Worcester DT10RF User manual

SET? SELECT
YES
Digistat Optimiser
SET? SELECT
YES
Digistat
DIGISTAT - Radio frequency controlled programmable room thermostat
with domestic hot water programmer
FOR GREENSTAR i and GREENSTAR Si MODELS
OPTIMISING DIGISTAT - Radio frequency controlled programmable
optimising room thermostat with domestic hot water programmer
FOR GREENSTAR Si MODELS
INSTRUCTION MANUAL
FITTING & OPERATING INSTRUCTIONS
DT10RF PROGRAMMER
DT10RF OPTIMISING PROGRAMMER
set?
OK
off
time
once
on
select a vance
MON TUE WED THU FRI SAT SUN
CLOCK? PROG? DATE? HDAY?
AM OFF
CHW ON
SET? SELECT
YES
Digistat Optimiser
SET? SELECT
YES
Digistat
FOR GREENSTAR Si MODELS
off
time
once
on
MON TUE WED THU FRI SAT SUN
CLOCK? PROG? DATE? HDAY?
AM OFF
CHW ON
SET? SELECT
YES
SET? SELECT
YES
Digistat
set?
OK
off
time
once
on
select a vance
MON TUE WED THU FRI SAT SUN
CLOCK? PROG? DATE? HDAY?
AM OFF
CHW ON

CONTACT & MANUAL
INFORMATION
FITTING & OPERATING INSTRUCTIONS FOR WORCESTER BOSCH
DT10RF PROGRAMMER & DT10RF OPTIMISING PROGRAMMER
-716-106-652 issue c (01.05) UK
PLEASE READ THESE INSTRUCTIONS
CAREFULL BEFORE STARTING
THESE INSTRUCTIONS ARE APPLICABLE TO THE
WORCESTER BOSCH MODEL(S) STATED ON THE
FRONT COVER OF THIS MANUAL ONLY AND MUST NOT
BE USED WITH ANY OTHER MAKE OR MODEL
THE INSTRUCTIONS APPLY IN THE UK ONLY AND
SHOULD BE FOLLOWED EXCEPT FOR ANY STATUTORY
OBLIGATION
IF YOU ARE IN ANY DOUBT CONTACT WORCESTER
BOSCH TECHNICAL HELPLINE
THIS ACCESSORY MUST BE FITTED BY A COMPETENT
PERSON. FAILURE TO COMPLY COULD LEAD TO
PROSECUTION.
LEAVE THESE INSTRUCTIONS WITH THE USER OR AT
THE APPLIANCE.
CONTACT INFORMATION
WORCESTER BOSCH:
TECHNICAL: 0 705 266241
SERVICE: 0 547 256206
SPARES: 01905 752571
LITERATURE: 01905 752556
TRAINING: 01905 752526
SALES: 01905 752640
WEBSITE: www.worcester-bosch.co.uk
MANUAL INFORMATION
ABBREVIATIONS:
CH Central Heating
HW Domestic Hot
Water
RF Radio Frequency
DLS Day Light Saving
BST British Summer
Time
GMT Greenwich Mean
Time
CCelcius
mMetre
IP Ingress
Protection
VVolts
mA MilliAmps
DEFINITIONS (DLS/BST):
Summer perio begin: Last Sunday in March at 1:00
AM GMT (Clock put forward by 60 minutes)
Summer perio en : Last Sunday in October at 2:00
AM GMT (Clock put back by 60 minutes)
S MBOLS:
Central Heating
Domestic Hot Water
Radio Frequency (RF) transmitter

