Workrite Ergonomics Sequoia SQ-633 User manual

Workrite Sequoia
Assembly Instructions for
Model SQ-633
#1500209 - Rev A

Need Bolt!
BCable Manager Qty: 1 KOutside VESA Mounts
Qty: 2
CCollar Qty: 1
JCenter VESA Mount Qty: 1
FVESA Mount Knob Qty: 2
EPlastic Washer Qty: 2
DRatchet Lever Qty: 3
MRight Wing Bar Mount Qty: 1
NLeft Wing Bar Mount Qty: 1
OWing Bars Qty: 2
Capped Pole carton, 3 monitors, includes Heavy Duty base:
Desk Mount carton:
Hardware Packs:
GM5 × 4mm Set Screw for Collar
Qty: 3
QSteel Spacers Qty: 2
HM4 × 8mm VESA Mount Screws
Qty: 12
R8mm Flat Washer Qty: 4
I2.5mm Hex Wrench Qty: 1
S6mm Hex Wrench Qty: 1
PM8 × 50mm Arm Bolt Qty: 2
OR
Hardware Packs:
TT 2 Piece Heavy Duty C-Clamp
Mount*
Qty: 1
UGrommet Mount Qty: 1
GM5 × 4mm Set Screw for Desk Mount
Qty: 3 VM6 × 10mm Alan Cap Bolt
Qty: 4
WM8 × 65mm Grommet Bolt Qty: 1
I2.5mm Hex Wrench Qty: 1 S6mm Hex Wrench
Qty: 1
S6mm Hex Wrench Qty: 1
XGrommet Clamp Plate Qty: 1
GM5 × 4mm Set Screw for Desk Mount
Qty: 3
I2.5mm Hex Wrench Qty: 1
Parts grouped by carton
Note: Part letters are nonsequential to accommodate all Sequoia Models
AACapped Pole Qty: 1
* Model 633- Requires Heavy Duty Desk Base or Grommet Mount

AExtension Pole Qty: 1
Verify that you have all the hardware and tools needed for the assembly.
Check your packages against the parts list above to verify that you have all the parts needed. You will
also need the following tools:
#3 tip Phillips screwdriver
BCable Manager Qty: 1
KOutside VESA Mounts Qty: 2
CCollar Qty: 1
JCenter VESA Mount Qty: 1
FVESA Mount Knob Qty: 2
EPlastic Washer Qty: 2
DRatchet Lever Qty: 3
MRight Wing Bar Mount Qty: 1
NLeft Wing Bar Mount Qty: 1
OWing Bars Qty: 2
Extension Pole carton, 3 monitors:
Hardware Packs:
GM5 × 4mm Set Screw for Collar
Qty: 3
QSteel Spacers Qty: 2
HM4 × 8mm VESA Mount Screws
Qty: 12
R8mm Flat Washer Qty: 4
I2.5mm Hex Wrench Qty: 1
S6mm Hex Wrench Qty: 1
PM8 × 50mm Arm Bolt Qty: 2
BB Pole Coupler Qty: 1

4 Workrite Ergonomics 800.959.9675 www.workriteergo.com
Workrite Sequoia Monitor Arm - Assembly Instructions
Assemble Desk Mount
1
Install the Extension Pole (A) into
the threads in the mount and tighten
securely.
Insert 2 Set Screws (G) into the rear
of the base and tighten securely with
the 2.5mm Hex Wrench (I)
2
b
b
a
a
Attach Extension Pole, Cable Manager & Collar
Heavy Duty C-Clamp Mount:
Note: If you have easy access you can assemble the
clamp before placing it onto the work surface and
tightening it down.
Place the Clamp Base (TT) over the rear edge of the
workstation. Attach the Clamp Bracket to the Clamp
Base with 4 M6 × 10mm Alan Cap Bolts (V) and
tighten with the 6mm Hex Wrench (S)
Grommet Mount:
Note: A grommet hole or small drilled hole from 3/8”
diameter to a grommet hole up to 2.5” diameter is
required to mount the grommet mount.
Place the Grommet Mount Base (U) over the
grommet hole or drilled hole in the worksurface.
From the bottom place the bolt (X) through the
Grommet Clamp Plate (W) and tighten securely with
the 6mm Hex Wrench (S)
Install Cable Manager (B) onto the
Pole and slide down to the bottom.
Place Collar (C) onto the pole about
6” up from the bottom and install Set
Screw (G) and tighten securely.
S
U
WX
B
I
C
VS
TT
G
G
G
A

