Wilkening Fireplace The GranView User manual

2
Installation
and Operation
Instructions
Keep these
instructions for
future use
GranView
Clean Burning Zero Clearance Fireplace
The
800-367-7976 wilkeningreplace.com 9608 State 371 NW
Walker, MN 56484

2
Table of Contents
Before You Begin Installation.............................................................................................................................................3
Clearances and Mantel Height Requirements.................................................................................................................... 4
Locating Your Fireplace .....................................................................................................................................................5
Hearth Requirements........................................................................................................................................................5
Chimney Height, Oset and Clearance Requirements....................................................................................................... 6
Combustion Air Requirements...........................................................................................................................................7
Framing Specications ..................................................................................................................................................... 8
Mobile Home Installation Requirements........................................................................................................................... 8
Doors for the GranView ................................................................................................................................................... 9
Heated Air Ducting Options............................................................................................................................................. 9
Clean Face Kit.................................................................................................................................................................10
Facing.............................................................................................................................................................................10
Blower Installation and Electric Wiring Diagram ...............................................................................................................11
Unit Diagrams ........................................................................................................................................................... 12-15
Installing the Refractory Liner and Bae .........................................................................................................................16
Installation Steps ............................................................................................................................................................ 17
Care and Maintenance .................................................................................................................................................... 17
Generating Maximum Heat Output.................................................................................................................................19
Refueling Your Fireplace.................................................................................................................................................. 19
Troubleshooting............................................................................................................................................................. 20
Starting the Fire............................................................................................................................................................. 20
Combustion Control ...................................................................................................................................................... 20
Negative Pressure in the Home........................................................................................................................................ 21
Important Notices ..........................................................................................................................................................22

3
IMPORTANT SAFETY INSTRUCTIONS
Read this section before you begin installation of
the GranView clean burning replace.
This manual will enable you to make your installation safe, ecient and dependable. Read and understand these
instructions completely before starting the installation.
Do not alter or modify any of the components. Do not obstruct the air circulation vents as over-heating will
result. Any alteration or modication of the replace system or components will void the warranty, listing and approvals
which could result in an unsafe or potentially dangerous installation. Use of this product in an altered installation or
with altered components may result in re, loss of property and loss of life. Keep this manual for future reference.
– Read and follow these safety rules –
1. Before starting installation, read and understand this manual.
Failure to follow instructions will result in an unsafe condition,
malfunction, property damage or loss of life.
2. Check with your local building ocial regarding codes and
permits. If local codes are more restrictive than this manual they
must be followed.
3. This replace must be installed with a chimney system that is
listed in the Chimney Section of this manual.
4. To ensure a safe, ecient re, always check the replace prior
to use for creosote build-up, excessive ash and soot. Clean the
replace and chimney regularly.
5. Use solid wood or processed solid fuel re logs only. Do not use
chemical chimney cleaner, gas logs, gas starters or ame
colorants. Do not use coal or charcoal in this replace unit.
6. Do not connect this appliance to a chimney ue that is serving
another appliance.
7. Never use gasoline, gasoline type lantern fuel, kerosene, lighter
uid or any liquid to “freshen” the re. Keep all such highly com-
bustible liquids well away from the re.
8. Never leave children unattended when there is a re burning in
the replace. It is recommended that each user of this appliance
familiarize themselves with its operation prior to initial use.
9. Allow the replace to cool before performing any service to it.
Always shut o any electrical supply prior to working on the
system. This will eliminate the chance of electrical shock.
10. Wilkening Fireplace Co. is not responsible for any smoking issues
due to inadequate draft or poor burning which results from lack
of combustion air or chimney draw.
11. Wilkening Fireplace Co. does not warrant “smoke free” opera-
tion or are we responsible for inadequate draft caused by me-
chanical systems, construction conditions, inadequate chimney
height, negative pressure or environmental conditions beyond
our control.
12. Do not use any replace insert or other product in conjunction
with this replace that is not specied by Wilkening Fireplace Co.
for use with this replace.
13. Never, under any circumstances, install a replace or chimney
component that is suspect of having been damaged in transit or
handling. When in doubt, contact your dealer.
WARNING: This replace has not been tested for use with a gas log set, either vented or unvented.
To reduce the risk of re or injury, do not install a gas log set into this replace.

