Wonders Technology HX-P200 Instruction Manual
HX-P200
Instruction Manual and
Warranty Information
1
HX-P200: The ultimate
wireless speaker!
Thank you for purchasing the
HX-P200 wireless speaker for
smartphones, tablets,
notebook computers and other
Bluetooth enabled devices.
Approximately 2 hours required for full
charge. Can be charged by using the
USB to Micro USB cord (included)
through computer or AC adapter with
USB jack (not included).
Note: Battery will last up to
4 hours when connected
wirelessly and up to 12 hours when
connected through
Aux-In Audio Jack.
Package Contents
User Manual
Charging Cord
Speaker
Charging the Unit
Controls
Indicators
Power Switch
Play/Pause Button
Volume Controls
Bluetooth Indicator
Line-In Audio Jack
Charging Port
Battery Status Indicator
CHARGE
Solid RED
Power ON
Charging
Fully Charged
OFF
Quick Flash BLUE Pairing Mode
Slow Flash BLUE Paired
Solid RED Line-in Mode
Indicator Status
2
3
4
5
6
7
1
2
3
4
5
6
7
CHARGE
(when
charging)
To listen to your music over Bluetooth wireless connection, you need to pair your
device with HX-P200:
1. Make sure your device has Bluetooth capability.
2. Slide POWER SWITCH to turn on the unit, indicator will begin to ash.
3. Follow the instructions of your device to pair the unit.
4. Pair your device with the unit by selecting HX-P200 from your Bluetooth listings
on your device or selecting YES. If prompted, then you will listen the paired
successful prompt sound.
5. Press play on your device and use controls on the unit to adjust desired volume.
NOTE: Once you have successfully paired your device, you typically will not need
to repeat the above steps. Please ensure the unit source is set to Bluetooth and
your device has Bluetooth enabled.
NOTE: When pairing with a computer running windows 7 OS, please consult your
computer manufacturer for Bluetooth pairing instructions and/or Bluetooth
Drivers.
Listening to your device wirelessly over Bluetooth®
8
8
CHARGE
BLUETOOTH
BLUETOOTH
Forware/Reverse
TM
FCC Disclaimer:
One Year Limited Warranty:
Note: This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modications to this equipment. Such modications could void
the user authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For detailed Warranty Instructions and Information visit :
www.homedics.com/audio-and-electronics/portable-audio/jam.html
To obtain warranty service on your HMDX product, contact a Consumer
Relations Representative by telephone at 1-800-466-3342 or email
number of the product available. Representatives are available 8:30am - 7:00pm
EST Monday-Friday.
HX-P200 and HMDX Audio® are trademarks of HoMedics.
©2012 HoMedics, Inc. All Rights Reserved.
IB-HXP200
1. Connect Aux-in cable to the headphone or line-out jack of an audio device
and plug the other end of the cable into the Line-In Audio Jack on the back
of the unit.
2. Slide the POWER SWITCH to turn on the unit.
3. Press PLAY on the device and use controls on the unit to adjust
desired volume.
Listening to your device through
the Auxiliary Line-In Audio Jack
Table of contents
Other Wonders Technology Speakers manuals