Workrite Ergonomics 800.959.9675 www.workriteergo.com 5
Workrite Sequoia Monitor Arm - Assembly Instructions
Attach Monitor Mounts to Monitors
3
b
a
Important Note
It is strongly recommended to use the mounting screws
provided by the monitor manufacturer if possible. Always use
the shortest screws possible to avoid damage to the monitor.
!
Center Monitor Mount:
Align the Center Monitor Mount (J) to the VESA
pattern in the monitor. Install 4 VESA Monitor
Screws (H) and tighten securely with a #2 Phillips
screwdriver.
Outer Monitor Mount:
Align the outer mounts (K) to the VESA pattern in
the monitors. Install 4 VESA Monitor Screws (H) and
tighten securely with a #2 Phillips screwdriver.
Note: At this time you can chose to install the
monitors in landscape or portrait orientation. Before
mounting be sure to measure the vertical height
required for Portrait mounting as some monitors
may exceed the vertical height limit for installation.
J
H
H
K

6 Workrite Ergonomics 800.959.9675 www.workriteergo.com
Workrite Sequoia Monitor Arm - Assembly Instructions
Attach Wing Bar Mounts to Pole
Attach Wing Bars to Wing Bar Mounts
4
5
Place the Right Wing Bar Mount (M) onto the Pole to rest
on the Collar. Place the Left Wing Bar Mount (N) onto the
extension pole to rest on the Right Wing Bar Mount.
Install Ratchet Levers (D) into the rear of both Wing Bar
Mounts and tighten.
a
b
a
b
c
Place 8mm Flat Washers (R) into recesses into the Wing Arm
as shown. Hold in place while attaching Wing Arm to Wing
Arm Mount.
Place Steel Spacer (Q) on M8 × 5mm Arm Bolt (P) and attach
Wing Bars to Wing Bar Mounts. Tighten Securely with 6mm
Hex Wrench (S).
Repeat this step for the remaining Wing Bar.
Hold Flat Washers (R) in
place while attaching.
C
D
D
N
M
R
R
O
MN
&
a
b
S
Q
P
Left
Right

Workrite Ergonomics 800.959.9675 www.workriteergo.com 7
Workrite Sequoia Monitor Arm - Assembly Instructions
Attach Center Monitor to Pole
Attach Outside Monitors to Wing Bars
6
7
a
a
bb
a
b
c
Place Center VESA Mount (J) on Pole and rest
on Wing Mount.
Install Ratchet Lever (D) into the rear of the
Center VESA Mount and tighten.
Note: It’s a combination of the Ratchet Lever,
Wing Mount AND the Collar that holds the
monitor in place.
Note: During installation it may be necessary
to adjust overall height of the assembly. To
do this simply loosen the Set Screw (G) in the
Collar(C) with the 2.5mm Hex Wrench (I) and
move accordingly. Retighten the Set Screw
and Wing Bar Mount when desired height is
reached.
Align the Outside VESA Mount (K) with the
slot in the Wing Bar. Place Plastic Washer (E)
onto the Mount Knob (F). Install the Knob and
Washer into the Mount as shown and tighten
securely.
Repeat for the remaining outer monitor
Note: During assembly it may become
necessary to adjust the width of the outer
monitors to adjust for curved alignment and
minimize gaps between monitors. To do this
simply loosen, move, and retighten the Mount
Knob (F) to the wing bars.
c
a
FE
K
F
J
D

8 Workrite Ergonomics 800.959.9675 www.workriteergo.com
Workrite Sequoia Monitor Arm - Assembly Instructions
Add Capped Pole
8
aInstall the Pole Coupler (BB) into the threads on
the Extension Pole (AA) and tighten securely.
Install the Capped Pole (A) into the threads on
the Pole Coupler and tighten securely.
Insert 2 Set Screws (G) into the Coupler. Tighten
securely with the 2.5mm Hex Wrench (I).
A
AA
BB G
G

