Xanes MD23 User manual

Camera Manual
V24.2
Note: please read the manual carefully before using the product. Thank you.

1.Power button；2.M-Mode button；3.LED；4.TF Card；5.USB；
6.Reset button；7.Magnet
Note：
1). Insert correct memory card (TF Card) before using the device. No memory card is
inserted, the red light will automatically turn off after 5 seconds.
2). No operation after boot, automatic shutdown at 1 minutes.
3).The TF card must be 8GB or above, and the format is FAT32, and the NTFS format
cannot be used normally.Memory below 8GB does not save data properly.
One. Product parameters:
Video format: AVI
Video coding: M-JPEG
Video resolution: 1920*1080
Video frame rate: 30fps
Photo resolution: 4032*3024
Picture format: JPG
Motion detection record: support
Battery capacity: about 180mAh
Record time: about 60 minutes
Charge voltage: DC-5V 1A
Storage support: 8GB-32GB FAT32
Transmission speed: USB 2.0
Interface type: Mini 8PIN USB
Two. Product operation:
The following operation is based on inserting the TF card correctly.
1. Charging:
The built-in rechargeable lithium battery, when the device power shortage, it can be
charged through the following ways:
1). Connect the 5V-1A charger;
2). Connect the mobile power supply(5V-1A);
Note: the red and blue lights are flashing when charging.Once full,the lights are always

on.
2. Power on&Power off
On: press the power button for 2 seconds.
Off: press the power button for 5 seconds to turn off the device.
3. Video:
Video: press the power button2 seconds, the red light is on,and the device enters into
the standby mode.Click the power button once, the red indicator will flash 3 times then go
off ,the device enters into the video mode.
Save: while recording, click the power button once to end the record, and the red
indicator will be on, the device is back into standby mode.
One paragraph,5 minutes, support loop recording.
4. Motion Detection Mode:
After power on, the red light is on,and the device enters into the standby mode. Click
mode button once, the red and blue lights are on and the device enters into motion
detection mode.
In this mode, click the power button once, the red light is on, the blue light flashes,and
the device is at the detecting state. Once it detects any moving objects within the
range,the both indicators go off and it begins to record.2 minutes later,the device will stop
recording ,save data and return to detecting state of motion detection.The red light is on
and the blue light flashes.
Once any moving objects are detected, the lights will be off and the device enters in
to record.
Exit: Click the power button once to stop and save the video, return to standby mode,
the red and blue lights will be on.
One paragraph,2 minutes. And the effective distance of motion detection record is
about 3 metres and is affected by light intensity.
5. Photo:
After power on, the red light is on,and the device enters into the standby mode.Click the
mode button twice, the red light goes off, and the blue light is on,and the device enters into
the photo mode.
In this mode, click the power button once and the blue light flashes once to generate a
picture and save it. To continue taking pictures, click the power button again.
6. Infrared night vision lights switch:
Turn on: In any mode after power on, press the power button for 2 seconds and release,
the blue light flashes 2 times, infrared night lights is turned on.
Turn off: In any mode, press the power button for about 2 seconds to release, and the
blue light will flash 4 times to turn off the infrared night vision function.
7. Record with charging:
When the device is off, connect the device into a power source(the charger or power
bank), and the red and blue lights flash at the same time,the device is under the charging
state. Then click the power button once, the red light flashes three times and enters into
the recording mode. Press the power button again to exit the recording and save it.
Note: The device can’t enter the video mode when connecting into the computer.
8. Reset:

In case of system error or malfunctioning, reset the device by inserting a pin to the
reset hole.
9. Time setting:
1.）Upon power on, the device will generate a time file named “TIMERSET.TXT” in the
system.
2.）TURN OFF the device and connect it to a computer.
3.）Locate the “TIMERSET.TXT” file, set the desired time using format
20180101192526 Y and save the file.
4.）Disconnect the device from the computer then turn on the device. The time set is
then complete.
If you want to cancel the time stamp.Modify “Y” in “TIMERSET.TXT” file to “N” to disable
the time display.The reference format is as follows:
1: 20180101192526 Y (with time watermark display)
2: 20180101192526 N (no time watermark display)
Disclaimer
1. The usage of this device is subject to the relevant national laws and regulations,
DO NOT use this product for any illegal activities.
2. DO NOT point the camera lens to the direct sun light or permanent damage may
occur.
3. Keep away from fire. Never expose the device to any fire source.
4. DO NOT disassemble and modify. Doing so causes the risk of electric shock, burn
injury and other health related hazard.
5. DO NOT let water, liquids, or foreign matter get inside the device. Extra precaution
is advised where it is raining, snowing, near the ocean or other form of water. In
case any of the symptoms are present, turn off the device immediately and
contact us for further support.
6. DO NOT drop the device or permanent damage may occur.