4
Clearances, Dimensions and Specications
The GranView clean burning replace is a wood burning, high eciency, heat circulating replace system designed for
minimum clearance to combustible framing material.
The illustrations shown in this manual reect typical installations with minimum dimensions and are designed for framing
reference only. Additional clearance to combustibles is permitted. The actual installation may vary due to individual design
preferences. No matter what the design, always maintain the minimum clearances to combustible materials and follow
these instructions.
This replace has been safety tested and is listed to UL 127-2011 standards by Intertek Testing. This unit may be installed in a
mobile home. Install in accordance to the National Fire Protection Standard for chimneys, replaces and solid fuel burning
appliances, NFPA 211, and in accordance with all state and local building codes. Failure to follow these instructions or adapt
parts for use with this unit that are not intended will create a re hazard and will void your warranty.
Clearances and Height Requirements
The GranView may be placed directly on wood ooring – all carpet or vinyl must be removed. The outside air kit, re stop
spacer and roof ashings may be placed directly on or next to normal construction materials.
The minimum recommended interior chase width is 55”. The minimum chase depth is 24”. The interior chase
height must be a minimum of 72” from the replace base for any front louver heat vented application and 80”
from the unit base for any top vent heat outlet installation.
The chimney requires a minimum 2” clearance to combustibles (consult the chimney mfg. instructions).
A combustible mantle, 8” deep, must be a minimum of 53 ½” above the base that the replace is placed on when the front
heat outlet louver is used for heated air circulation. A 51 ½” mantle height may be used when heated air exits through the
dual top vent kit. Non-combustible mantles may be placed at any height.
If you have any questions regarding this product or installation, call your dealer or Wilkening Fireplace Co. at 800-367-7976.
WARNING: Do not pack or ll the required air spaces with insulation or other material. No material of any
kind is allowed inside the chase area. To insulate the chase, do so between the stud walls behind the sheet rock.
NOTICE:
1. For exterior installations it is recommended that you insulate at least the base, sidewalls and the rst oor
ceiling of the chase to prevent heat loss.
2. Local codes may require a one hour re rating on one or all sides of the re chase. Check with local code
authorities prior to construction.

5
Selecting the Location of Your Fireplace
To determine the best location for your replace, take into consideration the location of windows, doors, adjacent side
walls and the general trac ow pattern of the room, allowing space in front of the replace for a hearth extension and
mantle. Hot air ducts, heat circulation ability of the unit and ducting ability for combustion air must also be considered
when selecting the location. If possible, you should select a location that does not require cutting oor joists or rafters.
In most cases no additional oor support is needed for the replace and facing system weight. Consult your local building
code requirements or a structural engineer to determine if additional support is needed.
If possible, install the replace and chimney on the interior of the structure as it will provide better draft performance. In
areas that experience below 0° Fahrenheit temperatures, the use of an exterior chimney increases the possibility of poor
draft, increased creosote formation and slow starting of the re. Installations which are located low in the house such as the
basement, in combination with an outside chimney, are especially prone to ow reversal on start up.
Hearth Extension Requirements
The GranView can be installed on a raised hearth provided there is a minimum of 72” measured between the replace
base and nished ceiling for front louver heat venting or 80” if using dual or single top vent ducting of heated air. Raised
hearths must extend 16” in front of and 8” to each side of the replace opening. Floor level hearths may have a minimum
of a 16” noncombustible protrusion, but 20” is recommended for extra spark protection along with the 8” side protection.
Installations using the single door option should have noncombustible materials extend out past the foremost swing of the
door whether it is a combination of raised and oor level material or not. This will contain any hot embers that may ride on
the inner channel of the door assembly as it opens.
Cover all combustibles under the hearth area 16” in front of and 2 ½” to each side of the replace with the 48” x
16” Micore provided. This provides thermal protection for the combustibles. Any area outside of this space can have
the hearth materials in direct contact with combustibles.
A spark guard (2-L shaped metal strips) are provided to create spark protection where the hearth framing meets the
replace front. These pieces are 2 ½” x 1 ½” x 48” and are designed to create a barrier for sparks that may penetrate the
hearth to the framing below. The spark guard must be placed 2 ½” under the replace base and extend 2 ½” forward under
the hearth stone. When installing this 2 piece guard, place the rst section on top of the protruding hearth. Next, slide the
second section under the replace, overlapping the vertical return of the lower section. If this unit is installed on a non-
combustible base with no combustibles below the hearth, no spark guard is needed. The room air inlet vent at the base
of the replace must not be obstructed by any hearth material abutting the unit.

6
Chimney Requirements
The GranView requires an 8” diameter chimney. Any factory built chimney listed to UL-103HT may be used. The use of
one brand of chimney is required. Do not mix components from several manufacturers as this may cause a re hazard.
Follow the chimney manufacturers’ specications for installation procedures and components necessary to create a code
complying installation.
NOTE: An anchor plate for the chimney brand selected must be used to adapt the chimney to the unit. Secure
the anchor plate using 4 self tapping metal screws and seal it to the replace using 600 degree RTV silicone.
See the diagram on page 13.
A restop and/or a radiation shield is required at each location where the chimney penetrates combustible materials
except at the roof level where a ashing or chase top is employed. Install and seal a storm collar to the section of chimney
penetrating the ashing to prevent moisture from entering the chimney structure.
The roof penetration must meet the minimum clearance to the chimney just as any other combustible must. Use a roof
support to secure the chimney as it passes through the upper roong system.
A chimney cap is required on all installations to validate the warranty. Do not connect this replace to a chimney that serves
another appliance.
Chimney Height, Oset and Clearance Requirements
The total height of chimney used on this installation must be a minimum of 15’ from the base of the unit to the cap with a
maximum of 36’. The maximum chimney height that is supported by the unit is 12’. Roof supports or other listed supports
must be used for additional height. The chimney must extend at least 2’ higher than any roof or wall that is within 10’ of it
6” minimum
Floor level hearth
16”
8”
16”
8”
53 ½” front vent
51 ½” top vent to
unit base
16”
8”
Z strip for
raised hearth