Workrite Ergonomics 800.959.9675 www.workriteergo.com 9
Workrite Sequoia Monitor Arm - Assembly Instructions
Attach Wing Bar Mounts to Capped Pole
Attach Wing Bars to Wing Bar Mounts
9
10
Place the Right Wing Bar Mount (M) onto the Capped Pole to
rest on the Collar. Place the Left Wing Bar Mount (N) onto the
Capped Pole to rest on the Right Wing Bar Mount.
Install Ratchet Levers (D) into the rear of both Wing Bar
Mounts and tighten.
a
b
a
b
c
Place 8mm Flat Washers (R) into recesses into the Wing Arm
as shown. Hold in place while attaching Wing Arm to Wing
Arm Mount.
Place Steel Spacer (Q) on M8 × 5mm Arm Bolt (P) and attach
Wing Bars to Wing Bar Mounts. Tighten Securely with 6mm
Hex Wrench (S).
Repeat this step for the remaining Wing Bar.
Hold Flat Washers (R) in
place while attaching.
C
D
D
N
M
R
R
O
MN
&
a
b
S
Q
P

10 Workrite Ergonomics 800.959.9675 www.workriteergo.com
Workrite Sequoia Monitor Arm - Assembly Instructions
Attach Center Monitor to Capped Pole
Attach Outside Monitors to Wing Bars
11
12
a
a
bb
a
b
c
Place Center VESA Mount (J) on Capped Pole
and rest on Wing Mount.
Install Ratchet Lever (D) into the rear of the
Center VESA Mount and tighten.
Note: It’s a combination of the Ratchet Lever,
Wing Mount AND the Collar that holds the
monitor in place.
Note: During installation it may be necessary
to adjust overall height of the assembly. To
do this simply loosen the Set Screw (G) in the
Collar(C) with the 2.5mm Hex Wrench (I) and
move accordingly. Retighten the Set Screw
and Wing Bar Mount when desired height is
reached.
Align the Outside VESA Mount (K) with the
slit in the Wing Bar. Place Plastic Washer (E)
onto the Mount Knob (F). Install the Knob and
Washer into the Mount as shown and tighten
securely.
Repeat for the remaining outer monitor
Note: During assembly it may become
necessary to adjust the width of the outer
monitors to adjust for curved alignment and
minimize gaps between monitors. To do this
simply loosen, move, and retighten the Mount
Knob (F) to the wing bars.
c
a
FE
K
F
J
D

&
Workrite Ergonomics 800.959.9675 www.workriteergo.com 11
Workrite Sequoia Monitor Arm - Assembly Instructions
Make Adjustments & Secure Cables
13
Horizontal adjustments is made by using the VESA Mount Knob (F)
and vertical adjustment is made with Ratchet Lever (D). You may
need to re-position the Collar (C) to lower or raise the Wing Bar on
the Pole.
Arc adjustment is made by pulling the Wing Mount monitors towards
you or pushing away from you.
Guide monitor and power cables over and around
Ratchet Levers and Wing Knobs then through the
Cable Manager (B).
Monitor Tilt & Swivel Adjustments
Depending on the size of your monitor, it may be necessary to adjust
the tilt and swivel setting.
If the monitor doesn’t hold its tilt position or is too hard to tilt, adjust
the tension adjustment on top of the Monitor Mount. Use the 2.5mm
Hex Wrench (I), clockwise to increase lift, counter-clockwise to
decrease lift. Check the monitor, and adjust again as necessary.
a
b
c
Swivel
+/- 20°
Tilt
+/- 20°
Horizontal Adjustment
with VESA Mount Knob
Vertical Adjustment with
Ratchet Lever & Collar
Arc Adjustment
+/- 10°
Important Note
It is recommended to have two people adjusting multiple monitor
congurations after monitors are mounted to the arm assembly.
!
B
B
I
JK