SERVICING
& SPARES
USER
INSTRUCTIONS
INSTALLATION &
COMMISSIONING
ACCESSORY
INFORMATION CONTENTS
1
CONTENTS
FITTING & OPERATING INSTRUCTIONS FOR WORCESTER BOSCH
DT10RF PROGRAMMER & DT10RF OPTIMISING PROGRAMMER
-716-106-652 issue c (01.05) UK
ACCESSORY INFORMATION
GENERAL INFORMATION 2
TECHNICAL DATA 3
INSTALLATION & COMMISSIONING:
FITTING THE RECEIVER 4
SETTING UP THE RADIO LINK 5
TRANSMITTER LOCATION, CLEARANCE & FIXING 6
USER INSTRUCTIONS:
TRANSMITTER OPERATING CONTROLS 7
TRANSMITTER PRE-SET PROGRAMS
TRANSMITTER SETTINGS
Setting the clock 9
Setting times and temperatures 10, 11
RECEIVER OPERATING CONTROLS 12
RECEIVER PRE-SET PROGRAMS 13
RECEIVER SETTING PROGRAMS
Setting MON - FRI 14
Setting individual weekdays 15
Setting SAT & SUN 16
Setting individual weekend days 17
RECEIVER SETTING HOLIDAYS 1
RECEIVER SETTING THE CLOCK 19
RECEIVER SETTING THE DATE 20
BATTERY REPLACEMENT 21
SERVICING & SPARES:
MAINTENANCE & SPARES 22
CONTENTS

SET? SELECT
YES
ACCESSORY
INFORMATION
2GENERAL INFORMATION FITTING & OPERATING INSTRUCTIONS FOR WORCESTER BOSCH
DT10RF PROGRAMMER & DT10RF OPTIMISING PROGRAMMER
-716-106-652 issue c (01.05) UK
STANDARD PACKAGE:
A - DT10 Programmer/ RF receiver
B - Remote RF transmitter
C - Screws (x2)
D - Wall Plugs (x2)
E - Instructions
F - Batteries (x4)
SPECIFICATIONS:
Receiver:
Programmer/receiver for DHW
mounted into the boiler fascia
7 day programmer
3 on/off periods per day
Automatic BST settings
Pre-programmed on/off periods
Dedicated advance buttons
12 or 24 hour back-lit digital display
Holiday function
Pre-wired with PCB connector
Digistat transmitter:
Radio frequency controlled
programmable room thermostat with
domestic hot water programmer
Remote 24 hour programmable RF
Transmitter to control CH
temperature
AA alkaline LR6 batteries included
Low battery warning
Max. signal range approx. 25 metres
(range may decrease according to
the building construction).
Digistat Optimising transmitter:
Radio frequency controlled
programmable optimising room
thermostat with domestic hot water
programmer
Same as Digistat above, plus:
Remote 7 day programmable RF
Transmitter to control CH
temperature
Optimum start.
GENERAL INFORMATION
set?
OK
off
time
once
on
select a vance
MON TUE WED THU FRI SAT SUN
CLOCK? PROG? DATE? HDAY?
AM OFF
CHW ON
A
B
E
C
D
F

ACCESSORY
NFORMATION
3
TECHNICAL DATA
FITTING & OPERATING INSTRUCTIONS FOR WORCESTER BOSCH
DT10RF PROGRAMMER & DT10RF OPTIMISING PROGRAMMER
-716-106-652 issue c (01.05) UK
DESCRIPTION UNITS DT10RF Receiver
TECHNICAL DATA
Dimensions mm -
Electrical supply - 24v DC <65mA
Ambient operating temperature C 0 to +50
Humidity operating range % non-condensing up to 45° 30 - 95
Class of protection - II
Degree of protection IP 24
Accuracy @25°C sec/day <±1
Battery life years 10
Battery backup time & date years min. 10
Shortest switching period minutes 1
On/Off periods number 3
Programs days 7
Relate Stan ar s:
BS EN60730-1:2001
BS EN60730-2-7:1992
Electro Magnetic Compatibility and Radio Spectrum Matters (ERM); Short Range Devices (SRD) ETSI
EN 300 220-1
EC Directives:
European Union Law Directive 2000/ 4/EC
Low Voltage Directive (73/23/EEC)
Electro Magnetic Compatibility Directive ( 9/336/EEC)
CE Marking Directive (93/6 /EEC)