7
or a minimum of 3’ above a chase top or at roof. If the chimney is exposed more than 6’ above the roof, a roof brace must be
used to secure it in place. Read the chimney manufacturer’s instructions for complete details and specications.
The maximum oset that can be used with this appliance is 30 degree. Use no more than two sets of 30 degree elbows
for the installation. To ease cleaning, elbows should have at least one pipe section between them. Support the elbows as
required by the chimney manufacturer.
The chimney must be enclosed when it is installed in or passing through a living area where combustible material or people
may come in contact with it. This is important to prevent personal injury or a re hazard. Consult the chimney manufacturers
instructions for details and clearances.
All framing material, supports and insulation must maintain a 2” minimum clearance to any portion of the chimney. This
area must not be lled with any material. Failure to maintain the 2” minimum clearance will result in a re hazard. Follow
the chimney manufacturer’s installation instructions and clearance recommendations. Typical minimum framing for 8” 2100
degree HT chimney is 14 ½” x 14 ½”. Consult the manual for the chimney brand selected to verify all dimensions.
When a chimney chase is to have multiple ues in it, it is recommended that their terminations be at least 16” horizontally
apart and 12” vertically apart. This is done to reduce the chance of smoke migrating from one chimney to the other.
The Chase Enclosure
The chase is a framed structure created to encase the replace and chimney system. A chase should be constructed just like
any other wall. Exterior chase construction must be insulated on the sides, back, ceiling and below the base that the replace
sits on. The R value of the chase should be the same as the rest of the walls of the structure. Any insulated chase walls must
be covered with sheetrock or sheeting to contain the insulation.
Combustion Air Requirements
The GranView replace is designed to use outside air to supply each and every combustion air port inside of the replace.
This creates a sealed system for air supply, eliminating replace odor due to negative pressure in the home. The supply
air hook up is located on the lower left of the replace as you face it. A minimum 4” diameter supply pipe is required for
combustion air ducting. If ducting more than ten feet for combustion air, use a 6” pipe and reduce it to 4” at the unit
connection. Do not duct over 25’ for combustion air, or have more than three 90 degree bends in the supply pipe. Do not
terminate the air supply duct in an attic or garage. An insulated class 1 duct must be used to reduce the eect of cold
transfer. To duct 5’ or less use the standard air kit provided with the replace. The standard kit includes a screened exterior
vent termination. Use this termination on the exterior of your structure. Install this duct with an “S” trap to minimize air ow
when the unit is not operating.
Exterior Unit connection
Insulated duct

8
Enclosure Framing
The framing of the replace enclosure must not infringe on the area above the replace unit to ceiling level. The only
combustible material permitted in this space is a header at the front supporting the face above the opening, and this must
not be closer than the metal stand-o.
Framing materials must be at least 1 ½ x 3 ½” covered with sheeting. The minimum nished frame opening is 45 ½”
wide, 51” tall and 24” deep. The frame opening for a top vent kit is 12” wide x 18 ¼” tall each. Normally, framing will be
set back to allow sheeting to be ush with the front of the replace. No framing material may be located above the unit,
except where it contacts the top front unit stand-o. See 13 page for diagrams.
NOTE: If the nished frame opening is created before the replace is in place the unit will not t due to the
combustion air connection. The recommended minimum interior chase size is 55” wide. This will ease the hook
up of the combustion air.
If a raised hearth installation is planned, an elevated platform must be created for the unit to set on and the hearth material
to be installed on. Use the Micore board provided to protect a raised combustible hearth structure or combustibles located
below the nished hearth for oor level installations.
Any part of the frame structure that extends to the outside of the home must be insulated to reduce heat loss.
NOTICE: Under no circumstances can the replace be installed without the clearance spacers in place or with
modied clearance spacers. Do not notch the header or framing to be installed closer than the replace spacers allow.
Side Wall and Mantle Leg/ Side Trim
This appliance must maintain a minimum of a 16” side clearance, measured from the unit to a wall projection. A 6” deep,
maximum, combustible mantle leg or side trim may be place 8” from the unit edge. See diagrams on page 13.
Mobile Home Installation
is replace may be installed in a mobile home. For use in a mobile home the following additional instructions
must be followed to insure a safe installation.
1. WARNING: Do not install this unit in a sleeping room.
2. CAUTION: The structural integrity of the mobile home
oor, wall and ceiling/roof must be maintained.
3. The unit must be permanently secured to the oor of
the mobile home. Bolt the unit in place through the two
metal clips attached to each side of the unit and tighten
securely.

