Workrite Ergonomics Sequoia SQ-312 User manual

Workrite Sequoia
Assembly Instructions for
Model SQ-312
#1500204 - Rev A

AA Capped Pole Qty: 1
BCable Manager Qty: 1
KOutside VESA Mount Qty: 2
CCollar Qty: 1
FVESA Mount Knob Qty: 2
EPlastic Washer Qty: 2
DRatchet Lever Qty: 2
LWing Bar Qty: 2
Capped Pole carton, 2 monitors, includes base:
Hardware Packs:
GM5 × 4mm Set Screw for Collar
Qty: 3
HM4 × 8mm VESA Mount Screws
Qty: 8
I2.5mm Hex Wrench Qty: 1
Need Bolt!
OR
Hardware Packs:Desk Mounts:
T2 Piece C-Clamp Mount
Qty: 1
UGrommet Mount Qty: 1
GM5 × 4mm Set Screw for Desk Mount
Qty: 3 VM6 × 10mm Alan Cap Bolt
Qty: 2
WM8 × 65mm Grommet Bolt Qty: 1
I2.5mm Hex Wrench Qty: 1 S6mm Hex Wrench
Qty: 1
S6mm Hex Wrench Qty: 1
XGrommet Clamp Plate Qty: 1
GM5 × 4mm Set Screw for Desk Mount
Qty: 3
I2.5mm Hex Wrench Qty: 1
Parts grouped by carton
Note: Part letters are nonsequential to accommodate all Sequoia Models

BB Pole Coupler Qty: 1
BCable Manager Qty: 1
JCenter VESA Mount Qty: 1
CCollar Qty: 1
DRatchet Lever Qty: 1
Extension Pole carton, 1 monitor:
Hardware Packs:
GM5 × 4mm Set Screw for Collar
Qty: 3
HM4 × 8mm VESA Mount Screws
Qty: 4
I2.5 mm Hex Wrench Qty: 1
Verify that you have all the hardware and tools needed for the assembly.
Check your packages against the parts list above to verify that you have all the parts needed. You will
also need the following tools:
#3 tip Phillips screwdriver
AExtension Pole Qty: 1

Assemble Desk Mount
1
Install the Extension Pole (A) into
the threads in the mount and tighten
securely.
Insert 2 Set Screws (G) into the rear
of the base and tighten securely with
the 2.5mm Hex Wrench (I)
2
b
b
a
a
Attach Extension Pole, Cable Manager & Collar
C-Clamp Mount:
Note: If you have easy access you can assemble the clamp
before placing it onto the work surface and tightening it
down.
Place the Clamp Base (T) over the rear edge of the
workstation. Attach the Clamp Bracket to the Clamp Base
with 4 M6 × 10mm Alan Cap Bolts (V) and tighten with
6mm Hex Wrench (S)
Grommet Mount:
Note: A grommet hole or small drilled hole from 3/8”
diameter to a grommet hole up to 2.5” diameter is required
to mount the grommet mount.
Place the Grommet Mount Base (U) over the grommet hole
or drilled hole in the worksurface. From the bottom place
the bolt (X) through the Grommet Clamp Plate (W) and
tighten securely with the 6mm Hex Wrench (S)
Install Cable Manager (B) onto the
Pole and slide down to the bottom.
Place Collar (C) onto the pole about
6” up from the bottom and install Set
Screw (G) and tighten securely.
VS
S
U
WX
T
G
G
A
B
I
CG

Attach Monitor Mounts to Monitors
3
b
a
Important Note
It is strongly recommended to use the mounting screws
provided by the monitor manufacturer if possible. Always use
the shortest screws possible to avoid damage to the monitor.
!
Center Monitor Mount:
Align the Center Monitor Mount (J) to the VESA
pattern in the monitor. Install 4 VESA Monitor
Screws (H) and tighten securely with a #2 Phillips
screwdriver.
Outer Monitor Mount:
Align the outer mounts (K) to the VESA pattern
in the monitors. Install 4 VESA Monitor Screws
(H) and tighten securely with a #2 Phillips
screwdriver.
Note: At this time you can chose to install the
monitors in landscape or portrait orientation.
Before mounting be sure to measure the vertical
height required for Portrait mounting as some
monitors may exceed the vertical height limit for
installation.
J
H
H
K

Attach Wing Bars to Pole
Attach Monitors to Wing Bars
4
5
Place Left rst then Right Wing Bars (L) onto Pole and
rest on Collar (C). Dual Wing Bars are identical and
interchangeable.
Install Ratchet Lever (D) into the rear of the Wing Bar
and tighten.
a
b
a
b
Note: During installation it may be necessary to adjust
overall height of the assembly. To do this simply
loosen the Allen set screw (G) in the Collar( C) with
the 2.5mm Hex Wrench (I) and move accordingly.
Retighten the Allen Screw and Wing Bar Mount when
desired height is reached.
Align the Outside VESA Mount (K) with the slot in the
Wing Bar. Place Plastic Washer (E ) onto the Mount
Knob (F). Install the Knob and Washer into the Mount
as shown and tighten securely.
Repeat for the remaining outer monitor.
Note: During assembly it may become necessary
to adjust the width of the outer monitors to adjust
for curved alignment and minimize gaps between
monitors. To do this simply loosen, move, and retighten
the Mount Knob (F) to the wing bars.
c
D
D
C
L
F
E
K
F
c
a
Left
Right
a
b

Add Capped Pole
6
a
Attach Center Monitor to Capped Pole
7
Place Center VESA Mount (J) on Pole and rest on collar (C).
a
bInstall Ratchet Lever (D) into the rear of the Center VESA
Mount (J) and tighten.
Install the Pole Coupler (BB) into the threads on
the Extension Pole (AA) and tighten securely.
Install the Capped Pole (A) into the threads on
the Pole Coupler and tighten securely.
Insert 2 Set Screws (G) into the Coupler. Tighten
securely with the 2.5mm Hex Wrench (I).
A
AA
BB G
G
C
D
J
J

&
Make Adjustments & Secure Cables
8
Horizontal & vertical adjustments is made by using the VESA Mount
Knob (F) and Ratchet Lever (D). You may need to re-position the
Collar (C) to lower or raise the Wing Bar on the Pole.
Arc adjustment on Dual Arms is made by pulling the Wing Mount
monitors towards you or pushing away from you.
Guide monitor and power cables over and around
Ratchet Levers and Wing Knobs then through the
Cable Manager (B).
Monitor Tilt & Swivel Adjustments
Depending on the size of your monitor, it may be necessary to adjust
the tilt and swivel setting.
If the monitor doesn’t hold its tilt position or is too hard to tilt, adjust
the tension adjustment on top of the Monitor Mount. Use the 2.5mm
Hex Wrench (I), clockwise to increase lift, counter-clockwise to
decrease lift. Check the monitor, and adjust again as necessary.
a
b
c
Swivel
+/- 20°
Tilt
+/- 20°
Dual Horizontal
Adjustment with VESA
Mount Knob
Vertical Adjustment with
Ratchet Lever & Collar
Dual Arc Adjustment
+/- 10°
Important Note
It is recommended to have two people adjusting multiple monitor
congurations after monitors are mounted to the arm assembly.
!
B
B
I
JK
F