INSTALLATION &
COMMISSIONING
4FITTING THE RECEIVER FITTING & OPERATING INSTRUCTIONS FOR WORCESTER BOSCH
DT10RF PROGRAMMER & DT10RF OPTIMISING PROGRAMMER
-716-106-652 issue c (01.05) UK
FITTING THE RECEIVER
DANGER - 24V &
230V: DO NOT TOUCH
THE ELECTRICAL
COMPONENTS OR
CIRCUITS.
CAUTION: ISOLATE THE MAINS
ELECTRICITY SUPPLY BEFORE
STARTING ANY WORK AND
OBSERVE ALL RELEVANT
SAFETY PRECAUTIONS.
Important: Switch off boiler
Remove boiler outer casing and
control panel fascia to gain access
to the heatronic control panel
1Release securing screw (A)
2Pull cover panel (B) upwards to
remove
3Grip tab (C), pull upwards to
disengage clips (D) and pull
forwards to remove blanking plate
(E) or existing programmer
4Align connector pins (F) into
receptors (G) in the pcb and push
fully home
5Feed the ribbon cable (G) into
recess (H)
6Align programmer (E) and locate
clips (D), push into slots then
downwards to secure using grip
tab (C)
7Locate cover panel (B) and secure
with screw (A)
Replace fascia cover and outer
casing before switching on the
electricity supply and boiler
Switch boiler on when completed.
Refer to USERS INSTRUCTIONS
section for details of pre-set and
setting programs.
OBSERVE ELECTRONIC STATIC
DISCHARGE PRECAUTIONS.
DO NOT TOUCH THE PCB
CIRCUITS
1
AB
D
E
C
2
3
F
E
4
AB
D
7
H
G
6
E
C
5

6
AA AA
AA AA
C
B
SET? SELECT
YES
D
A
INSTALLATION &
COMMISSIONING
5
SETTING UP THE RADIO
LINK
FITTING & OPERATING INSTRUCTIONS FOR WORCESTER BOSCH
DT10RF PROGRAMMER & DT10RF OPTIMISING PROGRAMMER
-716-106-652 issue c (01.05) UK
SETTING UP THE RADIO
LINK
Receiver set up:
The colon, CH and antenna symbols
should flash on the display
1Press the 'set?' button 4 times
2Press the 'OK' button once
3Press the 'set?' button 4 times; 'Lrn'
and 'OFF' should be displayed
4Press the '+' button so the display
shows 'ON' and a flashing antenna
symbol. The learn mode is now ready
to receive a signal from the transmitter
during the next 2 minutes.
Transmitter set up:
he transmitter must be at least 1 metre
away from the receiver before starting
this procedure:
5Slide open battery compartments (B)
6Remove insulator strips (C)
7Replace the right han battery
compartment (B) first followed by
the left hand battery compartment
he display (D) then shows the room
temperature and automatically transmits
a signal to the receiver unit in the boiler
to establish a radio link.
8When a radio link has been
established the display reverts back
to normal operation with the antenna
symbol shown
To re-establish the radio link; open both
battery trays until the transmitter display
goes blank, repeat steps 1 to 4 then
step 7 to transmit a set up signal to the
receiver. Repeat this procedure until a
link has been established.
If the radio link is lost the antenna,
colon and CH symbols flash on the
receiver display. he program defaults
to manual mode. Press the 'OK' button
to override and switch the heating ON,
press again to switch OFF.
57
8
4
2
x4 x1
1
3
x4