9
Doors for the GranView
Each replace requires a door provided by Wilkening Fireplace Co. to complete the listed unit. To install the door, a heat
resistant gasket and mounting screws are provided in the door carton. Remove the paper backing from the heat resistant
gasket, exposing the adhesive backing. Apply this gasket on the unit face on the outside edge of the predrilled holes
surrounding the replace opening. Use the 8 screws provided in the door carton to attach the metal frame to the unit face.
Do not operate this unit without doors. Do not use any other door with this unit. If your door wears and needs replacement
over time, contact your dealer or Wilkening Fireplace Co. for the appropriate replacement.
Heated Air Ducting Options
The GranView comes standard with a heat outlet at the top of the unit and a room air inlet at the base. Several louver
designs are available to nish these openings. This replace may also have a separate vent or vents, ducted from the pre-cut
holes in the top of the unit, to areas, next to or behind the installation and may be used in conjunction with or without the
vent out the front.
When venting heated air out of the unit front heat outlet vent, a single top vent may be used. If you desire the front vent to
be sealed, dual top vents must be used.
To vent heat from the top of the unit to side or rear chase locations, the top vent kit manufactured by Wilkening Fireplace
Co. must be used. The top vent kit includes two 8” diameter starter rings which attaches the exible insulated vent
to the unit, two grill enclosures with stand-os and two grill covers for the enclosures and a section of 8” insulated
exible aluminum duct. The insulated aluminum duct provided by Wilkening Fireplace Co. must be used for all top vent
applications. A minimum clearance of 6” must remain between the top of the top vent assembly and the nished ceiling.
The bottom of the top vent must be a minimum of 6” above a combustible mantle and at least 6” above the unit top. Never
allow the vent to create a heat trap. Fins on the grill may point up or down.
The dual vents may be run to separate rooms on the side or back of the chase enclosure creating heat outlet in up to three
areas when the front vent is used. Allow adequate return air from remote areas to the room with the replace to assure
proper air circulation. Closeable top vents cannot be used.
An auxiliary heat distribution kit can be attached to the 4” outlet on the back right side of the replace. This kit includes
a 4”-6” adapter, 12’ of 6” class A insulated duct, an inline 150 CFM fan, a grille housing to mount into the framing and a
grille. It can be routed up to 12’ in any direction up, down or to the sides of the replace. The inline fan is mounted directly
behind the grille housing and can be wired to a variable speed control or on/o switch by your electrician. Do not install
the grille into a oor as combustibles may fall through this and cause a re hazard.
4. Use only the outside air kit that comes standard with
the unit. This kit includes one 5’ length of 4” insulat-
ed, ex air pipe, two 4” clamps and one 4” screened
outside air vent.
5. The replace must be electrically grounded to the
frame of the mobile home. Consult and use the
National Electric Code for wiring installation.
6. The chimney shall extend at least 3 feet above the
part of the roof through which it passes. The top of
the chimney is to be at least 2 feet above the highest
required elevation of any part of the mobile home
located with 10’ of the chimney.
7. The ceiling/roof thimble assembly shall extend com-
pletely through the ceiling/roof cavity of the mobile
home to the outermost plane of the roof.

10
Front vent only Front vent with
dual top vents
Dual top vents
No front vent
Front vent with
single top vent
Clean Face Option (See diagram on page 14)
The clean face option allows the elimination of the air inlet louver that is located directly below the doors in the unit
face. Dual 8” exible ducts are connected to the front side of the replace in the pre cut holes. The exible duct
may run up to 6’ down or to the side of the replace. This duct should never run upward. Use part #CFK, which
includes all the parts necessary for this installation. This duct may be run down to the ceiling of a lower area to
enhance circulation of air within the home. When creating a clean face installation, the dual top vent (part #TVK)
must also be ordered to complete the installation. The minimum interior chase framing should be 66” wide if the
exible ducting is routed within the chase. A blower is available to boost air circulation with the clean face option.
It is a variable speed, 210 CFM, 8” round, inline blower. This blower should be located directly behind the inlet vent
housing and attached to the exible plastic duct. Make sure this blower is accessible for service in your installation.
Facing
Combustible material may be installed ush to the exterior sides of the replace face leaving a 3/8” gap. It may
not project in front of or over the steel replace face. A 4” piece of Micore, which is provided, must cover the area
directly above the top of the unit to the header.
Non-combustible materials may be placed across the face of the replace such as brick, stone or tile. Facing kits are
available from your dealer to attach manufactured stone or brick to the face of the replace. See your dealer for the
appropriate one.
To use a manufactured facing product, attach one of the facing kits to the framing structure surrounding the
replace. Do not securely attach this to the replace face as cracking of the mortar may occur due to thermal
expansion of the steel during operation. Self-tapping metal screws may be used to attach the facing kit in several
areas of the steel front taking care not to tighten the screws.

