Winstec Millennium FX User manual

Millennium FX
Car Monitoring System
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Caution : Any changes of modifications in construction of this device which are not
expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
1- 9
CAR MONITOR
(Model RCM-3000)
User Guide and Installation Manual
Car Monitor (Millennium FX) is your complete solution to provide you with
live monitoring and surveillance for your vehicle. No more guessing what
happens to your car while shopping, working, or staying at home.

1- Asmall and innovative hand pager(that can be carried in the supplied belt
clip, or in your pocket or handbag), will instantly alert you should your parked
vehicle be violated. The alert is selectable, from either a musical melody, or a
silent vibration. While no sound is emitted from the vehicle, a neat LCD
display on the pager accurately monitors doors open/closed status, hood and
trunk open/closed status, and hard impacts to your vehicle.
It even advises whether the vehicle’s engine has been started.
2- The high tech display is back lit, and also indicates other useful information
such as whether or not you are within the effective range of the system, the
current time, a reminder alarm, alert mode selection, low battery, and more.
3- Car Monitor(Millennium FX) uses FM and other new technologies making it
suitable for any make and model of 12-volt vehicle with or without an existing
car security alarm, and provides the highest performance, most reliable quality
and longest service distance (This range depends upon local Radio Frequency
laws).
Car Monitor(Millennium FX) is ideal for vehicles fitted with factory
immobilisers, effectively increasing the level of security.
2 - 9
MONITORINGYOUR VEHICLE
Trigger Zones
Your pager will immediately alert you of a violation to your vehicle.
A melody or vibration will be emitted, and a visual icon will display on the LCD
Screen.
1) Door Open / Closed Status
2) Engine Start Status
3) Impact Status(Pre-warn Zone and full trigger, depending upon the exiting
security system)
4) Hood Open / Closed Status
5) Trunk Open / Closed Status
Operation
1) The transmitter of Car Monitor will be automatically turned off 30 seconds
after the vehicle’s engine is started.
2) When Car Monitor is installed with an existing security alarm, Car Monitor is
designed to be controlled, and automatically turned ON or OFF by the
operation of the existing remote control system.
As soon as the vehicle is armed, Car Monitor is turned ON.

3 - 9
ENHANCED USER FEATURES
1) Out-of Range Indicator ( 1 ). The symbol ( 1 ) indicates that Car Monitor is
within the operational range.
Out of Range Alert Selection : Silent or Tone alert.
Press Button (■
■■
■) repeatedly until the symbol(1) starts flashing.
Select ON or OFF by pressing Button ( ). Press Button (■
■■
■) to confirm.
When ON is set, Car Monitor will emit “beep” immediately in Out-of Range
Area. When OFF is selected, no sound will emit even in Out- of Range Area.
2) Low Battery Indicator ( 3 ). The symbol( 3 ) flashes and emits a beep when the
Internal battery reaches the low level. We recommend the battery(AAA) is
replaced immediately.
3) Resetting the Car Monitor ( 4 ). Press Button (■
■■
■) once, and the symbol (Off)
will be flashing. Press button ( ) to confirm the OFF mode. Car picture will
disappear. Wake-Up alarm and Current Time still remain functional.
4)Setting Vibrating Alert Mode ( 5 ). Press Button (C
CC
C) repeatedly until the symbol
( 5 ) starts flashing. Press Button ( ) to confirm Vibrating Alert Mode.
5)Setting Melody Alert Mode ( 6 ). Press Button (C
CC
C) repeatedly until the symbol
( 6 ) starts flashing. Press Button ( ) to confirm Melody Alert Mode.
6) Setting Current Time mode ( 7 ). Press Button (C
CC
C) repeatedly until the symbol
( 7 ) starts flashing. Press Button ( ) to select Time Setting Mode.
Change the Hour, Minute and AM / PM by pressing Button ( ).

To confirm each press Button (C
CC
C).
7) Setting Wake-Up Call Mode ( 8 ). Press Button (C
CC
C) repeatedly until the symbol
( 8 ) starts flashing. Press Button ( ) to select Wake-Up Mode.
Change On / Off by pressing Button ( ). To confirm press Button (C
CC
C).
Do the same procedure to enter the time data as Current Time Mode.
4 - 9 Specifications
Transmitter Monitor
RF Output Power
Modulation
Current Consumption
Standby Mode
Active Mode
Power Source
Dimension
Auto On / Off
1mW
FM
13mA
33mA
DC 12V
91x70x30mm
Off
30seconds
after Engine
is started.
Starter Kill
(Negative
Armed)
The number of code
Sensitivity
Current Consumption
Standby Mode
Active Mode
Power Source
Dimension
Weight W. / Battery
Auto On / Off
65,550
107dBM
1mA
5mA
1.5V
1AAAAlkaline
63x44x18.9mm
60g
Same as left
5 - 9

CODE LEARNING
Step 1 : Installing the Control Module
Connect all the wire harnesses, and power the module as per the installation
guide. Make sure to close the door, the trunk and the hood of the vehicle.
Do not start the engine. You have 30 seconds to complete Step 2.
Step 2 : Setting Code Learning Mode for the LCD receiver
a) Press and hold Button ( ) more than 1 second or until you hear a short beep
tone.
b)Press Button ( ) 4 times. The current time will change to (0:00), indicating
the LCD receiver is on code learning mode and is communicating with the
main control module.
Step 3 : Receiving ID Data.
When ID data is successfully delivered to the LCD receiver, (0:00) changes to
current time and LCD screen will be back to Standby Mode by emitting a song
titled as Congratulation.
The Out-of –Range icon will re-appear at the left top corner of the screen to
confirm that the operation is terminated.
Step 4 : Testing Car Monitor.
Arm the host alarm and Open / Close the door, the hood, the trunk or start the
vehicle.
Tempered location must be displayed on LCD screen as it occurs.
Otherwise re-do steps 1 to 4.
6 - 9
BLOCK DIAGRAM FOR CODE LEARNING
Install Car Monitor TX

Close Doors, Trunk, Hood and Turn Off
Engine
Within 25 seconds
Step#1 : Press button( ) longer than 1 second.
Step#2 : Press ( )again 4 times shortly
Time Display changed to [0:00]
Prepare RX mode to receive ID data
30 seconds
Code Learning Success
Congratulation Song emits
Check and Re-confirm
Open Door / Trunk/ Hood and Start engine(while armed)
7 - 9

8 - 9

9 - 9