INSTALLATION &
COMMISSIONING
6TRANSMITTER LOCATION
CLEARANCES & FIXING
FITTING & OPERATING INSTRUCTIONS FOR WORCESTER BOSCH
DT10RF PROGRAMMER & DT10RF OPTIMISING PROGRAMMER
-716-106-652 issue c (01.05) UK
TRANSMITTER LOCATION
CLEARANCES & FIXING
CAUTION: Ensure there are no
pipes, electric cables or other
hazar s before rilling.
SAFETY: All relevant safety
precautions must be undertaken.
Protective clothing, footwear, gloves
and safety goggles must be worn
as appropriate.
Transmitter location:
1Position the transmitter (A) as close
to the main living area as possible
onto a flat inside wall, approx. 1.5m
(5') above the floor within max. signal
range of the appliance receiver.
Keep the transmitter away from:
light and heat sources
enclosures and curtains
direct draughts, including fans, air
vents, windows and doors
damp and condensation
Replacing a mains wired unit:
Isolate the main electric supply. Refer
to the manufacturers instructions to
remove the unit. Isolate the existing
wiring and make electrically safe.
Transmitter clearances:
See diagram opposite for minimum area
required for operation.
Transmitter fixing:
2Loosen screw (C) on transmitter to
remove the baseplate (B)
3Hold baseplate (B) level to mark
securing points (D) and remove
baseplate (B)
4 Drill holes to marks
Fit one wall plug into each hole
Reposition baseplate (B), check
level and secure with screws supplied
Refit the transmitter to the baseplate
(B) and tighten screw (C) to secure.
123
1.5m (5)
SET? SELECT
YES
Digistat Optimiser
3
1
DD
50mm
70mm C
2
B
A

SET? SELECT
YES
SET? SELECT
YES
SET? SELECT
YES
7
TRANSMITTER
OPERATING CONTROLS
FITTING & OPERATING INSTRUCTIONS FOR WORCESTER BOSCH
DT10RF PROGRAMMER & DT10RF OPTIMISING PROGRAMMER
-716-106-652 issue c (01.05) UK
USER
INSTRUCTIONS
TRANSMITTER
OPERATING CONTROLS
To select a pre-set CH program:
1Press the 'SELECT' button to
change to the program to suit your
requirements as follows:
Normal running (all pre-set times and
temperatures)
Continuous '1' first temperature
Continuous 'night' temperature
The flame symbol indicates:
Flame on = heating demand ON
Flame off = heating demand OFF
Flame flashing = energy saving for
Optimiser only
To change the room temperature:
Note: the following only occurs during
a timed on period and has no effect
when the receiver is in an off setting.
2To increase the room temperature:
press the '+' button until the required
temperature is displayed
3To decrease the room temperature:
press the '-' button until the flame
symbol is no longer displayed
After 5 seconds the display reverts
back to the actual room temperature.
Optimium start (Digistat Optimiser
only):
This unit features an energy saving
system which, during milder weather,
automatically delays the first start up
of the day from 0 to 60 minutes
depending on:
 actual room temperature at the first
switch on time only
 set temperature at the first switch on
 how fast the heating system
responded on the previous day
Press the '+' button once only to
override a delayed start.
1
1
2
3

SET? SELECT
YES
USER
INSTRUCTIONS
8TRANSMITTER
PRE-SET PROGRAMS
FITTING & OPERATING INSTRUCTIONS FOR WORCESTER BOSCH
DT10RF PROGRAMMER & DT10RF OPTIMISING PROGRAMMER
-716-106-652 issue c (01.05) UK
TRANSMITTER
PRE-SET PROGRAMS
Transmitter:
The default pre-set daily start times
and temperatures are shown in the
table opposite for the Digistat (24 hour)
and the Digistat Optimiser (7 day)
remote transmitters
Press the 'select' and '-' buttons
together and hold for 2 seconds to
reset the default program times
See ' RANSMI ER SE ING
PROGRAMS' in the USER
INS RUC IONS section if changes
are required to the clock time or pre-
programmed settings.
123
Central Heating:
MON to FRI:
Start time 6:30 :30 16:30 22:30
Temperature °C 20 16 21 7
SA & SUN:
Start time 7:00 9:00 16:00 23:00
Temperature °C 20 16 21 7
123
Central Heating:
24 Hours:
Start time 6:30 :30 16:30 22:30
Temperature °C 20 16 21 7
DIGISTAT OPTIMISER
(7 DA ) PRE-SET PROGRAM
DIG ISTAT
(24 HOUR) PRE-SET PROGRAM