11
NOTE: A tight seal must be created between the metal replace face and the facing material to prevent heat
from owing between them. This seal is typically created by the scratch coat of mortar that is applied over the
facing kit which allows the facing material to bond to it.
When installing sheet rock to the sides of the unit face, leave a 3/8” space between the sheet rock and the metal unit
sides. Caulk the seams surrounding the replace face with a 500 degree RTV silicone or similar material. Failure to leave
this expansion space may cause the sheet rock to crack when the unit expands while heating. Failure to caulk the facing
perimeter may allow heat to ow into the chase area.
Optional Blower Assembly
An onboard blower is available to boost the performance of the heat circulation system when using the lower louver for air
inlet. This blower is a two speed, twin squirrel cage fan. The blower is mounted to the base of the replace, at center, 4”
behind the lower grill using the wing nuts provided in the blower
kit. The blower assembly has two predrilled holes in the plate that
slide over the threaded studs located on the lower heat shield. To
access this area simply remove the lower grill. This will allow free
access to the area below the replace. The wiring diagram depicts
the manner in which the wires are to be connected.
Wire nut all connections.
The heat sensor should be attached to the base of the replace by
sliding it into the slotted bracket located on the far right bottom
of the replace front. Make sure that no wire contacts the steel
surface of the unit as melting of the insulation could occur.
The replace must be grounded through the metal electrical
box located on the right side behind the lower louver. This will
eliminate the risk of electrical shock.
Stone or brick
front
Heavy expanded
metal/stone kit
Plywood or
gypsum
White 110 VAC
Ground
BlackBlack
White
Low/Red
Blue
High/Black
Thermo
disc Terminal
block
Low/o/high switch
Two speed
blower
Internal fan for unit

12
45” to standos
43” unit face
1”
4 ⅝”
3”
18 ¼”
11 3⁄16”
48” 50 ½”
5 ½”
37”
4 ½”
2 ½”
Top stando
24” to stando
8 ¼”
13 ⅛”
21 ½”
8 ¼”
13 ½”
Side stando
4” air supply
8” clean face inlet
9 ¾”
14 ½”
7 ¼”
12 ⅝”
9 ¾”
18”
7 ¼” 4 ½”
Side stando
4” heat duct connection
8” clean face inlet
Electric in
Top stando
Unit Specications
FRONT
LEFT
TOP
RIGHT
45” to standos
43” unit face
1”
4 ⅝”
3”
18 ¼”
11 3⁄16”
48” 50 ½”
5 ½”
37”
4 ½”
2 ½”
Top stando
24” to stando
8 ¼”
13 ⅛”
21 ½”
8 ¼”
13 ½”
Side stando
4” air supply
8” clean face inlet
9 ¾”
14 ½”
7 ¼”
12 ⅝”
9 ¾”
18”
7 ¼” 4 ½”
Side stando
4” heat duct connection
8” clean face inlet
Electric in
Top stando
45” to standos
43” unit face
1”
4 ⅝”
3”
18 ¼”
11 3⁄16”
48” 50 ½”
5 ½”
37”
4 ½”
2 ½”
Top stando
24” to stando
8 ¼”
13 ⅛”
21 ½”
8 ¼”
13 ½”
Side stando
4” air supply
8” clean face inlet
9 ¾”
14 ½”
7 ¼”
12 ⅝”
9 ¾”
18”
7 ¼” 4 ½”
Side stando
4” heat duct connection
8” clean face inlet
Electric in
Top stando
45” to standos
43” unit face
1”
4 ⅝”
3”
18 ¼”
11 3⁄16”
48” 50 ½”
5 ½”
37”
4 ½”
2 ½”
Top stando
24” to stando
8 ¼”
13 ⅛”
21 ½”
8 ¼”
13 ½”
Side stando
4” air supply
8” clean face inlet
9 ¾”
14 ½”
7 ¼”
12 ⅝”
9 ¾”
18”
7 ¼” 4 ½”
Side stando
4” heat duct connection
8” clean face inlet
Electric in
Top stando
45” to standos
43” unit face
1”
4 ⅝”
3”
18 ¼”
11 3⁄16”
48” 50 ½”
5 ½”
37”
4 ½”
2 ½”
Top stando
24” to stando
8 ¼”
13 ⅛”
21 ½”
8 ¼”
13 ½”
Side stando
4” air supply
8” clean face inlet
9 ¾”
14 ½”
7 ¼”
12 ⅝”
9 ¾”
18”
7 ¼” 4 ½”
Side stando
4” heat duct connection
8” clean face inlet
Electric in
Top stando
45” to standos
43” unit face
1”
4 ⅝”
3”
18 ¼”
11 3⁄16”
48” 50 ½”
5 ½”
37”
4 ½”
2 ½”
Top stando
24” to stando
8 ¼”
13 ⅛”
21 ½”
8 ¼”
13 ½”
Side stando
4” air supply
8” clean face inlet
9 ¾”
14 ½”
7 ¼”
12 ⅝”
9 ¾”
18”
7 ¼” 4 ½”
Side stando
4” heat duct connection
8” clean face inlet
Electric in
Top stando
45” to standos
43” unit face
1”
4 ⅝”
3”
18 ¼”
11 3⁄16”
48” 50 ½”
5 ½”
37”
4 ½”
2 ½”
Top stando
24” to stando
8 ¼”
13 ⅛”
21 ½”
8 ¼”
13 ½”
Side stando
4” air supply
8” clean face inlet
9 ¾”
14 ½”
7 ¼”
12 ⅝”
9 ¾”
18”
7 ¼” 4 ½”
Side stando
4” heat duct connection
8” clean face inlet
Electric in
Top stando
45” to standos
43” unit face
1”
4 ⅝”
3”
18 ¼”
11 3⁄16”
48” 50 ½”
5 ½”
37”
4 ½”
2 ½”
Top stando
24” to stando
8 ¼”
13 ⅛”
21 ½”
8 ¼”
13 ½”
Side stando
4” air supply
8” clean face inlet
9 ¾”
14 ½”
7 ¼”
12 ⅝”
9 ¾”
18”
7 ¼” 4 ½”
Side stando
4” heat duct connection
8” clean face inlet
Electric in
Top stando
45” to standos
43” unit face
1”
4 ⅝”
3”
18 ¼”
11 3⁄16”
48” 50 ½”
5 ½”
37”
4 ½”
2 ½”
Top stando
24” to stando
8 ¼”
13 ⅛”
21 ½”
8 ¼”
13 ½”
Side stando
4” air supply
8” clean face inlet
9 ¾”
14 ½”
7 ¼”
12 ⅝”
9 ¾”
18”
7 ¼” 4 ½”
Side stando
4” heat duct connection
8” clean face inlet
Electric in
Top stando

