hot as it could start a re.
GENERAL RULES
Keep any electrical supply cords and the fuel supply hose
away from any heated surfaces.

19
Lighting Instructions for your Gas Side Burner
Using the side burner’s Built-In Ignition System:
1. Open the canopy.
2. Keep your body, arms and face as far away from the
burners and cooking surface as possible.
3. Select the burner that you want to ignite. Depress and
rotate the knob corresponding to that burner counter-clock-
wise to the "High" position.
a. As you are nearing the "High" position, you will
notice the valve getting tougher to turn. This is
the spring inside the valve building up energy to create
the spark. Once you hear a click, the igniter has
red the spark for that burner.
b. Do not turn the knob too fast, as you need the gas to
travel into your manifold, then to the valve and nally into the burner where it will meet the spark from
the igniter (at the front of the burner). Conversely, if you turn the knob too slowly, you can cause a
build-up of gas in the side burner and create a large ash when it ignites.
4. If the burner does not ignite on the rst attempt, try again immediately but be very aware of any gas
building up inside the side burner.
a. If the side burner does not light after three consecutive attempts, turn the knob to the "Off" position,
keep the canopy open, and allow the side burner to clear of any built-up gas for at least 5 minutes
before starting the process again.
5. If at this point the side burner will still not ignite, contact Wildre Customer Service at 602-344-4840, for
further assistance to troubleshoot your side burner.