13
51”
12”
Louver
18 ¼”
61 ½”
minimum
with a 4”
tall mantel
that is 8”
deep
72" minimum
chase height
with front
louver,
80" minimum
with top vents
Shown
with
optional
top vent
framing
Finished
frame
opening
45 ½”
6” minimum
to louver
11 ⅞”
11 ⅞”
Louver
55”
Interior chase width recommended
Outside air vent
(Create “S” trap)
Side mantel
leg/trim
16”
6”
16”
8”
2x4 frame
Sheet
Anchor plate
Non-combustible
hearth required
Front framing showing optional top vent requirement
Top view chase framing

14
Lower vents can go to multiple areas or a lower level
ceiling up to 6’ away
Seal this area
Seal this area
Lower vent housing
and louver provided
(part # CFK)
8” plastic ex provided
Use facing kit
(part # CFFK)
Top vents can go to
front, side or back of
the replace chase
Top vent kit
12” minimum if vents are
installed in hearth
Upper steel bae
with holes
Bae support tabs
Bae #7
Air tubes
Angle refractory
(part #5)
62” 16”
Minimum hearth size
92 ½” nished wall size
124 ⅝”
46 ⅛” to unit front
65 ¼” to sheeting
88 ¼”
45° hearth return of 65 ¾”
1” air
space
Clean face illustration
Corner application
Bae placement

15
Center to
center of
chimneys
as shown
36”
59” wide
as shown
Complete chimney as per
manufacturers instructions.
Fire stop radiation shield
shown.
An attic insulation shield
may be required for your
installation. Consult dealer.
NOTICE:
If ducting of outside
combustion air to
the rear of this
chase, add 5” to
total width for this
upstairs replace. If
ducting to the left,
no additional width
is required.
17 inch
oset shown
12” raised hearth shown
12” raised hearth shown
30 degree
no oset
support
shown
Ceiling
96”
Ceiling
12” oor
joist
Floor
96”
63”
Air space to
chimney
Fire stop
radiation shield
Consult chimney
manufacturers
installation
manual for com-
plate information.
Unit stando
shown open to
provide clarity of
oset pipe.
Example of chimney placement when installing two replaces

16
Refractory Liner and Bae Assembly
The GranView utilizes a super reective inner lining of Skamol. These panels protect the metal surfaces and increase the
operating temperature of the burning chamber.
The diagram below shows the placement of this liner and upper baes. Care must be taken when handling these pieces as
not to damage them. Do not operate this unit without all the baes and inner liner in place as overheating of the chimney
connector and replace components may occur.
Once in place, the liner is supported by brackets. If a hair line crack occurs in the liner and it remains in place, it does not
have to be replaced. Replacement of a refractory is necessary if it becomes damaged to the point of falling loose or has gaps
between pieces.
Install the steel bae with holes notched into it in the upper throat of the replace. This bae is placed on the metal
tabs which extend into the upper area, above the secondary combustion air tubes. To install the refractory liner and bae
assembly, install the two upper side refractory panes above
the side air tube rst (part #6) then place the two bottom
refractory pieces (part # 1 & 2) in place. Position the two
piece back panel in place (part #3) using the “U” shaped
stainless steel clip to connect them on the top center edge.
Place the four side pieces in place (part #4) start by sliding
the front ones in position before each back one. Place the
refractory panel (part #5) over the top edge of the air tubes
and slip into place allowing it to rest on the top edge of the
back panel. Position the 2 piece refractory top bae plate
in place on top of the dual stainless steel air tubes. See the
diagrams on page 14 for placement of the refractory and
bae assemblies.
Painted and Plated Surfaces
This appliance is painted with a 1200 degree high heat paint. This paint is an open cell material that allows for heating and
cooling without cracking or chipping. During the rst several res this paint will cure, giving o an odor with some visible
smoke.
Due to the open cell nature of this paint, moisture can impregnate the surface causing rust to form. If this occurs, lightly
sand the surface and repaint with Stove Bright Satin Black paint (#1990) available from your dealer.
Plated surfaces require no polishing to retain their luster. If a plated surface is polished it may remove the plating, exposing
the base materials below. To maintain plated surfaces simply wipe them with a damp, soft, cotton cloth.
Remove all plated nish items and store them in a safe location during installation to ensure that they do not become
damaged. Sheet rock compound will discolor any plated surfaces.
5
6
21
4
3
4
6
4
4
Stainless
“U” Connector
Refractory Liner Placement

17
Installation of the GranView
1. Select the appropriate location for the replace, see page 5.
2. If a raised hearth is used, build the platform for the unit to rest on and frame the structure/chase; cutting or
creating the openings required for air supply, chimney routing, heat dump kit and the top venting option if
needed. See pages 5-9. If insulation is needed in the chase, do so now. Sheet rock must cover any insulated
walls to prevent sagging and contact with the replace unit.
3. Install the outside air assembly into the chase, see page 7.
4. Move the replace into place and connect the outside air supply to the unit. See page 7.
5. Install the chimney using the chimney manufacturers recommended practices and components. See page 6 and
the instructions enclosed with the chimney.
6. Install top vent kit and or clean face components if applicable, see pages 9-10.
7. Remove the lower grill which is magnetically held in place. Route a power supply into the junction box of
the replace for power for the on board blower. All connections and materials must conform to the National
Electric Code. Power requirements are 110VAC with a 10 amp supply. If a blower is added to the installation do
so now, see page 11 for the on board blower. Reinstall the lower grill.
8. Install the doors. See page 9.
9. Finish facing of the replace and hearth area. See page 10-11.
10. Install the upper bae and refractory liner panels. See page diagrams on page 14 and 16.
11. Install the heat outlet louver, if used, which is magnetically held in place.
12. Notice to installers: Save these instructions for future use. These instructions include operation
instructions, maintenance information and the customer’s warranty. Leave this booklet inside of the unit for
the consumer.
Care and Maintenance
Creosote Formation and the Need for Removal
When wood is burnt, it produces organic vapors and tar which combine with moisture that is expelled from the wood
and forms a black deposit called creosote. The creosote forming vapors condense in the relatively cool ue liner of a
slow burning re. As a result, creosote residue accumulates on the ue lining. When ignited, creosote burns extremely
hot. Excessive accumulation of creosote, if ignited, can cause over heating of the chimney, chase and replace structure.
Overheating is a re hazard. Creosote accumulation can be minimized by burning hot res using only well-seasoned, air
dried fuel. Any wood that sizzles in the re will produce excessive creosote formation in the ue and should not be used.

18
Regular chimney maintenance combined with the proper burning techniques will prevent chimney res. Keep the chimney
area, cap and ue lining free of build-up. Do not allow more than 1/8 inch to accumulate between cleanings to avoid a
chimney re. Cleaning intervals will depend on individual use practices and your fuel. Do not use wood with more than 20%
moisture content. Moisture meters are available through your dealer.
We recommend monthly inspection of the chimney system and cleaning if needed. At a minimum the chimney should be
inspected at least twice during the heating season to determine if a buildup has occurred. This will allow you to learn how
your burning style aects the formation of creosote in the ue. Have your chimney professionally cleaned. If you choose
to maintain it yourself, remove the cap on top of the chimney and use a sti plastic/poly brush. Metal brushes will damage
the stainless steel chimney due to scratching of the inner surfaces. Prior to cleaning the chimney, remove the steel and
refractory baes located in the throat of the replace and the angled refractory above the re chamber so any creosote
that falls into the system during cleaning falls down to the base of the replace. Remove the creosote from the rebox prior
to starting the next re. Creosote left inside the replace will burn at an extremely high temperature and may damage the
replace or chimney system.
If You Have a Chimney Fire
If a chimney re occurs, close the combustion air control by pushing it into the locked position. Verify that the doors are
fully closed, summon the re department, alert your family of the possible danger and evacuate the premises. A chimney
re is a serious condition that may result in loss of property and life.
Do not use the replace if you suspect that you have had a chimney re until the entire system has been inspected by a
certied sweep or others qualied in the area of chimney/replace safety.
Ashes
Removal of ashes should be done when the re is out and the ash is cold. A special ash bucket is available from your dealer
to ease the ash removal process. Always empty ash into a metal container with a lid. Close the lid tight and set it on a non-
combustible surface well away from any combustible material. Do not store ash in your home. Never use a cardboard box
for ash removal.
Disposal of ashes: The closed container of ashes should be placed on a noncombustible surface or the ground, well away
from combustible materials, pending nal disposal. If ashes are disposed of by burial in soil or otherwise locally dispersed,
they should be retained in the closed container until all cinders have thoroughly cooled. Hot coal in the ash can remain
potentially dangerous several days after removal.
Care of the Glass Panels
The glass used in this replace is a 1400 degree ceramic glass. If for some reason it ever breaks, replace it with a similar
material as a regular glass or tempered glass cannot withstand the intense temperature that the re creates. Contact your
dealer or Wilkening Fireplace Co. for proper replacement parts. To replace the glass remove the screws from the outside
perimeter of the glass frame, lift the U channels with gasket out and clean any fragments before reinstalling the new glass.

19
To clean the glass, use an ammonia based cleaner, locally available replace glass cleaners or Speedy White. Contact your
dealer or Wilkening Fireplace Co. to obtain Speedy White glass cleaner. Take care not to apply the cleaner in a manner that
it contacts painted areas or electroplated surfaces as discoloration may occur. Cleaner combined with the creosote will
cause the gaskets to harden.
Use a soft cotton cloth or paper towel to remove the smoke/cleaner residue. Do not scrape the glass with razor blades
or abrasive pads. This will damage the glass and may cause failure. Clean the glass only when the unit has cooled to room
temperature.
Heat Output
The GranView replace generates the greatest BTU output when smaller, split fuel is used. The unit is operating at peak
performance when the ames burn clean and clear.
This is a single burn rate appliance. Never close the combustion air supply when the re is burning. The re requires air for
combustion and closing the air supply will exhaust the re and create a buildup of gasses in the combustion chamber.
Front Clearance
Keep any combustible materials at least 3 feet away from the front of this replace. This includes furniture.
Refueling
When adding fuel to the re it is important to crack open the doors for 15 seconds to clear any smoke. For optimum
performance always maintain a hot rebox temperature. This is achieved by maintaining a hot coal bed and not stacking or
overloading the unit with fuel. Failure to do so can create a smoldering, smoky re. Maintaining a hot rebox will minimize
smoke on the glass and creosote in the chimney.
Doors
WARNING: Fireplaces equipped with doors must be operated with BOTH doors fully open or fully closed. If
the doors are partially open, gas and ame may be drawn out of the replace opening, creating risks of both
re and smoke damage. Doors may be cracked open on a cold start up or when refueling for up to 15 minutes.
Door Options Available: Black Rectangular Tudor (part #GVBRT), Black Rectangular Prairie Style Tudor (part #GVBRTP),
Black Arched Tudor (part #GVBAT), Nickel Rectangular Tudor (part #GVNRT), Nickel Arched Tudor (part #GVNAT) and
Single Black Rectangular (part #GVBRS).

20
Back Smoking
To minimize smoke from entering the room when refueling, crack both doors open slowly at the same time and refuel.
Excessive amounts of fuel or wet fuel will also create the potential for back smoking when the door is open due to over
capacity of burning fuel or low draft due to low rebox temperature.
Chimney blockage due to foreign objects (leaves, nest, etc.) or excessive creosote in the ue will minimize draft of the
chimney and can be a cause of poor draw.
Lack of chimney height will also contribute to poor draw. The chimney must extend at least 2’ taller than any roof or
structure that is within 10’ of it. When this unit is installed with osets, it may also be necessary to compensate for the
decrease in draw with additional chimney height.
Open both doors at the same time, slowly. This will minimize the vortex action created by the air owing into the replace
and will reduce the possibility of back smoking once the doors have been opened fully.
If the replace has been operating properly and all of a sudden starts to smoke, check that the chimney cap has not become
plugged or that loose creosote has not fallen down the chimney and is obstructing the holes in the upper most bae.
Annual Inspections
Every replace should have an annual inspection before the rst re of the year to verify that all components are working
properly and that the chimney is ready for use. We recommend contacting a Certied Chimney Sweep or your dealer for
this yearly inspection even if you clean your own chimney during the year. This will assure you that there has not been any
breakdown in components or blockages that could result in a re. As trained professionals, they can fully assess your system.
Starting the First Fire
The First Fire
The rst two res should be small, short in duration (less than one hour) and not contain rapidly combustible material such
as building scrap or siding. The rst re should be especially short as this will remove most of the moisture in the refractory
liner and heat cure the gasket cement. The rst several times of use will produce a slight odor or smoke as the painted
surfaces are curing.
For this reason the room should be well ventilated during the initial res. During the curing process, the glass may develop
creosote stains as the re is not hot enough for it to “self-clean”.
Starting the Fire
To start a re, open the combustion air supply by lifting up slightly on the spring handle on the lower left of the replace
front. An internal spring will open the supply. Place 8-10 sheets of newspaper crumpled into balls in the center of the
rebox. Lay two, small diameter, split logs on each side of the paper with the cut end facing you. Build the re directly on